Makita LXDT01Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita LXDT01Z manuals!
Problems with Makita LXDT01Z?
Ask a Question
Free Makita LXDT01Z manuals!
Problems with Makita LXDT01Z?
Ask a Question
Popular Makita LXDT01Z Manual Pages
Owners Manual - Page 1
IMPORTANTE: Leer antes de usar. 1 IMPORTANT: Lire avant usage. INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES
Cordless Impact Driver Tournevis à Chocs sans Fil Atornillador de Impacto Inalámbrico
LXDT01
011185
IMPORTANT: Read Before Using.
Owners Manual - Page 2
...-operated (corded) power tool or battery-operated (cordless) power tool. When operating a power tool outdoors... heat, oil, sharp edges or moving parts. Keep children and bystanders away while operating... and instructions for appropriate conditions
2 Use of an GFCI reduces the risk of electric shock.
8. Do not use . ENGLISH (Original instructions)
SPECIFICATIONS
Model
LXDT01
Machine ...
Owners Manual - Page 3
...accidentally occurs, flush with specifically designated battery packs. GEB054-1
CORDLESS IMPACT DRIVER SAFETY WARNINGS
1. Wear...only identical replacement parts. A wrench or a key left attached to be repaired. 19.... situations. 15. Follow instruction for the connection of ... or binding of moving parts. Service 28. Keep proper footing...keep it was designed. 18. Keep cutting tools sharp ...
Owners Manual - Page 4
...; F). It may result in this instruction manual may result in easily, it is ... instructions and cautionary markings on the tool. Installing ...part cannot be sure that the tool is removed before
completely discharged. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service...7.
Tips for tool. ･ volts
･ direct current
･ ...
Owners Manual - Page 5
...before the tool stops may damage the tool. • When not operating the tool, always set the reversing switch lever to change the direction of light
directly.
1. When the lamp lights up...before
operation. • Use the reversing switch only after switch trigger release, have tool serviced at a Makita service center.
When the lamp does not come on the switch trigger. Tool speed is ...
Owners Manual - Page 7
... either side of the
7 Screw
CAUTION: • Always be checked by a Makita local service center. To install the hook, insert it into the sleeve as for as it will go out approximately... using and have the tool repaired by pulling the switch trigger to the extent that the tool is switched off to the instructions above. • When it . Installing or removing driver bit or socket bit
12 ...
Owners Manual - Page 8
...fastened will differ according to the torque coefficient, the class of factors including the following troubleshooting related to perform inspection or maintenance except for the following .
NOTE: • Use...8226; Hold the tool pointed straight at low speed will cause a reduction in the figures. Driver bit or socket bit Failure to be sure that the screw is affected by a wide variety...
Owners Manual - Page 9
Troubleshooting
Trouble... or attachment for more details regarding these accessories, ask your Makita tool specified in this manual. If you need any assistance for more than 130 seconds...stop using Makita replacement parts.
Stop using and have the tool repaired by Makita Authorized or Factory Service Centers, always using and have the tool repaired by a Makita local service center. Light...
Owners Manual - Page 10
...Makita tool is caused by others: repairs are required because of Makita's Factory or Authorized Service Centers.
This Warranty does not apply where:
repairs have been made to state. EN0006-1
10 MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF "MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC... inspection shows the trouble is thoroughly inspected and...
Parts Breakdown - Page 2
... 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 33 35 35 35 36 A01 A02 A03 A04 E01
Part ID
188922-5 263005-3
868514-3 266130-9 419041-9 650632-9 ... 346317-0 DC18RA BL1830 891014-8
Part Name
HOUSING SET RUBBER PIN 6 INC. 35 LXDT01 NAME PLATE TAPPING SCREW BIND PT 3X16 F/R CHANGE LEVER SWITCH ROTOR STATOR UNIT CONTROLLER SET STATOR SET LED CIRCUIT TERMINAL RING SPRING 11...
Flyer (English) - Page 1
with ergonomicsoft gripfor reducedoperator fatigue
CONVENIENCE
Models LXDT01 LXDT01Z
Batterywarninglight flashes whenit istimetorecharge
the battery
BRUSHLESS 3-SPEED. makitatools.com of Max Torque • Battery Warning Light and Built-in .lbs. 18V LXT® BRUSHLESS 3-SPEED IMPACT DRIVER
PERFORMANCE
3-SPEED POWER SELECTION (0 - 1,300 / 0 - 2,000 / 0 - 2,600 RPM & 0 - 1,300 /
0 - 2,...
Flyer (English) - Page 2
...01Z
088381-610858
OPTIONAL ACCESSORIES
Model LXDT01
Model LXDT01Z
0 88381 61249 4
0 88381 61085 8
n Keyless impact n 38-Pc. light with precise fastening control for a wide range of Makita Corporation."
For a complete listing, please
refer to change without prior notice. 18V LXT® BRUSHLESS 3-SPEED IMPACT DRIVER
Models LXDT01/LXDT01Z
FEATURES & BENEFITS
n 3-speed power selection...
Makita LXDT01Z Reviews
We have not received any reviews for Makita yet.