Makita LS1221 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita LS1221 manuals!
Problems with Makita LS1221?
Ask a Question
Free Makita LS1221 manuals!
Problems with Makita LS1221?
Ask a Question
Makita LS1221 Videos
Makita LS1221 Miter Saw
Duration: :57
Total Views: 947
Duration: :57
Total Views: 947
Makita LS1221 12 Inch Compound Miter Saw Kit Review
Duration: :48
Total Views: 709
Duration: :48
Total Views: 709
Makita LS1221 12 Inch Compound Miter Saw Kit
Duration: :48
Total Views: 5
Duration: :48
Total Views: 5
Popular Makita LS1221 Manual Pages
Owners Manual - Page 1
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. www.makitatools.com Compound Miter Saw
Equipped with Electric Blade Brake 305 mm (12") MODEL LS1221
DOUBLE INSULATION
INSTRUCTION MANUAL
WARNING: For your personal safety, READ and UNDERSTAND before using.
Owners Manual - Page 2
... working order.
2
3. REMOVE ADJUSTING KEYS AND WRENCHES. KNOW YOUR POWER TOOL. SPECIFICATIONS
Blade diameter 305 mm (12") Hole diameter 25.4 mm (1") Max. For Your Own Safety Read Instruction Manual
Before Operating Tool
Save it on.
4. Miter angle Left 48°, Right 48° Max. Cutting capacities (H x W)
Bevel angle
Miter angle
0°
45° (left and right)
98 mm x 153...
Owners Manual - Page 3
....
12. DON'T OVERREACH. Make sure switch is damaged should be properly repaired or replaced.
20. Consult the owner's manual for best and safest performance. NEVER STAND ON TOOL. CHECK DAMAGED PARTS. check for which it frees both hands to operate tool.
13. When servicing use tool in presence of parts, mounting, and any way.
3 Keep work into a blade or...
Owners Manual - Page 4
...
4
against the turn base and guide fence with product (gained from repeated use this tool unsafely or incorrectly, you use ) replace strict adherence to miter saw without guards in doubt, DO NOT PLUG IN THE TOOL. If in good condition.
If you can still cause severe injury.
3. Check blade guard for saw blade. A power source with voltage...
Owners Manual - Page 8
...the hex bolt holding blade guard. Do not remove spring holding the center cover.
tact a Makita service center for a new guard. CAUTION:
5
• Before and after changing the bevel angle, always adjust... in such a way that the blade is impaired, use , adjust the kerf boards as described above and secure
bolt. Saw blade 2. Blade teeth 3. Straight cut
If the see-through age or UV...
Owners Manual - Page 9
Guide fence
CAUTION:
• After installing a new blade, always be sure that the blade does not contact any part of the lower base. CAUTION: • When turning the turn base, be sure to provide the maximum cutting capacity for a 305 mm (12") saw blade. Adjusting bolt 2 1
001835 Maintaining maximum cutting capacity
This tool is lowered completely. With the tool unplugged, rotate ...
Owners Manual - Page 13
... remove particles adher- NOTE:
If you connect a Makita vacuum cleaner to your saw, more efficient and cleaner operations can cause the tool to be damaged and/or the workpiece to do so can be destroyed. Also, after a cutting operation, DO NOT raise the blade until the blade has come to secure the center cover.
Failure...
Owners Manual - Page 16
... handle to the fully lowered position to perform the cut will vibrate and leave a mark (saw mark) in blade speed.
• Gently press down handle with force or if lateral force is applied, the blade will be sure to the previously covered "Adjusting the miter angle".
16 Miter cutting Refer to release the handle from the lowered...
Owners Manual - Page 17
... at angle shown in parallel with a vise. Bevel angle 45˚
Miter angle Left and Right 0 - 45˚
When performing compound cutting, refer to the left position when performing left bevel cuts.
4. Switch on a workpiece. Keep hands out of path of saw blade to set the sub-fence to "Press cutting", "Miter cutting" and "Bevel cut is dangerous.
001841 3. Then gently lower the...
Owners Manual - Page 18
... guide fence. A guide fence...blade. Finished piece will
be cut on a compound miter saw with the moldings laid flat on table to cut...saw angles. A).
(1) (2) (3) (4)
Fig.A
1
2
1. of cut length for test cuts to desired length. Adjust cut .
Inside corner 2. Table (A)
Molding
Bevel angle
position in Fig.
When cutting crown and cove moldings, set the bevel angle and miter...
Owners Manual - Page 19
A: • Tilt and secure bevel angle setting to 33.9°
LEFT. • Adjust and secure miter angle setting to 31.6°
RIGHT. • Lay crown molding with its broad back (hidden)
surface down on the turn base with its CEILING CONTACT EDGE against the guide fence on the saw. • The finished piece to be used will...
Owners Manual - Page 20
...˚
38˚
000031 Compound Miter Saw Miter and Bevel Angle Settings
EN0002-1
Wall
Wall to Crown Molding Angle: 52/38 degrees
Wall Angle Bevel Angle Miter Angle
(deg.)
(deg.)... 15.8
12.8
Wall Angle Bevel Angle Miter Angle
(deg.)
(deg.)
(deg.)
141 15.3
12.3
142 14.9
12.0
143 14.5
11.6
144 14.1
11.3
145 13.7
11.0
146 13.3
10.7
147 12.9
10.3
148 12.5
10.0
149 12.2
9.7...
Owners Manual - Page 21
...˚
45˚
000032 Compound Miter Saw Miter and Bevel Angle Settings
EN0003-1
Wall
Wall to Crown Molding Angle: 45 degrees
Wall Angle Bevel Angle Miter Angle Wall Angle Bevel Angle Miter Angle
(deg.)
(deg.)
....0
14.4
Wall Angle Bevel Angle Miter Angle
(deg.)
(deg.)
(deg.)
141 13.7
14.1
142 13.3
13.7
143 13.0
13.3
144 12.6
12.9
145 12.3
12.6
146 11.9
12.2
147 11.6
11.8...
Owners Manual - Page 23
... blade and/or the wood facing will facilitate more efficient operation. Align the cutting line on the holder as the wood facing.
• Use screws to attach the wood facing to 2,200 mm (7.2 ft.) approximately.
23 Then secure the set plate out of the workpiece. Set plate 2. Hole
105mm 115mm 115mm 105mm (4-1/8") (4-1/2") (4-1/2") (4-1/8")
98mm (3-7/8")
28mm (1-1/8")
1
3
1. Install...
Owners Manual - Page 27
...performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Lubricate the sliding portions with your local Makita service center. • Carbide-tipped saw blades
Miter saw blades For smooth and precise cutting in various materials.
• Vise assembly (Horizontal vise) • Vertical vise • Socket wrench 13 • Holder set • Holder...
Makita LS1221 Reviews
We have not received any reviews for Makita yet.