Makita HU06Z Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita HU06Z manuals!
Problems with Makita HU06Z?
Ask a Question
Free Makita HU06Z manuals!
Problems with Makita HU06Z?
Ask a Question
Popular Makita HU06Z Manual Pages
MU04 HU06 Instruction Manual - Page 2
... power tool. Personal Safety
1. ENGLISH (Original instructions)
SPECIFICATIONS
MU04 with shear blade for grass shear installed
Model: Cutting width Strokes per minute Dimensions (L ...specifications herein are subject to change without notice. • Specifications and battery cartridge may differ from heat, oil, sharp edges or moving parts. Failure to lose control.
Save all instructions...
MU04 HU06 Instruction Manual - Page 3
...serviced by a qualified repair person using electric gardening appliances, basic safety precautions should be repaired.
3. Exposure to a rotating part of dust extraction and collection facilities, ensure these instructions...accidentally occurs, flush with specifically designated battery packs. This will do the job better and safer at all charging instructions and do not allow ...
MU04 HU06 Instruction Manual - Page 4
... at all work area. Work gloves of stout leather are moving parts, breakage of fire.
19. Also wear sturdy shoes with specifically designated battery pack. Check damaged parts - Check for the subject product. Appliance service must not be properly repaired or replaced by an authorized service facility. Use of the appliance, a guard or other batteries may contact...
MU04 HU06 Instruction Manual - Page 5
...the safety rules stated in this instruction manual may result in the battery ...repair immediately. 16. Store the hedge trimmer with the cutter running.
It may cause serious personal injury.
Do not use genuine Makita batteries. For preparation of faults, or removing material caught in a container with the unit can be hung on the cover.
Overcharging shortens the battery service...
MU04 HU06 Instruction Manual - Page 7
...Makita Service... again but stops soon. Switch action
WARNING: Before installing the battery cartridge into the tool, always check to...shearing height can be careful not to overload. The lockoff button can be set to be taken
Indicator lamp
Status
Action to three levels (15 mm (9/... lamp blinks red.
Adjusting the shearing height (for repairs. In this tool is not enough, the tool stops ...
MU04 HU06 Instruction Manual - Page 8
... may vary depending on the tool by sliding the grass receiver toward the front of the tool.
1
► 1 . NOTICE: When replacing the shear blades, do not directly contact the blades. To install the blade cover, perform the steps in the direction of the tool.
1
2
► 1 . Grass receiver
2. NOTE: The shearing height value...
MU04 HU06 Instruction Manual - Page 9
...the three pins so that they are lined up on the lock lever.
► 1 . Installing or removing the shear blades for grass shear
Removing the shear blades
1. Prepare the crank, undercover...on the grass receiver with on the alignment line.
9 ENGLISH Shear blades 3. Shear blades
2. Crank
Installing the shear blades
1. Crank 2. Undercover 3.
1 2
3
NOTICE: Do not attach the hinge of...
MU04 HU06 Instruction Manual - Page 10
... blades and base plate so that the pins on the tool fit in the hole on the undercover.
6. Turn the shear blades upside down and install them so that the hole in the base plate and the two protrusions on the blades are fixed securely in the groove on the base...
MU04 HU06 Instruction Manual - Page 11
... then turn the undercover counterclockwise until on the undercover is aligned with a screwdriver and remove the shear blades.
1
2. Installing or removing the shear blades for hedge trimmer
CAUTION: Attach the blade cover before removing or installing the shear blades. Removing the shear blades
1.
Screws
NOTE: The shear blades can be removed without...
MU04 HU06 Instruction Manual - Page 12
...9658; 1 . Tighten the two screws firmly with the small and large rounds facing down and install them so that the hole on the alignment line.
1
6. Apply a small amount of ...the crank. Undercover 3. Attach the crank to the pins with a screwdriver.
12 ENGLISH Installing the shear blades
1
1. Crank 2. Make sure that they are fixed securely in the hole on ...
MU04 HU06 Instruction Manual - Page 13
... the chip receiver, press the levers on the lock lever.
► 1 . Lock lever
CAUTION: Never use the tool without installing the undercover.
11. Installing or removing the chip receiver
Optional accessory
CAUTION: When installing or removing the chip receiver, always wear gloves and attach the blade cover so that on the undercover is...
MU04 HU06 Instruction Manual - Page 16
...alcohol or the like. Cleaning the tool
Clean the tool by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Blade maintenance
Before the operation or once per hour during ... the root to perform inspection or maintenance.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be sure that the tool is removed before...
MU04 HU06 Instruction Manual - Page 17
...specific legal rights, and you need any trouble develop during this manual. Should any assistance for more details regarding these accessories, ask your Makita... are required because of Makita's Factory or Authorized Service Centers. Attach the blade...repairs have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge.
HU06Z Parts Breakdown - Page 2
... PIN 6 FLAT WASHER 6 PIN 4 HELICAL GEAR 47 ASS'Y INC. 19 CRANK COMPLETE DC MOTOR PIN 6 FLAT WASHER 6 GEAR 12-31 HOUSING SET HEX. Model HU06Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
Q'ty Unit
001
915116-7
002
144495-8
002 C10 812G28-6
003
183G04-0
003 C10 931102-0
003 C20 263002-9
003 C30 346275...
HU06Z New Tool Flyer English - Page 1
... Hedge Trimmer, Tool Only
Model HU06Z
Tool-Less Blade Changing System
POWER
Delivers 2,500 SPM; up to absorb vibration for more comfortable operation
n Part of the expanding 12V max CXT™ series, combining performance with superior ergonomics in a compact size
Shipping Weight UPC Code
n Not compatible with the U.S. makitatools.com
Makita U.S.A., 14930 Northam St., La...
Makita HU06Z Reviews
Do you have an experience with the Makita HU06Z that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!