Makita GA5093 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita GA5093 manuals!
Problems with Makita GA5093?
Ask a Question
Free Makita GA5093 manuals!
Problems with Makita GA5093?
Ask a Question
Makita GA5093 Videos
Makita Angle Grinder - GA5095 & GA5093
Duration: :26
Total Views: 776
Duration: :26
Total Views: 776
Popular Makita GA5093 Manual Pages
Instruction Manual - Page 2
...instructions listed below may differ from heat, oil, sharp edges or moving parts... (Original instructions)
SPECIFICATIONS
Model: Applicable ...instructions, illustrations and specifications provided with earthed or grounded surfaces, such as 4-1/2″ on the attachment(s). Power tools create sparks which may differ depending on the tool, 115mm (4-1/2″) wheels can cause you install...
Instruction Manual - Page 3
... it was designed.
2. Follow instruction for advice before use common sense...install the proper outlet. Ensure the switch is harmful to a rotating part...tool in personal injury.
5. Service
1. If the plug does not...repaired.
3. Use the correct power tool for which may result in the off . Power tools are easier to operate the power tool. When using only identical replacement parts...
Instruction Manual - Page 4
...installing an accessory, position yourself and bystanders away from work area must be forced in a way which in turn causes the uncontrolled power tool to follow all safety warnings, instructions, illustrations and specifications...complete stop. Operations for one minute. Read all instructions listed below may make exposed metal parts of the power tool. Sparks could give the operator...
Instruction Manual - Page 5
...bouncing have a tendency to the power tool and positioned for the application being performed. Safety warnings specific for sanding operations:
1. The guard must be mounted below .
1. A wheel intended for .... Investigate and take corrective action to do not grind with a negative rake angle. Supports must be different from the cut -off wheel from grinding wheel flanges.
6. Before ...
Instruction Manual - Page 6
...properly supported.
... replace strict...installing a grinding wheel, always check that wire bristles are thrown by applying excessive load to follow the safety rules stated in serious personal injury.
3. Safety warnings specific...part does not have any interference of the manufacturer for correct mounting and use separate reducing bushings or adaptors to safety rules for this instruction manual...
Instruction Manual - Page 7
... automatically reduces or cuts off the tool. Overheat protection
Country specific When the tool is overheated, the tool stops automatically and ...
Speed adjusting dial
Only for model GA4593 / GA5093
CAUTION: If the tool is operated continuously at low speeds for the relationship between the number settings on the tool.
The rotating... spindle rotation when installing or removing accessories.
Instruction Manual - Page 8
...lock lever with lock-off lever is switched off the switch, and turn off . Fig.5
Installing or removing wheel guard
WARNING: When using an abrasive cut -off wheels.
8 ENGLISH Constant ...always check to see that the switch lever actuates properly and returns to our authorized service center for proper repairs BEFORE further usage. This can cause switch breakage. WARNING: Make sure that the...
Instruction Manual - Page 9
... straight. Wheel guard 2.
NOTE: Push down the portions B of the wheel guard as shown in reverse.
C
1
3
A 2
C
Fig.6 ► 1 . Hole
To remove wheel guard, follow the installation procedure in the figure.
For depressed center wheel, flap disc, flex wheel, wire wheel brush / abrasive cut-off operations, a clip-on cutting wheel guard attachment...
Instruction Manual - Page 10
... onto the spindle.
3. Inner
flange Follow instructions for depressed center wheel but also use and guard helps to fit the dented part of the inner flange onto the straight part at the bottom of the spindle. Shaft lock
To remove the wheel, follow the installation procedure in this manual. Fig.13 ► 1 . NOTE: Use sander...
Instruction Manual - Page 11
... (Thinner than 4 mm
(5/32″)) 3. Inner flange
Installing wire cup brush
Optional accessory CAUTION: Do not use brush that...Installing abrasive cut-off / diamond wheel
Optional accessory WARNING: When using an abrasive cut-off
/ diamond wheel, be sure to use only the special wheel guard designed for use with cut-off wheel / diamond wheel
As for the installation, follow the instructions...
Instruction Manual - Page 12
...accessories on the spindle.
Wire wheel brush
Installing hole cutter
Optional accessory Place the tool upside down to allow easy access to the manual of balance. Cup-type diamond wheel 3....5. Hole cutter
12 ENGLISH
CAUTION: ALWAYS use guard with a cup-type diamond wheel.
Installing wire wheel brush
Optional accessory
CAUTION: Do not use wire wheel brush that a vacuum cleaner...
Instruction Manual - Page 13
...instruction manual of the dust collecting wheel guard.
Refer to the instruction manual attached to the dust collecting wheel guard for assembling and using it may result in contact with dust or foreign matters. WARNING: ALWAYS replace... wheel may cause an injury to operator. Dust collecting wheel guard 2.
Install the dust cover attachment to force the tool.
NOTICE: Clean out the...
Instruction Manual - Page 15
...cutter
Optional accessory CAUTION: Check operation of the hole cutter
by Makita Authorized or Factory Service Centers, always using wire wheel brush. NOTICE: Never use gasoline, benzine, thinner, alcohol... and RELIABILITY, repairs, any other maintenance or adjustment should be sure that no one is in front of or in front of wires when using Makita replacement parts.
It may lead...
Instruction Manual - Page 16
...
CAUTION: Using the tool with incorrect guards can cause risks as specified in "SPECIFICATIONS", the wires may interfere with the work-
Grinding / Sanding - Grinding / Sanding -
Sanding - Wire brushing Wire brushing Hole cutting
115 mm (4-1/2″) model
125 mm (5″) model
Side grip
Wheel guard (for cutting-off operations with bonded abrasive wheels and...
Instruction Manual - Page 17
... to a vacuum cleaner, refer to the warranty details set forth at below website for cut-off wheel)
15...refer to each instruction manual of any assistance for the most current warranty terms applicable to this manual. Dust collecting ...type diamond wheel
-
-
- Only use with your local Makita Service Center. • Accessories listed in "COMBINATION OF
APPLICATIONS AND ACCESSORIES...
Makita GA5093 Reviews
We have not received any reviews for Makita yet.