Makita CT232 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita CT232 manuals!
Problems with Makita CT232?
Ask a Question
Free Makita CT232 manuals!
Problems with Makita CT232?
Ask a Question
Popular Makita CT232 Manual Pages
DT03 Instruction Manual - Page 3
... . Service 1. Wear ear protectors. 5. volts
direct current
no one terminal to control.
7. Disconnect the plug from the power source and/or the battery pack from those intended could give the operator an electric shock.
2. Power tools are caused by a qualified
repair person using only identical replacement parts. Many accidents are dangerous in this instruction manual may...
DT03 Instruction Manual - Page 4
... adjusting or checking function on the tool. SAVE THESE INSTRUCTIONS. Never recharge a fully charged battery cartridge. FUNCTIONAL DESCRIPTION...install the battery cartridge fully until it from the tool while sliding the button on the upper side of the model... is completely worn out. Overcharging shortens the battery service life.
3. To install the battery cartridge, align the tongue on the tool...
DT03 Instruction Manual - Page 5
... "OFF" position when released. Reversing switch action
1
1 A
1.
Check button
Press the check button on lighting while the switch trigger is released, have the tool serviced at a Makita service center.
Lamp
CAUTION: Do not look in the light or see that the switch trigger actuates properly and returns to indi- Pull the switch trigger...
DT03 Instruction Manual - Page 6
...instructions above. In this case, try re-inserting the bit according to secure the driver bit.
NOTE: After inserting the driver bit, make sure that the tool is switched off and the battery cartridge is shown in the figure. Groove 2. To install... set the reversing switch lever to a complete stop.
NOTE: If the driver bit is convenient for counterclockwise rotation. Installing ...
DT03 Instruction Manual - Page 8
... of any trouble develop during this manual. The use gasoline, benzine, thinner, alcohol or the like.
THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. You can keep two driver bits at our option, replace) without charge.
Should any other accessories or attachments might present a risk of Makita's Factory or Authorized Service Centers...
DT03R1/Z Parts Breakdown - Page 2
Model DT03R1/Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
001
183B49-8 HOUSING SET
001 C10 252126-6 HEX. LOCKING NUT M4-7
001 ... 12
028
227215-6 INTERNAL GEAR 43
029
158671-8 BEARING BOX COMPLETE
030
629163-9 DC MOTOR
031
183B49-8 HOUSING SET
031 C10 252126-6 HEX. LOCKING NUT M4-7
031 D10
INC. 1
A01
266622-8 + TRUSS HEAD SCREW M4X12...
FD09 FD10 Instruction Manual - Page 2
....
• Specifications may differ from heat, oil, sharp edges or moving parts. SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all instructions listed below may...fumes. 3. Use of a cord suitable for outdoor use any way. ENGLISH (Original instructions)
SPECIFICATIONS
Model: Drilling capacities Fastening capacities No load speed (RPM) Overall length
Steel Wood Wood screw...
FD09 FD10 Instruction Manual - Page 4
... such as indicated in a container with the products specified by the manufacturer or authorized service providers.
3. Never service damaged battery packs. Important safety instructions for tool. For preparation of control can explode in this instruction manual may be performed by Makita. Installing the batteries to water or rain. volts
direct current
no one is maintained...
FD09 FD10 Instruction Manual - Page 5
... battery voltage: The remaining battery capacity is too low and the tool will also void the Makita warranty for maintaining maximum battery life
1. Indicator lamps 2. Insert it into place. Always stop ...in easily, it . Overcharging shortens the battery service life.
3. FUNCTIONAL DESCRIPTION
CAUTION: Always be seen. CAUTION: Always install the battery cartridge fully until it locks in...
FD09 FD10 Instruction Manual - Page 6
...trigger. Tool speed is being pulled. CAUTION: When not operating the tool, always set the speed change lever positioned halfway between the "1" side and "2" side, the tool...set the reversing switch lever to change lever while the tool is released, have the tool serviced at a Makita service center. If you operate the tool with an electric brake. Switch trigger
CAUTION: Before installing...
FD09 FD10 Instruction Manual - Page 8
... not use any work on either side and then secure it out.
8 ENGLISH Sleeve 2. Close 3. Installing or removing driver bit/ socket bit
For Model FD10 (optional accessory)
1 2
► 1 . Then release the sleeve to the instructions above. NOTE: If the driver bit is convenient for temporarily hanging the tool.
Groove 2. Screw
The hook is not inserted...
FD09 FD10 Instruction Manual - Page 9
... on the tool/drill bit at the point to back out. The guide screw makes drilling easier by setting the reversing switch to reverse rotation in place. The exceptions are obtained with...for your drill bit, decrease the tool performance and shorten the service life of the drill bit in . Place the point of the tool. Installing driver bit holder
Optional accessory
1
2
► 1 . If you...
FD09 FD10 Instruction Manual - Page 11
... your local Makita Service Center. • Drill bits • Driver bits • Socket bits • Driver bit holder • Holster • Plastic carrying case • Hook • Makita genuine battery and charger NOTE: Some items in the list may differ from country to this manual. United States of injury to the warranty details set forth at below...
FD09 Parts Breakdown - Page 2
.... LOCKING NUT M4-7
021 D10
INC. 1
A01
251314-2 + SCREW M4X12
A02
346909-5 HOOK
A04
821661-1 PLASTIC CARRYING CASE
A04 C10 417724-5 LATCH
A05
818R05-2 FD09R1 MODEL NO. LABEL
021
183K90-5 HOUSING SET
021 C10 252126-6 HEX. Model FD09R1, FD09Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
Q'ty Unit
001
183K90-5 HOUSING...
CT232 New Tool Flyers English - Page 1
....com of Max Torque
• 3/8" Driver-Drill features a compact design at only 6" long and weighs only 2.3 lbs. Combo Kit (CT232RX) 2. 12V max CXT® Lithium-Ion 4.0Ah Battery (BL1041B) 3. 66 Pc. Contractor-Grade Bit Set, 70-Pc. (T-01725)
1
2
3
4
5
All specifications subject to stand for work in .lbs. The Makita Teal Color is the trade dress...
Makita CT232 Reviews
We have not received any reviews for Makita yet.