Makita AN611 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita AN611 manuals!
Problems with Makita AN611?
Ask a Question
Free Makita AN611 manuals!
Problems with Makita AN611?
Ask a Question
Most Recent Makita AN611 Questions
Contact Arm
I need to install a new contact arm on my an611. should I remove the trigger Assembly or the hole fr...
I need to install a new contact arm on my an611. should I remove the trigger Assembly or the hole fr...
(Posted by noblebuildingllc 3 years ago)
Makita AN611 Videos
Makita AN611 1 1 4 Inch to 2 1
Duration: :48
Total Views: 0
Duration: :48
Total Views: 0
Makita AN611 1-1/4-Inch to 2-1/2-Inch Coil Siding Nailer Review
Duration: :48
Total Views: 118
Duration: :48
Total Views: 118
Popular Makita AN611 Manual Pages
Owners Manual - Page 1
... 127 mm x 31 7 mm (13-1/16" x 5" x 12-1/2")
* Manufacturer reserves the right to change specifications without notice.
* Note: Specifications may differ from country to country.
\ A / A R h l l h l C .
Construction Coil Nailer
MODEL AN61 1
INSTRUCTION MANUAL
SPECIFICATIONS
Air pressure
I
Applicable length
I
Nail capacity
4.5 - 8.5 kgf/cmZG ( 6 5 - 120 PSIG)
32 mm, 38 mm, 45 mm, 50 mm...
Owners Manual - Page 6
...
Check walls, ceilings, floors, roofing and the like carefully to the LOCK position. Use only nails specified in this manual.
caused by striking live wires, conduits or gas pipes. Make sure that the trigger is locked when the change lever is set to avoid possible electrical shock, gas leakage, explosions, etc.
Do not permit...
Owners Manual - Page 8
... is high pressure inside the tool that dust, sand, chips and foreign matter will not enter the tool in the place where you leave it setting.
*Do not point the ejection port at anyone in the sun. Be sure that can be dangerous if a crack is connected, do not carry the...
Owners Manual - Page 10
... tool if it does not contain a legible WARNING LABEL.
Ask Makita's Factory or Authorized service center for periodical inspection of the tool. SAVE THESE INSTRUCTIONS.
10 To maintain product SAFETY and RELIABILITY, maintenance and repairs should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
Do not modify tool without authorization from...
Owners Manual - Page 11
...*
When an air set (oiler,
regulator, air filter) as close as possible to tool operator or persons in serious injury to assure continuous, efficient nailing operation. Pneumatic tool... maximum pressure produced in the driving capability of the tool. TOOL INSTALLATION INSTRUCTIONS AND USE
Selecting compressor
The air compressor must be used , oil the tool with an air output over 6.5 mm ...
Owners Manual - Page 12
.... When nailing workpieces with the coil support plate set it from being lost.
Select nails suitable for your work.
If the tool is factory installed at the rear of the tool. When loading 45 or 50 mm (1-3/4", 2") long nails, use the nose adapter. Nose adapter CAUTION: Always lock the trigger and disconnect the hose before loading the nailer. It...
Owners Manual - Page 13
... will become shallower as the arrow points to the number 1. No. 2 method is used with
./
lower air pressure and the adjuster set properly in approx. 1.0 mm (1/32") increments per graduation. Adjusting depth of nailing, turn the adjuster so that the nail coil is the deepest when the arrow points to higher number. To adjust the...
Owners Manual - Page 14
... necessary. This hook can be installed on either side of the tool. nailing
Trigger lock
Exhaust cover
-/
Jammed nailer CAUTION: Always lock the trigger, disconnect the hose and remove the nails from the tool.
14
I
Hook The hook is properly set the change lever to the "Continuous Nailing" position. For No. 2 method, set the change lever to drive...
Owners Manual - Page 16
...when the change lever is pressed against the wood. Maintenance of nailer Always check the tool for possible faulty operation with nails unloaded. Make sure all safety systems are performed. It must not... operate if only the trigger is pulled or if only the contact element is set to perform inspection...
Owners Manual - Page 17
If moisture is sufficient pneumatic oil in the oiler of the air set and air hose
After operation, always drain the compressor tank and the air filter... safe place. Oiler/ - I 1
I Pneumatic 011 When the tool is not to be used for an extended period of time, lubricate the tool using pneumatic tool oil and store the tool in poor performance and possible tool failure. Avoid exposure to ...
Owners Manual - Page 18
... abrasion to the hose. Also, route the hose away from chemicals (thinner, strong acids or alkalis).
Hoses must also be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
18 Keep the air hose away from heat (over 6OoC,over 140°F),
away from obstacles which may become dangerously caught on during...
Owners Manual - Page 19
... Makita will repair (or at our option, replace) without charge. MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF "MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC ...USE OF THE PRODUCT. THlS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. Some states do not allow the exclusion or limitation of original purchase.
Should any trouble...
Parts Breakdown - Page 2
... 39, AN611 SEPARATOR, AN611 O RING 23, AN611 HEAD VALVE, AN611 O RING 48, AN611 VALVE SHEET, AN611 CYLINDER SEPARATOR, AN611 O RING 67, AN8300 O RING 36, AN611 DRIVER COMPLETE, AN611 O RING 47, AN8300, T1 O RING 46, AN611 CYLINDER, AN611 CUSHION GUIDE, AN611 CUSHION F, AN611 PIN 5, AN611 H.S.H BOLT M6X20, AN611 URETHANE RING 3, AN451 DRIVER GUIDE, AN611 DRIVER GUIDE, AN611
O RING 45, AN611 STOPPER...
Parts Breakdown - Page 3
...O RING 17, AN451
1
PISTON, AN611
1
COMPRESSION SPRING 9, AN611
1
RUBBER RING 16, AN611
1
CUP WASHER 5, AN611
1
RETAINING RING R-24, AN611
1
H.S.H. BOLT M4X10, AN611
1
COMPRESSION SPRING 6, AN611
1
LOCK PIN, AN611
1
PIN 4, AN611
1
COMPRESSION SPRING 4, 4304
1
CHECK CLAW, AN611
1
NAIL HOLDER, AN611
1
NAIL HOLDER, AN610H
1
ARM, AN611
1
ARM, AN610H
1
COMPRESSION SPRING...
Parts Breakdown - Page 4
1,001 1,002 1,003 1,004 1,005 2,001
195246-2 181434-7
421574-2 783202-0 824490-1 193007-4
Parts Breakdown
N/A OIL SUPPLY 30CC, AF502
NOSE ADAPTER, AN611 HEX WRENCH 4, JR3000V PLASTIC CARRYING CASE, AN611 FIRST AID KIT, AN611
AN611
1 1 1 1 1 1
Page 4 of 4
8/18/2010
Makita AN611 Reviews
We have not received any reviews for Makita yet.