Owners Manual
Page 7
... • Do not recharge, short-circuit, heat, burn or disassemble batteries. Accessories Check the following accessories when unpacking the STB: Remote control: NA387UD (x1) Owner's manual: 1VMN25974 (x1) AA battery (x2) RF cable: WPZ0901TM002 / WPZ0901TM005 (x1) Installing Batteries Instalaci...243;n de pilas 1 Unsnap the battery cover from battery compartment that the resolution of the remote control. Instale dos pilas AA asegurándose que la polaridad (+ / - ) sea la correcta. 3 Snap the battery cover back...
... • Do not recharge, short-circuit, heat, burn or disassemble batteries. Accessories Check the following accessories when unpacking the STB: Remote control: NA387UD (x1) Owner's manual: 1VMN25974 (x1) AA battery (x2) RF cable: WPZ0901TM002 / WPZ0901TM005 (x1) Installing Batteries Instalaci...243;n de pilas 1 Unsnap the battery cover from battery compartment that the resolution of the remote control. Instale dos pilas AA asegurándose que la polaridad (+ / - ) sea la correcta. 3 Snap the battery cover back...
Owners Manual
Page 13
.... Puede alternar entre el c3 y 4 manteniendo presionado [SETUP] durante 3 segundos. Initial Setup (Setup Wizard) Initial Setup Ajùste inicial 1 Press [STANDBY-ON] on the remote control to your TV's ch3 is already occupied, select ch4, and set the each setting. 13 EN Si el c3 de su TV ya está...
.... Puede alternar entre el c3 y 4 manteniendo presionado [SETUP] durante 3 segundos. Initial Setup (Setup Wizard) Initial Setup Ajùste inicial 1 Press [STANDBY-ON] on the remote control to your TV's ch3 is already occupied, select ch4, and set the each setting. 13 EN Si el c3 de su TV ya está...
Owners Manual
Page 30
... on . • This is a normal part of the problem. When autoscan is securely plugged into the power outlet. • Make sure to point the remote control at step 5 in the "Initial Setup (Setup Wizard)". ( Page 14.) • Make sure to complete autoscan in "SETUP WIZARD" or in the correct... Before requesting service, check the table below for a possible cause of the start-up process and is not responding to the remote control. Select "RF OUT" at the remote control sensor. • You may be too far from STB. Try moving closer. • Remove any obstacles between the...
... on . • This is a normal part of the problem. When autoscan is securely plugged into the power outlet. • Make sure to point the remote control at step 5 in the "Initial Setup (Setup Wizard)". ( Page 14.) • Make sure to complete autoscan in "SETUP WIZARD" or in the correct... Before requesting service, check the table below for a possible cause of the start-up process and is not responding to the remote control. Select "RF OUT" at the remote control sensor. • You may be too far from STB. Try moving closer. • Remove any obstacles between the...
Owners Manual
Page 32
... the date of ninety (90) days from fire, flood, lightning or other person or transferee. THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS. ATTENTION: FUNAI CORP. FUNAI CORP. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO...
... the date of ninety (90) days from fire, flood, lightning or other person or transferee. THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS. ATTENTION: FUNAI CORP. FUNAI CORP. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO...