LiftMaster SL585101U Support and Manuals
Get Help and Manuals for this LiftMaster item
View All Support Options Below
Free LiftMaster SL585101U manuals!
Problems with LiftMaster SL585101U?
Ask a Question
Free LiftMaster SL585101U manuals!
Problems with LiftMaster SL585101U?
Ask a Question
Most Recent LiftMaster SL585101U Questions
Reset Switch
I ordered a reset switch for our SL585101U gate, part # K23-34815-1. It does not work. On the board ...
I ordered a reset switch for our SL585101U gate, part # K23-34815-1. It does not work. On the board ...
(Posted by lschlechter 2 years ago)
Popular LiftMaster SL585101U Manual Pages
LiftMaster SL585 Sell Sheet Manual - Page 2
... cabinet withstands extreme and harsh environments. Exclusively LiftMaster®: What Sets Us Apart
Lockout/Tagout Feature prevents power from high-voltage power.... property, preventing unauthorized access.
Lockable Manual Disconnect when unlocked allows gate to pre-existing pads for Link, Stanley or LiftMaster operators.
SL585: Setting the New Standard with Security+ 2.0&#...
SL585151U Installation Manual - Page 1
Model SL585
ELITE SERIES INDUSTRIAL
AC SLIDE GATE OPERATOR
INSTALLATION MANUAL
SL585101U
1 HP, 120/208-240 Vac Single Phase
SL585103U
1 HP, 208-240/480...Phase
SL585505U
1/2 HP, 575 Vac Three Phase
• THIS PRODUCT IS TO BE INSTALLED AND SERVICED BY A TRAINED GATE SYSTEMS TECHNICIAN ONLY.
• This model is for use on vehicular passage gates ONLY and not intended for use on pedestrian passage...
SL585151U Installation Manual - Page 5
...install...8226; SAVE THESE INSTRUCTIONS.
3 UL325 ...service the general public. IMPORTANT SAFETY INFORMATION
To reduce the risk of device shall not be installed with gate controls. Have a qualified service person make repairs... not servicing the ...ALL INSTRUCTIONS....servicing the general public. The gate MUST reverse on contact
with a residence of travel, retest the gate operator.
The installer...
SL585151U Installation Manual - Page 16
... are constructed out of the gate. 2. Rear Gate Bracket
Manual Release Handle
14
Front Gate Bracket Chain Guide Remove the operator cover. 3. A general rule of idler sprocket...be used as a chain support. Locate and engage the manual release handle and lock it in line with the provided hardware. 5. INSTALLATION
STEP 2
ATTACH THE CHAIN
DO NOT run the operator until instructed. 1.
SL585151U Installation Manual - Page 18
... switch settings (located next to the terminals) Switch set to CLOSE: gate reverses fully when an obstruction is sensed Switch set to the specific entrapment protection device manual for the...settings (located next to the terminals) Switch set to CLOSE: gate reverses fully when an obstruction is sensed Switch set to -Close. When an obstruction is sensed during gate opening .
INSTALLATION...
SL585151U Installation Manual - Page 25
...NORMAL MODE HANDING SETUP MODE HANDING SETUP MODE HANDING SETUP MODE
NORMAL MODE NORMAL MODE
EXPLANATION
Control board not powered. Handing set to the direction of the solid LED Handing set to the direction...is directly over the flat portion of the operator, you must be set . During the installation of the shaft. Set Screws
Torque Nut
Gear Reducer Output Shaft
Friction Clutch
23 STEP 8...
SL585151U Installation Manual - Page 34
... buzzer or light (low voltage).
After servicing, set all the LEDs will turn on (gate in thousands), set Aux Relay switches back to the ON setting for 10 seconds, then turn off .... blink out the cycle count (cycle count is between 1,000 and 9,999,000 cycles. Cycle count is manually tampered with by being pushed off . GATE STATE
AUX RELAY 1 SWITCHES
AUX RELAY 2 SWITCHES
1 OFF ...
SL585151U Installation Manual - Page 37
...8226; DISCONNECT power (AC or solar and battery) BEFORE installing or servicing operator. STATION
-
+
FIRE DEPARTMENT
-
N.C.
NOTE: ...Lock (Optional)
Maglock (Optional)
OR (Not Provided)
PLUG-IN LOOP DETECTOR Model LOOPDETLM
EXPANSION BOARD
POWER
NOTE: These switches determine if the corresponding photoelectric sensor or...Replace ONLY with fuse of each operator.
COM N.O.
SL585151U Installation Manual - Page 40
...setup the operator system to ON. Gate Motion Aux Relay Out -
Normally set to prevent vehicle tail-gating, CLOSE EYES/Interrupt loop pauses a closing gate. In attempt to OFF. For DUAL-GATE site, set to For DUAL-GATE site, set to indicate if gate is manually... cycles.
Use during servicing only to Use during servicing only to indicate if gate is manually tampered with by being...
SL585151U Installation Manual - Page 42
... ALL INSTRUCTIONS.
• ANY maintenance to the operator or in accordance with national and local electrical codes. Keep...manual. To protect against fire: • Replace ONLY with a rigid object or reverse when an object activates the noncontact sensors. For continued protection against fire and electrocution:
• DISCONNECT power (AC or solar and battery) BEFORE installing or servicing...
SL585151U Installation Manual - Page 44
...replace main control board. Max-Run-Time Exceeded Error
Attempt to force a fresh boot.
If so, erase limits, enter limit setup mode and set...installed too far apart.
Max-RunTime can be installed too far apart. Product ID Error
Was the control board just replaced?
May be re-measured by setting... installed
too far apart.
TROUBLESHOOTING
DIAGNOSTIC CODES continued... Some codes ...
SL585151U Installation Manual - Page 47
... detector setup incorrectly not cause gate to control board.
Repair gate as needed . Repair gate as needed .
a) Check all Open and Close inputs for a "stuck on" input b) Check Stop button is not "stuck on" c) Check Reset button d) Check all Entrapment Protection Device inputs for a "stuck on " detector f) Replace defective control board
a) Use manual disconnect, manually move...
SL585151U Installation Manual - Page 48
TROUBLESHOOTING
TROUBLESHOOTING CHART continued...
Adjust settings as needed .
c) Move the photoelectric sensors closer together or use edge sensors instead. b) Replace defective edge sensor. Press the
reset button to open or close is
given
SOLUTIONS a) Review Shadow loop detector settings. Solenoid lock not working correctly. and COM terminals. a) Incorrect photoelectric ...
SL585151U Installation Manual - Page 50
... Complete with: Chain guard, chain guides and retainers Reset Button with ID Harness Assembly Optional Diagonal Brace Kit for chassis Gate Bracket Take-up Bolt Chain #50, Nickel Plated - 25'
HTR460 K80-9001 K75-34824 K94-37753 65-3506 K10-3209 K11-3503 K19-3025
ELECTRICAL BOX REPAIR PARTS (NOT SHOWN)
Power Board...
SL585151U Installation Manual - Page 51
... PERIOD SET FORTH ABOVE, AND NO IMPLIED WARRANTIES WILL EXIST OR APPLY AFTER SUCH PERIOD. Some states do not allow limitations on your compliance with new or factory-rebuilt parts at no cost to you and returned pre-paid and insured, to our service center for warranty repair. ANY SERVICE CALL THAT DETERMINES THE PROBLEM HAS...
LiftMaster SL585101U Reviews
We have not received any reviews for LiftMaster yet.