KPR2000 Waterproof Keypad/Proximity Reader Manual
Page 2
...; 10 Panic Card/PIN Codes • Low power consumption (50mA) • Anti-Tamper Alarm • Latch Mode to hold door or gate open the entry and set off the alarm). INTRODUCTION The LiftMaster KPR2000 is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any...
...; 10 Panic Card/PIN Codes • Low power consumption (50mA) • Anti-Tamper Alarm • Latch Mode to hold door or gate open the entry and set off the alarm). INTRODUCTION The LiftMaster KPR2000 is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any...
KPR2000 Waterproof Keypad/Proximity Reader Manual
Page 4
... Pink Green (Data 0) White (Data 1) Pink (must connect for Alarm Contact Input Door/Gate Contact Input (Normally Closed) WIRING EXAMPLES: Gate/Door Operator or Fail-Secure Strike Magnetic Lock or Fail-Safe Strike Normally Open Install a 1N4007 or equivalent diode. KPR2000 External Alarm (1 Amp Maximum) Common Blue Purple Red Gray Pink Black 123 456...
... Pink Green (Data 0) White (Data 1) Pink (must connect for Alarm Contact Input Door/Gate Contact Input (Normally Closed) WIRING EXAMPLES: Gate/Door Operator or Fail-Secure Strike Magnetic Lock or Fail-Safe Strike Normally Open Install a 1N4007 or equivalent diode. KPR2000 External Alarm (1 Amp Maximum) Common Blue Purple Red Gray Pink Black 123 456...
KPR2000 Waterproof Keypad/Proximity Reader Manual
Page 5
...The relay time is 1-99 seconds (default is used to prevent unauthorized access to disengage only after engaging or it can be granted access. SET DOOR OPEN TOO LONG (DOTL) ALARM This setting requires an external sensor input. Factory default is 1 minute). Strike-Out ON OR 2. Programming Step Keystroke ...followed by the # key, in order to be granted access. • Card Only: The User must first present a valid Wiegand Card to the KPR2000 and then enter their PIN code followed by the # key, in order to be set from 1-3 minutes (default is OFF. Programming Step 1. Programming...
...The relay time is 1-99 seconds (default is used to prevent unauthorized access to disengage only after engaging or it can be granted access. SET DOOR OPEN TOO LONG (DOTL) ALARM This setting requires an external sensor input. Factory default is 1 minute). Strike-Out ON OR 2. Programming Step Keystroke ...followed by the # key, in order to be granted access. • Card Only: The User must first present a valid Wiegand Card to the KPR2000 and then enter their PIN code followed by the # key, in order to be set from 1-3 minutes (default is OFF. Programming Step 1. Programming...
KPR2000 Waterproof Keypad/Proximity Reader Manual
Page 8
...If the case is opened while the KPR2000 is now the Manager Delete Card. Power the KPR2000 down. 2. ADVANCED PROGRAMMING Alarm TO RESET THE ALARM Programming Step Keystroke Combination To reset the door forced open warning (Read valid card) OR (Master Code #) To reset the door open too long (DOTL)... warning (Read valid card) OR (Master Code) # ANTI-TAMPER ALARM The KPR2000 uses an optical sensor as the input for its ...
...If the case is opened while the KPR2000 is now the Manager Delete Card. Power the KPR2000 down. 2. ADVANCED PROGRAMMING Alarm TO RESET THE ALARM Programming Step Keystroke Combination To reset the door forced open warning (Read valid card) OR (Master Code #) To reset the door open too long (DOTL)... warning (Read valid card) OR (Master Code) # ANTI-TAMPER ALARM The KPR2000 uses an optical sensor as the input for its ...