LevelOne IES-0820 Support and Manuals
Get Help and Manuals for this LevelOne item
This item is in your list!
View All Support Options Below
Free LevelOne IES-0820 manuals!
Problems with LevelOne IES-0820?
Ask a Question
Free LevelOne IES-0820 manuals!
Problems with LevelOne IES-0820?
Ask a Question
Popular LevelOne IES-0820 Manual Pages
Datasheet - Page 1
...setup or con gure required, truly plug and play. Complies with NEMA TS2 Environmental requirements for the demanding industrial environments at mission-critical environment. IES-0820
8 FE Unmanaged Switch -40 to 75, DIN-rail
Overview
LevelOne IES-0820... on and o 6,000 times while loaded, with no single failure.
Supports 10/100Mbps-Full/Half-duplex, Auto-Negotiation, Auto-MDI/MDIX - Complies...
Manual - Page 2
... and use the Industrial Ethernet Switch. In this manual, you will find:
· Features on the switch · Illustrative LED functions · Installation instructions · Specifications
IES-0820 User Manual
Page 1
To get the most out of this manual, you should have an understanding of Ethernet networking concepts. This switch integrates full wire speed switching technology...
Manual - Page 5
... voltage and Max. UL1604 Industrial Control Equipment certified Maximum Surrounding Air Temperature @ 74℃ (165℉). · Supports DIN-Rail or Panel Mounting installation.
current consumption: 0.76A @ 12VDC, 0.38A @ 24VDC,
0.19A @ 48VDC. Power consumption: 9.12W Max. ...℃ to 75℃ (-40℉ to 167℉) operating temperature range. IES-0820 User Manual
Page 4
Manual - Page 7
Physical Ports
This switch provides: Eight 10/100Base-TX ports Eight 10/100Base-TX ports + one 100Base-FX/BX port Six 10/100Base-TX ports + two 100Base-FX/BX ports Four 10/100Base-TX ports + four 100Base-FX/BX ports
Connectivity RJ-45 connectors SC or ST connector on 100Base-FX fiber port SC connector on 100Base-BX fiber port
IES-0820 User Manual
Page 6
Manual - Page 8
...ventilation
holes on each side of the switch.
IES-0820 User Manual
Page 7 Installation
This chapter gives step-by-step instructions about how to install the switch:
Selecting a Site for the ...electromagnetic field (RFC)
standards. · Make sure that the switch receives adequate ventilation. Specifically, the site you should place the switch where it will not be subjected to 75 degrees...
Manual - Page 9
Removal: Pull out the lower edge and then remove the switch from above using the slot.
Installation: Place the switch on the DIN rail from the DIN rail. IES-0820 User Manual
Page 8 Push the front of the switch. DIN Rail Mounting
Fix the DIN rail attachment plate to the back panel of the switch toward the mounting surface until it audibly snaps into place.
Manual - Page 10
... in . Field Wiring Terminal: Use Copper Conductors Only, 60/75℃, 12-24 AWG torque value 7 lb-in case either PWR1 or PWR2 is enabled)
IES-0820 User Manual
Page 9
Manual - Page 11
DC Jack
PW1
DC Jack
12VDC Input
Relay Output 1A @ 24VDC 1. The relay contact close if power falls
IES-0820 User Manual
Page 10 12VDC DC Jack Input (Optional)
Step 1: Connect the supplied AC to DC power adapter to DC power adapter and attach the plug into a ...
Manual - Page 12
... port link is active. Please do not connect any power source to this as a dry contact application to send a signal for power failure detection. IES-0820 User Manual
Page 11 It provides the normally closed output when the power source is broken
On: Enable Port Fault Detection Off: Disable Port Fault Detection Note...
Manual - Page 13
... your network.
Cable Specifications
Speed
Connector
10Base-T ...IES-0820 User Manual
Page 12
Step 5: Once the connections between two end devices are turned off before any installation.
Use appropriate cables that the power is operational. Step 4: Connect one end of port in use. Connecting to Your Network
Cable Type & Length
It is necessary to follow the cable specifications...
Manual - Page 14
...STP Cat. 5 Up to 185℉) 5%-95% non-condensing Hazardous location: Class I, Division 2 group A, B, C & D UL60950-1, EN60950-1, IEC60950-1 FCC Part 15, Class A EN61000-6-3: EN55022, EN61000-3-2, EN61000-3-3
IES-0820 User Manual
Page 13 Specifications
Ethernet Switch
Applicable Standards
Switching Method Forwarding Rate 10Base-T: 100Base-TX: 100Base-FX/BX: Performance
Cable 10Base-T: 100Base...
Manual - Page 15
... Standards) Environmental Test Compliance IEC60068-2-6 Fc (Vibration Resistance) IEC60068-2-27 Ea (Shock) IEC60068-2-32 Ed (Free Fall) NEMA TS1/2 Environmental requirements for traffic control equipment
IES-0820 User Manual
Page 14
Manual - Page 16
...
5
NC
6
Input Receive Data -
7
NC
8
NC
Uplink Port Input Receive Data + Input Receive Data Output Transmit Data + NC NC Output Transmit Data NC NC
IES-0820 User Manual
Page 15 Connector Pinouts
Pin arrangement of RJ-45 connectors:
RJ-45 Connector and Cable Pins
The following table lists the pinout of 10/100Base...
Quick Install Guide - Page 1
... - Package Contents
IES-0820 Quick Installation Guide CD User Manual
IES-0820
Page 2
IES-0820
Page 1
LED Status
LED
...IES-0820
8 FE Unmanaged Switch -40 to 75, DIN-rail
Quick Installation Guide
Overview
LevelOne IES-0820 Industry Ethernet Switch provides 8 ports of port link activity.
High Reliability
All components are built to versions with no setup...
LevelOne IES-0820 Reviews
Do you have an experience with the LevelOne IES-0820 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for LevelOne yet.
Earn 750 points for your review!