LevelOne GEL-2461 Support and Manuals
Get Help and Manuals for this LevelOne item
View All Support Options Below
Free LevelOne GEL-2461 manuals!
Problems with LevelOne GEL-2461?
Ask a Question
Free LevelOne GEL-2461 manuals!
Problems with LevelOne GEL-2461?
Ask a Question
Popular LevelOne GEL-2461 Manual Pages
EU Declaration of Conformity - Page 2
... switch
Brandname LevelOne
Product GEL-2460, GEL-2461. Declaration of Conformity
We, the undersigned, Digital Data Communications GmbH
Address
Zeche-Norm-StraBe 25 44319 Dortmund Germany
Certify and declare under our sole responsibility that this product conforms to the above named standards and regulations.
2014/12/18 The symbol confirms that the following specifications applied...
Manual - Page 1
GEL-2461
24-Port L2 Managed Gigabit Ethernet Switch, 16 Ports SFP User Manual
V1.0
Digital Data Communications Asia Co., Ltd. http://www.level1.com
Manual - Page 8
... port speed and duplex mode settings Supports Full/Half duplex transfer mode for 10 and 100Mbps and Full duplex transfer
mode for 1000Mbps Any port can be enabled or disabled as Full duplex transfer mode for choosing the GEL-2461 24-Port Intelligent Managed Gigabit Switch from levelone technologies co.
The device is...
Manual - Page 9
...through the
console port Prevents concurrent logins from different computers Supports password change Supports online firmware upgrade Supports factory default settings restore Supports configuration backup and restore
1.2 Technical Specification
Item
Specification
Dimension (L × W × H) 440mm × 230mm × 44mm
Ports
8 10/100/1000M...
Manual - Page 10
... humidity, non-condensing
Storage Humidity
5% to 90% relative humidity, non-condensing
Table 1-1 Technical Specification
1.3 Physical Characteristics
1.3.1 Front Panel
As shown in kind. http://www.level1.com
Page 3
For details, please prevail in Figure 1-1, the front panel of GEL-2461
Note
The product pictures shown in Figure 1-1 and Figure 1-2 are for reference only. Figure...
Manual - Page 13
... 2 Remove the adhesive backing from an available port on the Switch support auto MDI/MDI-X feature. Attach the four
rubber feet to the four round recessed areas on the flat surface.
2.3 Connecting Network Devices
To connect network devices to the GEL-2461 Switch, follow these steps: Step 1 Make sure all devices you can...
Manual - Page 14
...off switch. If not, check to a grounded three-prong AC power outlet. 2.4 Connecting the Power
Chapter 2 Hardware Installation
The GEL-2461 Switch will enter the self-test phase. Then plug the other end of the Switch.
http://www.level1.com
Page ... as described in the range 100-240V AC, 50-60Hz. The GEL-2461 Switch does not have an on , it will work with AC power in Table 1-2.
Manual - Page 18
...
It allows you to backup and restore the system configuration, and reset the Switch to factory default settings
Firmware Upgrade It allows you to save your changes. Button Name
Description
Save
Click to upgrade firmware. Clear
Click to restart the Switch. Table 3-2 Description of the idle timeout is 300 seconds. Chapter 3 Logging in and forgets...
Manual - Page 42
...the port will distinguish between tagged frames and untagged frames, and handle them differently. PVID: It specifes the VLAN ID that will be assgined to the Router's LAN Port 5, and PC2 is ... port number. Tag-based VLAN Configuration Example
The configuration steps are as the port's PVID. A GEL-2461 Switch's Port 1 is connected to the Router's LAN Port 1, PC1 (management host) is connected...
Manual - Page 43
Chapter 7 Advanced
Step 2 On the GEL-2461 Switch, add a new tag-based VLAN: VLAN ID is 2, and port members are Port 1 and Port 2.
7.2 RSTP
The Spanning Tree Protocol... network, and create a tree structure of STP, which provides faster spanning tree convergence after a topology change.
7.2.1 RSTP Bridge Settings
Figure 7-10 RSTP Bridge Settings
Priority: It specifies the RSTP bridge priority.
Manual - Page 46
... LACP in a similar fashion.
7.3.2 LACP Settings
Figure 7-12 LACP Settings
Port: It indicates the port number. If you want the Switch to set this key automatically, please leave the default value.... Chapter 7 Advanced
For example, if you want to aggregate Port 2, 3, 4 and 5 on the local GEL-2461 Switch and those on the remote switch together to form a dynamic LAG, you only need to enable LACP on...
Manual - Page 55
...address table.
The switch then forwards any future frames destined for a specific amount of time (defined by learning the source MAC address of the... builds the address table by MAC Address Aging Time), it cannot be manually removed. Initially, the MAC address table is also called MAC/Port binding...number. On the GEL-2461 Switch, static MAC address is empty. The MAC address table ...
Manual - Page 67
... clear all of levelone technologies co. Don't leave the current page during upgrading. 5. To avoid any unexpected error or unrecoverable hardware damage, do not power off
the Switch during upgrading. 6. After the upgrade is strongly recommended that you want to factory default settings before resetting.
9.2 Firmware Upgrade
Figure 9-2 Firmware Upgrade
Firmware Upgrade: Click the Browse...
Manual - Page 69
Appendix A Contact Information
Appendix A Contact Information
If you have any questions regarding the operation or installation of the GEL-2461 Switch, please contact us in any of the following ways. Technical Support Phone: +886-0800-011-110 LEVELONE Forum: http://www.level1.com/ E-mail: support@level1.com
http://www.level1.com
Page 62
Manual - Page 70
......40 Figure 7-14 802.1p Priority Settings 41 Figure 7-15 Port-based Priority Settings 42 Figure 7-16 LAG Settings...43
http://www.level1.com
Page 63 Password Settings 12 Figure 4-2 Setup Wizard - Appendix B Figure Index
Appendix B Figure Index
Figure 1-1 Front Panel of GEL-2461 3 Figure 1-2 Rear Panel of the Switch 4 Figure 2-1 Installing the Switch in a Rack 6 Figure 3-1 Entering...
LevelOne GEL-2461 Reviews
We have not received any reviews for LevelOne yet.