LevelOne IES-0520 Support and Manuals
Get Help and Manuals for this LevelOne item
View All Support Options Below
Free LevelOne IES-0520 manuals!
Problems with LevelOne IES-0520?
Ask a Question
Free LevelOne IES-0520 manuals!
Problems with LevelOne IES-0520?
Ask a Question
Popular LevelOne IES-0520 Manual Pages
Datasheet - Page 1
... 167°F) operating temperature range, tested for Tra c control equipment - Complies with no setup or con gure required, truly plug and play.
such as oil and gas re nery,... Fahrenheit) temperature.
Supports 10/100Mbps-Full/Half-duplex, Auto-Negotiation, Auto-MDI/MDIX - IES-0520
4 FE + 1 MM SC Unmanaged Switch -40 to 75, DIN-rail
Overview
LevelOne IES-0520 Industry Ethernet Switch ...
Manual - Page 1
IES-0520
4 FE + 1 MM SC Unmanaged Switch -40 to 75, DIN-rail
User Manual
v1.00 - 1206
Manual - Page 2
...you will find:
· Features on the switch · Illustrative LED functions · Installation instructions · Specifications
IES-0520 User Manual
Page 1 Preface
This manual describes how to complicated Industrial networking environments. This switch brings the answer to install and use the Industrial Ethernet Switch.
This switch integrates full wire speed switching technology. To...
Manual - Page 5
... and port link failure by relay output 1.5A @ 24VDC. · Operating voltage and Max. IES-0520 User Manual
Page 4 UL1604 Industrial Control Equipment certified Maximum Surrounding Air Temperature @ 74℃ (165℉). · Supports DIN-Rail or Panel Mounting installation.
Product Highlights
Basic Features
· Meets NEMA TS1/TS2 Environmental requirements such as temperature...
Manual - Page 7
Physical Ports
This switch provides: Eight 10/100Base-TX ports Eight 10/100Base-TX ports + one 100Base-FX/BX port Six 10/100Base-TX ports + two 100Base-FX/BX ports Four 10/100Base-TX ports + four 100Base-FX/BX ports
Connectivity RJ-45 connectors SC or ST connector on 100Base-FX fiber port SC connector on 100Base-BX fiber port
IES-0520 User Manual
Page 6
Manual - Page 8
IES-0520 User Manual
Page 7
Do not block the ventilation
holes on each side of the switch · The power outlet should be within 1.8 meters of the switch. Specifically, the site you...standards. · Make sure that the switch receives adequate ventilation. Installation
This chapter gives step-by-step instructions about how to install the switch:
Selecting a Site for the Switch
As with any ...
Manual - Page 9
Push the front of the switch. IES-0520 User Manual
Page 8 Removal: Pull out the lower edge and then remove the switch from above using the slot.
DIN Rail Mounting
Fix the DIN rail attachment plate to the back panel of the switch toward the mounting surface until it audibly snaps into place. Installation: Place the switch on the DIN rail from the DIN rail.
Manual - Page 10
... dead.
Field Wiring Terminal: Use Copper Conductors Only, 60/75℃, 12-24 AWG torque value 7 lb-in case either PWR1 or PWR2 is enabled)
IES-0520 User Manual
Page 9 The relay contact opens if Power1 or Power2 falls 2.
Manual - Page 11
The relay contact close if power falls
IES-0520 User Manual
Page 10 DC Jack
PW1
DC Jack
12VDC Input
Relay Output 1A @ 24VDC 1. Step 2: Connect the power cord to the AC to the receptacle on ...
Manual - Page 12
... power to send a signal for power failure detection. Please do not connect any power source to this as a dry contact application to the switch. IES-0520 User Manual
Page 11
maps to your power supply. Alarms for Power and Port Failure
Step 1: There are two pins on the terminal block are used for...
Manual - Page 13
... power is operational. Step 4: Connect one end of port in use.
IES-0520 User Manual
Page 12 Always ensure that meet your network. Step 3: Consult the previous... between two end devices are turned off before any installation.
Connecting to Your Network
Cable Type & Length
It is necessary to follow the cable specifications below when connecting the switch to a desired device.
Manual - Page 14
Specifications
Ethernet Switch
Applicable Standards
Switching Method Forwarding Rate 10Base-T: 100Base-TX: 100Base-FX/BX: Performance
Cable 10Base...pair UTP/STP Cat. 5 Up to 185℉) 5%-95% non-condensing Hazardous location: Class I, Division 2 group A, B, C & D UL60950-1, EN60950-1, IEC60950-1 FCC Part 15, Class A EN61000-6-3: EN55022, EN61000-3-2, EN61000-3-3
IES-0520 User Manual
Page 13
Manual - Page 15
... Standards) Environmental Test Compliance IEC60068-2-6 Fc (Vibration Resistance) IEC60068-2-27 Ea (Shock) IEC60068-2-32 Ed (Free Fall) NEMA TS1/2 Environmental requirements for traffic control equipment
IES-0520 User Manual
Page 14
Manual - Page 16
...
5
NC
6
Input Receive Data -
7
NC
8
NC
Uplink Port Input Receive Data + Input Receive Data Output Transmit Data + NC NC Output Transmit Data NC NC
IES-0520 User Manual
Page 15 Appendix A - Connector Pinouts
Pin arrangement of RJ-45 connectors:
RJ-45 Connector and Cable Pins
The following table lists the pinout of 10...
Quick Install Guide - Page 1
... IES-0520 Quick Installation Guide CD User Manual
IES-0520
Page 2
Overview
LevelOne IES-0520 Industry Ethernet ...Supports 802.3/802.3u/802.3x. Power consumption: 9.12W Max. Power Supply: Redundant DC Terminal Block power inputs or 12VDC DC JACK
with no setup or configure required, truly plug and play. o This equipment is designed to be non-hazardous. IES-0520...
LevelOne IES-0520 Reviews
We have not received any reviews for LevelOne yet.