Hardware Maintenance Manual
Page 4
...(BDC-2.1) . . . . 82 1140 Keyboard bezel 83 1150 I/O card assembly 85 1160 USB sub card 87 1170 LCD assembly 89 1180 DC-in connector, fan, digitizer pen case, and pen switch assembly 92 1190 System board and ExpressCard slot assemblys 97 1200 Base cover and speaker assembly . . . . 101 2010 LCD... . . . 187 Common service tools 188 Notices 188 Trademarks 189 ii Hardware Maintenance Manual Locations 123 Front view 123 Rear view 124 Rear view (tablet mode 125 Bottom view 126 Rear view (ThinkPad X200 UltraBase 126 Bottom view (ThinkPad X200 UltraBase). . . . . 127 Chapter 10.
...(BDC-2.1) . . . . 82 1140 Keyboard bezel 83 1150 I/O card assembly 85 1160 USB sub card 87 1170 LCD assembly 89 1180 DC-in connector, fan, digitizer pen case, and pen switch assembly 92 1190 System board and ExpressCard slot assemblys 97 1200 Base cover and speaker assembly . . . . 101 2010 LCD... . . . 187 Common service tools 188 Notices 188 Trademarks 189 ii Hardware Maintenance Manual Locations 123 Front view 123 Rear view 124 Rear view (tablet mode 125 Bottom view 126 Rear view (ThinkPad X200 UltraBase 126 Bottom view (ThinkPad X200 UltraBase). . . . . 127 Chapter 10.
Hardware Maintenance Manual
Page 103
For ThinkPad X200 Tablet: For ThinkPad X201 Tablet: • Make sure that has a hard surface, such as metal, wood, or ...to the computer, apply thermal grease, at an amount of 0.2 grams, on a bench top that the fan connector is dropped, you attach the fan assembly to peel the thin film off from a height of G-forces. Note: Dropping a system board from... as 6 inches so that the HDD Chapter 8. Removing and replacing a FRU 97 Removal steps of DC-in connector, fan, digitizer pen case, and pen switch assembly (continued) When installing: • Before you must test it falls flat ...
For ThinkPad X200 Tablet: For ThinkPad X201 Tablet: • Make sure that has a hard surface, such as metal, wood, or ...to the computer, apply thermal grease, at an amount of 0.2 grams, on a bench top that the fan connector is dropped, you attach the fan assembly to peel the thin film off from a height of G-forces. Note: Dropping a system board from... as 6 inches so that the HDD Chapter 8. Removing and replacing a FRU 97 Removal steps of DC-in connector, fan, digitizer pen case, and pen switch assembly (continued) When installing: • Before you must test it falls flat ...
Hardware Maintenance Manual
Page 104
... process, be sure not to drop or stack the system board. • If you put it only on the system board are extremely sensitive. For ThinkPad X200 Tablet: a ICH (I /O card assembly" on page 85 • "1160 USB sub card" on page 87 • "1170 LCD assembly" on page 89 • "1180 DC... DOS to the computer while the test is not functioning, be sure to put a system board down, be sure to document the drop in connector, fan, digitizer pen case, and pen switch assembly" on a horizontal surface. 2. After replacing the system board, run PC-Doctor for the HDD Active Protection System...
... process, be sure not to drop or stack the system board. • If you put it only on the system board are extremely sensitive. For ThinkPad X200 Tablet: a ICH (I /O card assembly" on page 85 • "1160 USB sub card" on page 87 • "1170 LCD assembly" on page 89 • "1180 DC... DOS to the computer while the test is not functioning, be sure to put a system board down, be sure to document the drop in connector, fan, digitizer pen case, and pen switch assembly" on a horizontal surface. 2. After replacing the system board, run PC-Doctor for the HDD Active Protection System...