Lantronix xPico 200 Evaluation Kit Support and Manuals
Get Help and Manuals for this Lantronix item
View All Support Options Below
Free Lantronix xPico 200 Evaluation Kit manuals!
Problems with Lantronix xPico 200 Evaluation Kit?
Ask a Question
Free Lantronix xPico 200 Evaluation Kit manuals!
Problems with Lantronix xPico 200 Evaluation Kit?
Ask a Question
Popular Lantronix xPico 200 Evaluation Kit Manual Pages
Integrating xPico 200 Series with Microsoft Azure - Page 14
....
4. Under IoT Hub Connection String, paste the connection string you obtained
earlier and click Update. STEP 4. Under New-line, set Receive and Transmit to the xPico 200 series device via serial connection on line 1.
2.
Open Device Explorer. 5. Click Setup > Terminal. 3. Test the integration
1. Application Note: Integrating xPico 200 Series with Microsoft Azure
14...
Integrating xPico 200 Series with Microsoft Azure - Page 26
Click Setup > Terminal. 3. Under New-line, set Receive and Transmit to the xPico 200 series device via serial connection on line 1. 2. Open Device Explorer. Test the integration 1. Using TeraTerm, connect to LF ...
Integrating xPico 200 Series with Microsoft Azure - Page 37
... xPico 200 series device via serial connection on line 1. 2. primary key
STEP 6. Using TeraTerm, connect to Connection string - Open Device Explorer.
Test the integration 1. Click Setup > Terminal. 3. Under New-line, set Receive and Transmit to LF and click OK. 4.
Configuring the SNMP Extended Agent for xPico 200 Series and XPort EDGE - Page 6
... TCP connection. The host processor accepts a TCP connection from the xPico 200. General Setup
The host processor connects to the xPico 200 by any physical interface that supports at least one host response per incoming SNMP packet.
let the Lantronix SNMP agent handle it, or b. This will examine each forwarded packet and decide...
Configuring the SNMP Extended Agent for xPico 200 Series and XPort EDGE - Page 9
... or Linux platform. Set the
protocol to TCP and the local port to enable the extended agent.
Figure 3. Figure 3 shows the extended agent demo setup. Enter the Extended ...contact Lantronix Technical Support. c. Load the SNMP enabled SDK rom file into the xPico device. 2. Agent Connected to SNMP and configure the SNMP settings. a. Before you follow the procedure below, install the...
Configuring the SNMP Extended Agent for xPico 200 Series and XPort EDGE - Page 10
...". • host - Options are provided
with the demo zip file. 5. The baud rate setting for serial connections, including RS-232/RS-485, USB, or gSPI. Options are Windows = ... Script Configuration
The host script arguments and configuration settings are supported: Get, Set, Get next, Walk, and V2Traps. Open the MIB browser. Lantronix SNMP agent behavior is expected. At the same...
xPico 200 Series Layer 2 Wi-Fi to Ethernet Bridge - Page 3
... example, the following example uses a standard private LAN/WLAN Layer 3 configuration but the xPico firmware will allow the Layer 2 traffic to send raw Ethernet frames (some video cameras). The following are used : • Two xPico 200 Series Evaluation Kits • Layer 2 Ethernet frame generator
xPico 200 Series Layer 2 Wi-Fi to Ethernet Bridge...
xPico 200 Series - JTAG Programming - Page 3
...Comments
November 2021 A
Initial document. Contents
Overview ...4 Hardware and Software Requirements 4
JTAG Programming Hardware Checklist 4
JTAG Hardware Setup 5 Software Instructions 6
xPico 200 Series -
JTAG Programming
3 Revision History
Date
Rev. For the latest revision of this product document, please check our online documentation at www.lantronix.com/support/documentation.
xPico 200 Series - JTAG Programming - Page 5
... the Tag-Connect grey cable JTAG connector into J1 of the Evaluation Kit as shown in assembly.
2.
xPico 200 Series - JTAG Hardware Setup
Perform the following steps to connect the Olimex and Tag-Connect adapters... (2-pins on one end and 1 on the other end) connection to the xPico 200 Evaluation Kit. 1. Note that mistakes are keyed which will prevent any mistakes in the image
below .
Xpico 200 Firmware Instructions - Page 7
... Series Integration Guide. Jumper or SW hook to the device and the Tera Term macro file. Download the xPico 200 continuous mode certification software from the archive.
xPico 200 Series Certification Firmware Instructions
7
Example Schematic Block Diagram for xPico 200 Test Points
See the evaluation board schematic and artwork for certification, download and install the...
Xpico 200 Firmware Instructions - Page 12
... either antenna 0 or antenna 1. The xPico 200 supports 20Mhz and 40Mhz bandwidth for 802.11n in the chanspec line sets the bandwidth. Transmit Stop Command
wl pkteng_stop tx
The... txant parameter sets the antenna to set the channel using the parameter after the -c parameter and change the chanspec line to set the bit rate.
xPico 200 Series Certification Firmware Instructions
12
The ...
Xpico 200 Firmware Instructions - Page 20
... a specific frequency and sends reports about received packets. modulation_type sets the data pattern to compare received data.
0: 0x00 8-bit pattern
1: 0xFF 8-bit pattern
2: 0xAA 8-bit pattern
3: 0xF0 8-bit pattern
4: PRBS9 pattern
logical_channel sets the logical channel to BR or EDR for the remote Tx device (6 bytes). xPico 200 Series Certification Firmware Instructions
20 Frequency sets the...
xPico 200r Certification Firmware Instructions Application Note - Page 7
... directory with the following contents:
a. xPico® 200 Certification Firmware Instructions
7 Extract the files from https://www.lantronix.com/products/xpico-200/#tab-docs-downloads.
2. xPico200 directory -
b. contains the rom that can be pasted in the xPico 200 Series Evaluation Kit User Guide.
this document. Download the xPico 200 continuous mode software from...
xPico 200r Certification Firmware Instructions Application Note - Page 12
... channel using the parameter after the -c parameter and change the chanspec line to set the bit rate. The xPico 200 supports 20Mhz and 40Mhz bandwidth for 802.11n in the chanspec line sets the bandwidth. xPico® 200 Certification Firmware Instructions
12
802.11n Transmit Script
wl down wl mpc 0 wl phy_txpwrctrl 1 wl phy_watchdog 0 wl...
xPico 200r Certification Firmware Instructions Application Note - Page 19
...0xFF 8-bit pattern
2: 0xAA 8-bit pattern
3: 0xF0 8-bit pattern
4: PRBS9 pattern
logical_channel sets the logical channel to BR or EDR for the remote Tx device (6 bytes).
The device ...Description
This test sets the BT radio to 2480 MHz.
xPico® 200 Certification Firmware Instructions
19 Frequency sets the frequency used to listen from 2402 MHz to receive on a specific frequency and ...
Lantronix xPico 200 Evaluation Kit Reviews
We have not received any reviews for Lantronix yet.