Lantronix XPort Direct Demonstration Kit Support and Manuals
Get Help and Manuals for this Lantronix item
This item is in your list!
View All Support Options Below
Free Lantronix XPort Direct Demonstration Kit manuals!
Problems with Lantronix XPort Direct Demonstration Kit?
Ask a Question
Free Lantronix XPort Direct Demonstration Kit manuals!
Problems with Lantronix XPort Direct Demonstration Kit?
Ask a Question
Popular Lantronix XPort Direct Demonstration Kit Manual Pages
XChip Direct - User Guide - Page 8
... MAC 40 Ethernet connection type 40
Security Settings (Option 6 40
Disable Telnet Setup 41 Disable TFTP Firmware Upgrade 41 Disable Port 77FE (Hex 41 Disable ECHO Ports 41 Enable Enhanced Password 42 Disable Port 77F0 (Hex 42
Default Settings (Option 7 42
Channel 1 Configuration Defaults 42 Expert Settings Defaults 42 Security Settings Defaults 43
8: GPIO Interface
44
Configurable...
XChip Direct - User Guide - Page 10
... and update the XPort™ Direct firmware and is a deployment-ready Device Gateway SoC coprocessor bundled with the XPort Direct firmware.
Details expert and security settings and explains how to reset the unit to assign an IP address. Provides instructions for monitoring the network and diagnosing problems.
DeviceLinx™ XPort Direct/XChip Direct SoC User Guide
10...
XChip Direct - User Guide - Page 11
... information on the product CD and the Lantronix web site (www.lantronix.com).
The Com Port Redirector User Guide explains how to contact Lantronix Technical Support. 1: Using This Guide
Chapter
11: Troubleshooting
A: Alternative Ways to Assign an IP Address B: Binary to Hexadecimal Conversions
Description
Describes common problems and error messages and how to use it . DeviceInstaller...
XChip Direct - User Guide - Page 13
... the specific unit. This address is also referred to the connection arrives correctly at the target. Other supported protocols...Lantronix product. The unit's serial channel (port) can be associated with other devices without maintaining a point-to the serial port. TFTP for firmware updates...Port number 9999 is similar to the unit's Setup (configuration) Mode window. A port number is ...
XChip Direct - User Guide - Page 15
... (Setup Mode) on a network. The installation wizard window displays. 4. The CD automatically starts and displays
the main window. 2. Respond to the installation wizard prompts. DeviceLinx™ XPort Direct/XChip Direct SoC User Guide
15 The installation wizard window displays. 3.
Installing DeviceInstaller
To install DeviceInstaller if your product from the Lantronix...
XChip Direct - User Guide - Page 17
... the XPort Direct's maximum baud rate. Follow the instructions above to categorize the XPort Direct. Name
Group
Comments
Device Family Type ID Hardware Address Firmware Version Extended Firmware Version Online Status
Telnet Enabled Telnet Port Web Enabled Maximum Baud Rate Supported Firmware Upgradeable
IP Address Number of the firmware.
This group name is not visible on other...
XChip Direct - User Guide - Page 18
... default setting is 45. Non-configurable field. Displays False. Non-configurable field. Displays 1-65s, the XPort Direct's TCP keepalive. Non-configurable field. Displays True.
Displays the number of Ports
TCP Keepalive
Supports Configurable Pins Supports Email Triggers Supports AES Data Stream Supports 485 Supports 920K Baudrate
Supports HTTP Server Supports HTTP Setup Supports...
XChip Direct - User Guide - Page 22
...
1
BootP
2
For example, if the third octet is the most common setting when using DHCP. To disable an option, set to assign IP addresses, enter the IP address manually. DeviceLinx™ XPort Direct/XChip Direct SoC User Guide
22 The IP Address, Set Gateway IP Address, and Netmask fields display the current values. only DHCP...
XChip Direct - User Guide - Page 28
6: Setup Mode: Channel Configuration
Table... character
0 0 0 1
With active Modem Control In
0 0 1 0
With a specific start character
0 0 1 1
Manual connection
0 1 0 0
Autostart
0 1 0 1
Hostlist
0 0 1 0
d) ...
Never Accept Incoming Rejects all external connection attempts.
Accept with Modem Mode.
Default setting. DeviceLinx™ XPort Direct/XChip Direct SoC User...
XChip Direct - User Guide - Page 29
...Setup Mode: Channel Configuration
b) Response
Character Response
c) Active Startup
No Active Startup With Any Character With active Modem Control In With a Specific Start Character Manual...command string received from the serial port.
Default setting is 0.0.0.0/0, the XPort Direct enters Monitor Mode...8482; XPort Direct/XChip Direct SoC User Guide
29 Attempts to provide the most significant...
XChip Direct - User Guide - Page 30
... Modem Modes. Each entry contains the IP address and the port number. 6: Setup Mode: Channel Configuration
Figure 6-2.
Hostlist supports a minimum of 1 and a maximum of 12 entries. Hostlist Option
DeviceLinx™ XPort Direct/XChip Direct SoC User Guide
30 Manual Connection Address Example
Command String
C121.2.4.5/1 C5
Result if remote IP is 129.1.2.3 and remote...
XChip Direct - User Guide - Page 34
...set the remote TCP port number for the unit to a host using the unit for login purposes, use the remote port number 23 (Internet standard port number for Telnet services).
Auto Increment Source Port
Auto increment source port (N) ? _
Y (Yes) auto increments the source port.
DeviceLinx™ XPort Direct/XChip Direct SoC User Guide... is attempted.
6: Setup Mode: Channel Configuration
Send...
XChip Direct - User Guide - Page 40
Enter between 512 and 1400 bytes. The default is not specific to the XPort Direct. Enter 0 for TCP and UDP....Manually configured speed/duplex settings only work correctly if the peer or switch also uses a static setting. DeviceLinx™ XPort Direct/XChip Direct SoC User Guide
40 To select the speed and duplex, enter one of Telnet or serial connections. This is a common Ethernet problem...
XChip Direct - User Guide - Page 56
...problem, or possibly, you have entered the Ethernet address incorrectly with the serial device to which it is the wrong serial settings were chosen.
The XPort Direct is not communicating with the ARP command. When you try to enter the setup mode on . DeviceLinx™ XPort Direct/XChip Direct SoC User Guide... no flow control. 11: Troubleshooting
Problem/Message
When you Telnet to port...
XChip Direct - User Guide - Page 57
... X.X.X.X (X.X.X.X is disabled within the XPort Direct security settings.
Technical Support Europe, Middle East, and Africa Phone: +33 (0) 1 39 30 41 72 Email: eu_techsupp@lantronix.com or eu_support@lantronix.com
Firmware downloads, FAQs, and the most up-to-date documentation are unable to fix the error, you report a problem, please provide the following options:
To check our online...
Lantronix XPort Direct Demonstration Kit Reviews
Do you have an experience with the Lantronix XPort Direct Demonstration Kit that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Lantronix yet.
Earn 750 points for your review!