Kenwood TK-D348R Support and Manuals
Get Help and Manuals for this Kenwood item
This item is in your list!
View All Support Options Below
Free Kenwood TK-D348R manuals!
Problems with Kenwood TK-D348R?
Ask a Question
Free Kenwood TK-D348R manuals!
Problems with Kenwood TK-D348R?
Ask a Question
Popular Kenwood TK-D348R Manual Pages
User Manual 1 - Page 4
...do not exist. • Selecting a channel which does not exist causes a continuous error tone to
sound. 1 Set the Channel selector to the highest channel number for channels 2, 4, 6, 8, 10, ...unable to change. 2 Insert the channel stopper. 3 Set the arrow of the transceiver by holding the antenna at channel 1, the knob may not
install correctly and the channel may damage the antenna and degrade...
User Manual 1 - Page 5
Acrylic ester, which is contained in a hot environment. CAUTION
◆◆ Do not use glue which is designed to prevent screw loosening when installing the belt clip, as it before use.
INSTALLING THE BELT CLIP
Belt clip
If necessary, attach the belt clip using the two supplied M3 x 8 mm screws. CAUTION
◆◆...
User Manual 1 - Page 7
INSTALLING THE OPTIONAL SPEAKER/ MICROPHONE (OR HEADSET)
Note: ◆◆ The transceiver is not fully water resistant when using a speaker/ microphone or
headset. 1 Insert the speaker/ ...
User Manual 1 - Page 9
... Side 2 keys can be programmed only on the Selector. Your dealer may have set some keys to continuously increase the Channel number.
9
n Call Interruption Interrupts a ...Note: ◆◆ This function can be held down for a short duration instead of 1.
Ask your dealer
setting. n Call 1/ Call 2 Initiates a call , stopping it from being momentarily pressed. n Channel Up Increases ...
User Manual 1 - Page 10
... Lone Worker Toggles Lone Worker mode ON and OFF. n Priority-channel Select Press this key to set the current channel as the Priority channel. n Low Transmit Power Each channel is off while holding down...the transceiver into Emergency mode.
Note: ◆◆ This function can listen to set the current channel as the Home Channel.
Release this key in normal mode to turn the transceiver ...
User Manual 1 - Page 11
... or from the scan sequence. Note: ◆◆ This function cannot be programmed only on the Selector. n Zone Select Selects the Zone number. Contact your KENWOOD dealer for
further information.
User Manual 1 - Page 12
Enter the password (up to 4 digits) using the following procedure. 1 Set the Selector to position "1". 2 Press the Side 1 or Side 2 key to enter the ...AND CHANNEL
1 Select the desired zone using the Selector (default). • Each channel is programmed with settings for only the number of digits the password contains.
4 Press the PTT switch to check whether or
not the channel is free. • ...
User Manual 1 - Page 13
... call only if the received signal matches your mouth. Receiving Individual Calls
When you can set up on the selected channel, you would during a normal transmission.
Receiving Group Calls
When ...voice. Battery power is low while transmitting Scanning
Receiving an encoded call The Transceiver Password function is programmed.
RECEIVING
Select the desired zone and channel.
• For ...
User Manual 1 - Page 14
... PTT switch to save the setting. • A beep will exit VOX setup mode.
14
VOICE OPERATED TRANSMISSION (VOX)
VOX operation allows you can change this setting for each channel by your ... the transceiver will be turned off for specific channels by selecting a channel with status memory is ON, you are using a supported headset. To activate VOX and set the VOX Gain level, from 1 (least...
User Manual 1 - Page 15
... a Selcall has been received. SELCALL (SELECTIVE CALLING)
A Selcall is a voice call , press the PTT switch and speak into the microphone. Identification Codes
An ID code is a protocol owned by JVC KENWOOD Corporation. To respond to the call to a particular station or to transmit your conversation. Paging Call
1 Select your desired zone and channel...
User Manual 1 - Page 16
..., Scan pauses at least 2 channels added to normal.
SCAN DELETE/ ADD
You can temporarily remove specific channels from your scan list. 1 Select your desired zone and/or channel. 2 Press the key...change to add/remove channels).
16 However, when scanning is ended and
restarted, the Scan settings return to the scanning sequence. While scanning, the transceiver checks for signals on a normal...
User Manual 1 - Page 17
...Worker] to toggle the Scrambler function ON or OFF.
17
Note: ◆◆ Your dealer can set the transceiver to emit a tone when transmitting in on how it is a safety feature built into the...signals as normal, or
mute the speaker during Emergency operation. Lone Worker Mode
Lone Worker Mode is set up by your dealer.
2 To exit Emergency mode, press the [Emergency] key again. •...
User Manual 1 - Page 19
...ringing tone will sound. When you receive a group call and the received group ID matches the ID set Selcall on PTT for Individual or Group calls,
allowing you receive an individual call, a ringing tone ...GROUP CALLS
Each channel is enabled, the Proceed tone will
end. After the tone ends, you can set up on a DMR digital channel. Receiving
When you to the call, the call , press the key...
User Manual 1 - Page 20
... or an operation is released and the LED indicator blinks red when the battery needs recharged or replaced.
Pressing the PTT switch will cause a warning tone to stop the tone.
LOW BATTERY WARNING... flash green when receiving a QT/
DQT signal which does not match the QT/DQT tone/code set up in your dealer, the Battery Saver function decreases the amount of power used to stop ...
Kenwood TK-D348R Reviews
Do you have an experience with the Kenwood TK-D348R that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Kenwood yet.
Earn 750 points for your review!