Kenwood TK-2400 Support and Manuals
Get Help and Manuals for this Kenwood item
This item is in your list!
View All Support Options Below
Free Kenwood TK-2400 manuals!
Problems with Kenwood TK-2400?
Ask a Question
Free Kenwood TK-2400 manuals!
Problems with Kenwood TK-2400?
Ask a Question
Kenwood TK-2400 Videos
Popular Kenwood TK-2400 Manual Pages
Operation Manual - Page 1
INSTRUCTION MANUAL
VHF FM TRANSCEIVER
TK-2400
UHF FM TRANSCEIVER
TK-3400
B62-2478-20 (K)
Operation Manual - Page 2
...VHF (TK-2400) or 90 UHF (TK-3400) operating frequencies and each channel can be set up with a QT tone or DQT code allowing ...settings.
This KENWOOD transceiver is called a "transceiver", meaning "transmitter & receiver".
Treat it with dependable and reliable communications. OPERATING CONDITIONS
Condition
Open locations (no obstructions)
In steel/ concrete reinforced buildings
TK-2400
TK...
Operation Manual - Page 4
... radio frequency energy and, if not installed and used in accordance with your area, call (toll free) 1-800-8-BATTERY (1-800-822-8837).
ATTENTION: The RBRC Recycle seal found to operate this program is made. The RBRC program is an alternative to disposing Li-ion batteries with the instructions, may cause harmful interference unless the...
Operation Manual - Page 6
...Do not touch these locations when replacing the battery pack. • Do... by KENWOOD. • If the die-cast chassis or other transceiver part is damaged, do not
touch the damaged parts. ...by fine and/or imprisonment. ◆ Refer service to qualified technicians only.
iv NOTICES TO...squelch off before installing optional accessories. • The charger is used for...
Operation Manual - Page 7
... electric shock through the earphone and to your ear.
replace only with metal objects, as they may be against traffic laws. Transmitting at gasoline service stations. • Near explosives or blasting sites. • In aircrafts. (Any use of the transceiver must follow the instructions
and regulations provided by the airline crew.) •...
Operation Manual - Page 11
...BASIC OPERATIONS 8 VOICE OPERATED TRANSMISSION (VOX 9 BACKGROUND OPERATIONS 10 CHANNEL SETUP MODE 11 KEY ASSIGNMENT MODE 20 TROUBLESHOOTING GUIDE 25 ALL RESET MODE 26
UNPACKING AND CHECKING EQUIPMENT
Carefully unpack the transceiver...10 1 • Screw (M3 x 8 mm 2 • Warranty card 1 • Instruction manual 1
Note: Refer to "PREPARATION" for accessory installation instructions.
1
Operation Manual - Page 16
... to page 8. ORIENTATION
Microphone Antenna
Speaker
Battery pack
Channel selector Rotate to change the operating channel. • To change the operating frequency or QT/DQT settings of a
channel, refer to "CHANNEL SETUP MODE" on page 11.
Operation Manual - Page 19
...configured to a higher, more sensitive level, louder received signals may cause the transceiver to activate VOX. To activate VOX and set the VOX Gain level, perform the following steps:
1 Connect the headset to the transceiver . • The VOX function does not ...VOX operation allows you to enable or disable the VOX function for the current channel (you are using a supported headset.
Operation Manual - Page 21
CHANNEL SETUP MODE
This transceiver allows you to reprogram each of the channels with different frequencies and QT (Quiet Talk)/ DQT (Digital Quiet Talk) settings. Channel Number
Table Number
Frequency (MHz)
QT/DQT Setting
TK-2400 (K) 4 channel model
1
20
154.4900
67.0 Hz
2
21
154.5150
67.0 Hz
3
1
151.6250
67.0 Hz
4
2
151.9550
67.0 Hz
TK-2400 (K2...
Operation Manual - Page 22
... 9 10 11 12 13 14 15 16
Table Number
Frequency (MHz)
QT/DQT Setting
TK-3400 (K) 4 channel model
2
464.5500
67.0 Hz
8
467.9250
67.0 Hz
9
461.0375
67.0 Hz
10
461.0625
67.0 Hz
TK-3400 (K2) 16 channel model
2
464.5500
67.0 Hz
8
467.9250
67.0 Hz
9
461.0375
67.0... to choose a compatible frequency to FCC regulations, the default values of TK-2400/ TK2300 (VHF) are different from...
Operation Manual - Page 23
...: The transceiver will sound. • Repeat steps 3 to 5 to set up another channel. 6 Turn the transceiver power OFF and then ON again...The transceiver announces "Channel". • Pressing the Side 1 key or Side 2 key will toggle between QT,
DQT, and Channel setup. 3 Press and release the PTT switch, then rotate the Channel
selector to your desired channel. • Upon pressing and releasing the...
Operation Manual - Page 26
... hear a call . You will toggle between QT, DQT, and Channel setup.
3 Press the Side 1 or Side 2 key to select QT or DQT setup. • The transceiver announces "QT" or "DQT", depending on your...A voice announcement will inform you receive a signal that contains a matching QT tone or DQT code. QT/ DQT SETTINGS
Quiet Talk (QT) and Digital Quiet Talk (DQT) are provided in the table on your...
Operation Manual - Page 30
...
Speaker Switch
* To use of the functions listed in the table below. Explanations on the use this function, the Repeater Mode must be activated by Programming Software.
20
Operation Manual - Page 31
... to hold the Side 1 and Side 2 keys until the LED lights
orange and the transceiver announces "Setup". 2 Continue to press and hold the key to be reprogrammed
(either the Side 1 or Side 2...number. 5 Press the PTT switch to save the setting.
• A beep will sound and the transceiver will automatically return to activate the new settings. Note: The transceiver will announce the new Table...
Operation Manual - Page 35
... one.
Cannot talk to match the new QT/ DQT setting.
25 TROUBLESHOOTING GUIDE
Problem
Solution
Cannot turn the transceiver power ON.
• The battery pack may be installed correctly.
Turn on the channel.
• Change the QT/DQT settings. The battery pack life is finished. Recharge or replace the battery pack.
• The battery pack may...
Kenwood TK-2400 Reviews
Do you have an experience with the Kenwood TK-2400 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Kenwood yet.
Earn 750 points for your review!