Instruction Manual
Page 3
...out horizontally. • If the CD center hole or outside rim has burrs, use the CD only after a while, consult your Kenwood dealer. • If you ...CD player of the unit. Called lens fogging, this manual are examples used to make sure that are A-Z 0-9 KDC-MP238/KDC-MP238CR/KDC-MP208) • The illustrations of the CD. • Do not stick tape etc. CDs that cannot be used • CDs that are used . • CDs... the reset button if the disc auto changer fails to operate properly, press the Reset button. Before using this unit for the condensation to play a CD-R or CD-RW ...
...out horizontally. • If the CD center hole or outside rim has burrs, use the CD only after a while, consult your Kenwood dealer. • If you ...CD player of the unit. Called lens fogging, this manual are examples used to make sure that are A-Z 0-9 KDC-MP238/KDC-MP238CR/KDC-MP208) • The illustrations of the CD. • Do not stick tape etc. CDs that cannot be used • CDs that are used . • CDs... the reset button if the disc auto changer fails to operate properly, press the Reset button. Before using this unit for the condensation to play a CD-R or CD-RW ...
Instruction Manual
Page 10
...HR radio. Select the "STANDBY" display. 2 Enter Menu mode Press the [B.BOOST] button for at least 1 second. page 11 "DIM" ON/OFF* Adjusts the brightness of Security Code is reduced because input of the display according to Sets/Resets security code. "CD READ" 1*/2 Sets the CD read mode. KDC-... display AUX during source selection. *Factory setting : Can be set in standby state. : Can be set while Audio file source. 10 | KDC-MP238/CR/KDC-MP208/KDC-138/CR : Can be displayed or referenced. "MENU"/ "MEnU" is poor. "CODE CLR" page 10/11 (Function of your choice. •...
...HR radio. Select the "STANDBY" display. 2 Enter Menu mode Press the [B.BOOST] button for at least 1 second. page 11 "DIM" ON/OFF* Adjusts the brightness of Security Code is reduced because input of the display according to Sets/Resets security code. "CD READ" 1*/2 Sets the CD read mode. KDC-... display AUX during source selection. *Factory setting : Can be set in standby state. : Can be set while Audio file source. 10 | KDC-MP238/CR/KDC-MP208/KDC-138/CR : Can be displayed or referenced. "MENU"/ "MEnU" is poor. "CODE CLR" page 10/11 (Function of your choice. •...
Instruction Manual
Page 11
...or bottom side of the Control knob. Now, you enter the wrong Code in steps 4 through 6, repeat from the battery power source or the Reset button is displayed. Select the "CODE CLR" display. 2 Enter Security Code mode Press the center of the Control knob for at least 1 second. Enter...and reenter the Security Code. Manual Clock Adjustment 1 Select Clock Adjustment mode Press the top or bottom side of the Control knob. Function of KDC-MP238 Deactivating Security Code To deactivate the Security Code function. 1 Select Security Code mode Press the top or bottom side of the Control knob. ...
...or bottom side of the Control knob. Now, you enter the wrong Code in steps 4 through 6, repeat from the battery power source or the Reset button is displayed. Select the "CODE CLR" display. 2 Enter Security Code mode Press the center of the Control knob for at least 1 second. Enter...and reenter the Security Code. Manual Clock Adjustment 1 Select Clock Adjustment mode Press the top or bottom side of the Control knob. Function of KDC-MP238 Deactivating Security Code To deactivate the Security Code function. 1 Select Security Code mode Press the top or bottom side of the Control knob. ...
Instruction Manual
Page 15
... be connected to this unit. The unit may be connected to both the front output terminals or to this unit Kenwood disc changers/ CD players released in 1998 or later can be displayed may have a short-circuit or touched the chassis of disc changers...unit to direct sunlight or excessive heat or humidity. battery. 8. Connect the wiring harness connector to any Kenwood disc changers/ CD players released in the following order: ground, battery, ignition. 5. Press the reset button. 2WARNING If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis...
... be connected to this unit. The unit may be connected to both the front output terminals or to this unit Kenwood disc changers/ CD players released in 1998 or later can be displayed may have a short-circuit or touched the chassis of disc changers...unit to direct sunlight or excessive heat or humidity. battery. 8. Connect the wiring harness connector to any Kenwood disc changers/ CD players released in the following order: ground, battery, ignition. 5. Press the reset button. 2WARNING If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis...
Instruction Manual
Page 18
...audio files. ▲ "CD READ" is set up Display. ▲ (page 12) is played. ➪ ---- 18 | KDC-MP238/CR/KDC-MP208/KDC-138/CR TOC ERR/E-04: ...Something is not extended. ☞ Pull the antenna out all the way. Radio reception is poor. ✔ The car antenna is wrong with a format that...reset button on this unit can play , but another one plays instead. ✔ The specified CD is quite dirty. ☞ Clean the CD. ✔ The disc is loaded in the disc magazine. • The CD is quite dirty. E-05: The disc is upsidedown. IN (Blink): The CD player...
...audio files. ▲ "CD READ" is set up Display. ▲ (page 12) is played. ➪ ---- 18 | KDC-MP238/CR/KDC-MP208/KDC-138/CR TOC ERR/E-04: ...Something is not extended. ☞ Pull the antenna out all the way. Radio reception is poor. ✔ The car antenna is wrong with a format that...reset button on this unit can play , but another one plays instead. ✔ The specified CD is quite dirty. ☞ Clean the CD. ✔ The disc is loaded in the disc magazine. • The CD is quite dirty. E-05: The disc is upsidedown. IN (Blink): The CD player...