Kenwood KAC-X621 Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood KAC-X621 manuals!
Problems with Kenwood KAC-X621?
Ask a Question
Free Kenwood KAC-X621 manuals!
Problems with Kenwood KAC-X621?
Ask a Question
Most Recent Kenwood KAC-X621 Questions
What Year Was The Kenwood Kac-x621 Amp Made
(Posted by outlawstreetrace 11 years ago)
Popular Kenwood KAC-X621 Manual Pages
Instruction Manual - Page 1
KAC-X621 KAC-PS621 KAC-X521 KAC-PS521
STEREO/BRIDGEABLE POWER AMPLIFIER
INSTRUCTION MANUAL
© B64-2798-00/00 (MV)
Instruction Manual - Page 2
...AMP Control are going to be connected should be working right, consult your Kenwood dealer.
If the "E-02" code does not disappear, contact your unit to malfunction. • To prevent a short circuit when replacing...install a protective fuse in the Operation Manual ... the ground wire to a metal part of the speakers and then connect suitable speakers to the amplifier.
4Ω 4 Ω
4&#...
Instruction Manual - Page 3
... fan and ducts of the unit are large variety of settings and connections possible according to applications, read the instruction manual well to decrease the internal temperature. Otherwise heat build-up occurs and the unit may cause injury or an accident. • After installing the unit, check to make sure that are sensitive to...
Instruction Manual - Page 4
...2 Master amplifiers to 7 Slave amplifiers.
You must connect any switch.
• If the fuse blows, check wires for shorts, then replace the fuse...before changing the setting of any of the Master amplifier to the Center Unit.
• The LX AMP and the ... parts
2WARNING
To prevent fire caused by the Center Unit.
��
��
��
Slave amplifier ...
Instruction Manual - Page 5
... lead attached, connect the ground lead to this terminal.
7 ID NUMBER switch Sets an amp identification number (ID) to Slave amplifiers.
0 RESET button Resets the microprocessor of 4Ω or greater.
English 5 ��
Controls
KAC-X521/ KAC-PS521
KAC-X621/ KAC-PS621
�
� ��
�
�
��
� �...
Instruction Manual - Page 6
..." items are displayed.
3 Adjust the Menu item
Press the [2] or [3] button. To call the Amplifier Control's values, hold down the [2] button 3 or more seconds during ID number display ("AMP"). The setup items are displayed approximately 1 second first, then the set values are displayed repeatedly. NOTE
Volume offset value can recall the value when message...
Instruction Manual - Page 7
... be displayed on the Center Unit
When you amplify the same frequency as follows. If the error message continues, consult to the speaker's output. The set item and value operation buttons by following the 'AMP Control' procedure given on the display indicates the amp's ID number.
"AMP × E-03"/"AMP × COND E-03"
When the speaker cord...
Instruction Manual - Page 8
... close as possible to 331.25 (µF) and the coil rating should be as close as possible to 5.3 (mH).
2CAUTION
• If you wish to set a crossover frequency of 120 Hz using a coil and capacitor...in a drop of Frequency (Hz) R=Speaker Impedance (Ω)
Example: When it is required to bridge-connect...
Instruction Manual - Page 9
... use lower volume. • After check the speaker cord and fixing the cause of the short,
replace the fuse. • Adjust the control correctly referring to Noise Ratio...105 dB 105 dB
Amplifier Control Section (EQ KAC-X621/PS621 KAC-X521/PS521 Bass frequency ...60 / 80 / 100 / 200 Hz 60 / 80 / 100 / 200 Hz Bass level...
Kenwood KAC-X621 Reviews
We have not received any reviews for Kenwood yet.