Instruction Manual
Page 2
... are expressly approved in the instruction manual. The protective fuse should be used, use a new one set of speakers are going to be 2Ω or greater (for stereo connections), or 4Ω or greater (for this unit and your Kenwood dealer. The user could lose the authority to operate...'s negative - NOTE • If you experience problems during use a vehicle type (fireproof ) power wring cord with a current capacity greater than the unit's fuse capacity. (Use a power wiring cord with a hard cloth or a cloth dampened by each of the battery wire. • Do not allow the wire ...
... are expressly approved in the instruction manual. The protective fuse should be used, use a new one set of speakers are going to be 2Ω or greater (for stereo connections), or 4Ω or greater (for this unit and your Kenwood dealer. The user could lose the authority to operate...'s negative - NOTE • If you experience problems during use a vehicle type (fireproof ) power wring cord with a current capacity greater than the unit's fuse capacity. (Use a power wiring cord with a hard cloth or a cloth dampened by each of the battery wire. • Do not allow the wire ...
Instruction Manual
Page 4
... power off and check connections. • Be sure to turn the power off before changing the setting of any switch. • If the fuse blows, check wires for this unit to appropriate speaker connectors separately. Do not remove caps from unconnected wires or connectors to prevent short circuits. ...; Do not connect cables and leads to both RCA cable input jacks and the speaker level input terminals simultaneously, for shorts, then replace the fuse with one of the car can cause this may cause malfunction or damage. * Commercially available parts ■ RCA cable or Speaker level input ...
... power off and check connections. • Be sure to turn the power off before changing the setting of any switch. • If the fuse blows, check wires for this unit to appropriate speaker connectors separately. Do not remove caps from unconnected wires or connectors to prevent short circuits. ...; Do not connect cables and leads to both RCA cable input jacks and the speaker level input terminals simultaneously, for shorts, then replace the fuse with one of the car can cause this may cause malfunction or damage. * Commercially available parts ■ RCA cable or Speaker level input ...
Instruction Manual
Page 5
... OUT terminal These jacks output respectively the signals input to this may be amplified by combining the switches and functions described in the following. 1 Fuse (40 A) NOTE If you can be connected should have an impedance of no less than 40 W. • Do not connect the speaker ...cover. One amplifier is a 4 channel amplifier including 2 stereo amplifiers in the instruction manual of amplifiers A and B can 't find the specified capacity fuse at your store etc., consult your Kenwood dealer. 2 Battery terminal 3 Ground terminal 4 Power control terminal Controls the unit ON/OFF.
... OUT terminal These jacks output respectively the signals input to this may be amplified by combining the switches and functions described in the following. 1 Fuse (40 A) NOTE If you can be connected should have an impedance of no less than 40 W. • Do not connect the speaker ...cover. One amplifier is a 4 channel amplifier including 2 stereo amplifiers in the instruction manual of amplifiers A and B can 't find the specified capacity fuse at your store etc., consult your Kenwood dealer. 2 Battery terminal 3 Ground terminal 4 Power control terminal Controls the unit ON/OFF.
Instruction Manual
Page 7
...the following table for possible problems. PROBLEM No sound. (No sound from one side.) (Blown fuse.) The output level is pinched by referring to . of the short, replace the fuse. • Adjust the control correctly referring to . • Connect them properly checking the +...90 Hz) (B channel) ...+6 dB 5 Hz - 50 kHz 0.2 V 5.0 V 10 kΩ ≤100 dB 50 - 200 Hz (variable) 50 - 200 Hz (variable) +6 dB General ...KAC-8452 KAC-8402 Operating Voltage ...14.4 V (11 - 16 V allowable) 14.4 V (11 - 16 V allowable) Current Consumption ...40 A 40 A Installation Size (W × H × D) ...380...
...the following table for possible problems. PROBLEM No sound. (No sound from one side.) (Blown fuse.) The output level is pinched by referring to . of the short, replace the fuse. • Adjust the control correctly referring to . • Connect them properly checking the +...90 Hz) (B channel) ...+6 dB 5 Hz - 50 kHz 0.2 V 5.0 V 10 kΩ ≤100 dB 50 - 200 Hz (variable) 50 - 200 Hz (variable) +6 dB General ...KAC-8452 KAC-8402 Operating Voltage ...14.4 V (11 - 16 V allowable) 14.4 V (11 - 16 V allowable) Current Consumption ...40 A 40 A Installation Size (W × H × D) ...380...