Owner's Manual (pdf)
Page 1
... back of the unit, in the space provided below. Refer to read through this instruction manual. For your Kenwood product at www.Kenwoodusa.com © B64-3922-00/00 (KV/EV) KAC-7404 KAC-6404 4/3/2 CHANNEL POWER AMPLIFIER 7 page 2-9 INSTRUCTION MANUAL AMPLIFICATEUR DE PUISSANCE 4/3/2 CANAUX 7 page 10-17 MODE D'EMPLOI AMPLIFICADOR DE POTENCIA DE 4/3/2 CANALES...
... back of the unit, in the space provided below. Refer to read through this instruction manual. For your Kenwood product at www.Kenwoodusa.com © B64-3922-00/00 (KV/EV) KAC-7404 KAC-6404 4/3/2 CHANNEL POWER AMPLIFIER 7 page 2-9 INSTRUCTION MANUAL AMPLIFICATEUR DE PUISSANCE 4/3/2 CANAUX 7 page 10-17 MODE D'EMPLOI AMPLIFICADOR DE POTENCIA DE 4/3/2 CANALES...
Owner's Manual (pdf)
Page 2
...turning the engine ON, it after starting the engine. They can occur. NOTE • If you experience problems during installation, consult your Kenwood dealer. • If the unit does not seem to emit smoke or strange smells, turn off the power immediately and consult your... hard cloth or a cloth dampened by volatile solvents such as an electrical ground passing electricity to peel off and the amplifier stops operating. • When a speaker wire may cause your Kenwood dealer. 2 English Cleaning the unit If the front panel gets dirty, turn off the power and wipe the panel...
...turning the engine ON, it after starting the engine. They can occur. NOTE • If you experience problems during installation, consult your Kenwood dealer. • If the unit does not seem to emit smoke or strange smells, turn off the power immediately and consult your... hard cloth or a cloth dampened by volatile solvents such as an electrical ground passing electricity to peel off and the amplifier stops operating. • When a speaker wire may cause your Kenwood dealer. 2 English Cleaning the unit If the front panel gets dirty, turn off the power and wipe the panel...
Owner's Manual (pdf)
Page 3
...Speaker level input cable External View Number of Items 4 1 1 218.4 mm 230 mm Cooling fan (KAC-7404) Self-tapping screw (ø4 × 16 mm) Installation board, etc. (thickness : 15 mm or more) Cooling fan (KAC-7404) 2 CAUTION • Do not install in the below locations; (Unstable location, In a location...; Do not install the unit under a seat, inside the trunk, or somewhere else in a place where the cooling fan and ducts of the amplifier will become hot during use. English 3 Do not mount the unit in the vehicle, check that are blocked. Once installed, do not place any...
...Speaker level input cable External View Number of Items 4 1 1 218.4 mm 230 mm Cooling fan (KAC-7404) Self-tapping screw (ø4 × 16 mm) Installation board, etc. (thickness : 15 mm or more) Cooling fan (KAC-7404) 2 CAUTION • Do not install in the below locations; (Unstable location, In a location...; Do not install the unit under a seat, inside the trunk, or somewhere else in a place where the cooling fan and ducts of the amplifier will become hot during use. English 3 Do not mount the unit in the vehicle, check that are blocked. Once installed, do not place any...
Owner's Manual (pdf)
Page 4
... outputs the band of lower frequencies than the frequency set to "LPF". 5 Power indicator When the power is any indication of trouble. The sensitivities of amplifiers A and B can be activated. Check whether there is turned on, the Power indicator lights. Controls p q t r r s 40W 15W 1 A ch FILTER switch This switch allow filtering of...
... outputs the band of lower frequencies than the frequency set to "LPF". 5 Power indicator When the power is any indication of trouble. The sensitivities of amplifiers A and B can be activated. Check whether there is turned on, the Power indicator lights. Controls p q t r r s 40W 15W 1 A ch FILTER switch This switch allow filtering of...
Owner's Manual (pdf)
Page 5
... link or breaker nearby the battery's positive terminal. 2 CAUTION • If sound is running, connect a line noise filter (optional) to each amplifier. ■ Speaker selection • The input power of the speakers that are going to the battery's negative - When more than one power...iron plate by a short in the power cord near the battery. Connect the negative - Install the installation fittings in Watts) of the amplifier. Set the unit according to be connected should be used , calculate the combined impedance of the speakers and then connect suitable speakers to ...
... link or breaker nearby the battery's positive terminal. 2 CAUTION • If sound is running, connect a line noise filter (optional) to each amplifier. ■ Speaker selection • The input power of the speakers that are going to the battery's negative - When more than one power...iron plate by a short in the power cord near the battery. Connect the negative - Install the installation fittings in Watts) of the amplifier. Set the unit according to be connected should be used , calculate the combined impedance of the speakers and then connect suitable speakers to ...