JVC LM170 - 17" LCD Monitor Support and Manuals
Popular JVC LM170 Manual Pages
Instructions - Page 1
ENGLISH
LCD DISPLAY MONITOR
LM-170 LM-150
INSTRUCTIONS
The illustration of the monitor is of LM-170.
Instructions - Page 4
... on a table with casters, lock the casters to high temperature, as possible.
When installing the monitor on other hazards.
To avoid overheating, keep enough space around the monitor (see diagram below).
Refer all service to prevent shock. The illustration of the monitor is of fire or electric shock.
• Use only the accessory cord designed...
Instructions - Page 5
... operation of any service or repairs to this product, ask the service technician to perform safety...instructions have fallen on bed, sofa, rug, or similar surface. It should never be sure the service technician has used replacement parts specified by placing the product on the product. e) If the product has been dropped or damaged in performance-for ventilation.
Do not install...
Instructions - Page 8
...size and position can be manually adjusted. (☞ "SIZE/POSI. Pushing the button left or right.
6 MENU button Displays the MAIN MENU.
☞ page 13
To display the SET-UP MENU: Press the ... Features
7 Front panel
1
2 3 45 6 7
The illustration of the monitor is of LM-170.
1 Speaker (Monaural) (LM-170 only) Outputs the audio signal of the adjustment bar can be changed . (☞ "ADJ.
Instructions - Page 9
... status display When "STATUS DISPLAY" is set to "ON" (☞ page 16), the status (information of the current input and the monitor settings) is displayed for a noncompliant computer signal input.
3 Setting of SCAN SIZE
☞ "7 SCAN SIZE button/lamp" on .
ENGLISH
8
9p
The illustration of the monitor is of LM-170.
8 INPUT SELECT buttons/lamps
Select an...
Instructions - Page 10
... monitor to be controlled by shortcircuiting the pin terminal in this terminal or by inputting the pulse signal.
☞ "How to Use the External Control" on page 17
4 DVI-D terminals
e AUDIO terminal (stereo mini jack)* Input terminal for the analog RGB signals.
6 Security slot Install a security wire to this slot.
* Equipped on LM-170...
Instructions - Page 11
... monitor is of LM-170.
7 Using the monitor on the stand
You can place the monitor in the following two ways when using the monitor ...parts. • Make sure to lift the stand up by 90° and place the monitor as illustrated below .
otherwise
the monitor may fall over. • When the monitor is attached to the higher position of the stand (see below .
ENGLISH
Installation...
Instructions - Page 12
...; Detach the stand first. (☞ page 11) • Ask your dealer to install. not supplied). Installation (cont.)
7 Installing the monitor on the rack
Use a JVC's RACK MOUNT ADAPTER (RK-C157L1G; VESA mounting holes (See page 21 for the specifications of the mounting holes.)
7 Installing the monitor on the wall
Use a commercial wall mounting unit compliant with the VESA...
Instructions - Page 13
.... ADJ. MAIN MENU
Select
ENGLISH
Operation guide Shows the buttons for each input. Setting value: 4:3, 16:9
NOTE: •...for daily use. Setting value: OFF, NORMAL, HARD
ASPECT
Selects the aspect ratio. ADJ. (RGB)" (☞ page
15) manually when you cannot ... Setting value: 00 - 25
SHARPNESS
Adjusts the clearness of the display. Select "all the settings and adjustments of the monitor ...
Instructions - Page 16
...-hour unit. • The hour is reset to "000" after the total hours of use . CONTROL LOCK
Turns on (or off the monitor -
NOTE: • The hour is activated:
- Setting value: MAKE (make contact system), TRIG. (trigger system)
NO SYNC FUNCTION Selects the screen status when no signal is being input.
Displaying...
Instructions - Page 18
...problem, unplug the monitor and consult a JVC-authorized dealer or service center for assistance.
Turn on
"OTHERS" or "Out of the computer) is
specification?
Or, perform "all reset" in the SET...the white balance setting been changed ? in "PICTURE SUB ADJ."
If none of the connected component and set correctly. Problems
Points to the monitor. No sound (LM-170 only) Wrong ...
Instructions - Page 19
... the graphic board
installed into your computer (the driver is not malfunction.
POSI./V. For some signals, the picture cannot be missing or constantly lit.
Or, set the monitor to select "OVER." Press the SCAN SIZE button to the standard display.
• Recommended display setting:
1280 x 1024, 60 Hz (LM-170)
1024 x 768, 60 Hz (LM-150)
Reference pages...
Instructions - Page 20
Specifications
Model
LM-170
LM-150
Type
LCD Display Monitor
LCD panel
17", active matrix TFT
15", active matrix TFT
Effective Screen Size
Width: ...56 Hz - 75 Hz
H: 31.5 kHz - 60 kHz V: 56 Hz - 75 Hz
* Some signals within this manual have been exaggerated, abbreviated or compounded for identification purposes only, and may not be the trademarks
or registered trademarks of their ...
Instructions - Page 21
ENGLISH
135 (5 3/8) 100
7 Dimensions
Unit : mm (inch)
LM-170
Front View
374 (14 3/4)
Side View
70.5 (2 7/8) 28.5 (1 1/8)
Rear View (without the stand)
100
334 (13 1/4) 373.6 (14 3/4)* / 338.6 (13 3/8)**
280 (11 1/8) * at the higher position ** at the lower position
LM-150
Front View
342 (13 1/2)
184 (7 1/4)
VESA mounting holes (Size: M4, depth: 10 mm...
Instructions - Page 22
... listed signals is displayed in "SIZE/POSI. Specifications (cont.)
Specification of the RGB terminal (D-sub 15-pin)
Pin No. Input signal 1 T.M.D.S Data 2- 2 T.M.D.S Data 2+
17
24
3 T.M.D.S Data 2/4 shield 4 NC
5 NC
6 DDC Clock
7 DDC Data
8 NC
Pin No. Preset signals
Signal name
VGA
SVGA
XGA SXGA (LM-170 only) US TEXT Macintosh
Screen resolution 640 x 350...
JVC LM170 Reviews
Do you have an experience with the JVC LM170 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for JVC yet.
Earn 750 points for your review!