JVC LM-150U - 15" LCD Monitor Support and Manuals
Get Help and Manuals for this JVC item
Popular JVC LM-150U Manual Pages
Instruction Manual - Page 4
... interference to which the receiver is operated. • The safety and operating instructions should be retained for its installation, use . • All the safety and operating instructions should be regulated in accordance with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. If this product, observe the following measures...
Instruction Manual - Page 6
...falling over.
• Do not use . The main power supply for the product is distorted. (LM-170A only)
• Do not use this causes condensation, which may become hot during use the ...against the product. • Do not hang on the product when installing the
product on other hazards. Refer all service to qualified service personnel.
• Do not put heavy objects on the product. ...
Instruction Manual - Page 7
... liquid of any service or repairs to . a) ...service personnel. Do not install this product in the following conditions, 1. Unplug this product, ask the service technician to perform safety checks to soot or steam,
such as near the cooking counter or a humidifier • near heat sources • where condensation easily occurs, such as they may be hazardous.
• When replacement parts...
Instruction Manual - Page 8
... scratches, be careful about collection point and recycling of this product, please contact your local municipal office, your household waste disposal service or the shop where you wish to dispose of this product.
If a vacuum cleaner is only valid in accordance with a ... intakes (all the openings). By disposing of this product, please visit our web page www.jvc-europe.com to the product.
Instruction Manual - Page 10
... the selected function.
5 Volume control button (LM-170A only)*2 While the menu is selected, horizontal/vertical size and position can be manually adjusted. (+ "SIZE/POSI.
on the top...OVER = 100% = USER = (back to the beginning) NOTE: • Memorized for the current input or setting. • The position of the button: • Goes to select the mode, then adjust the value (-25...
Instruction Manual - Page 11
...; "NO SYNC" is displayed when no video signal is input. • When "COLOR SYSTEM" is set to "AUTO" (+ page 13), "OTHERS" is displayed for a noncompliant video signal input. • "Out of... signal input.
3 Setting of SCAN SIZE
+ "7 SCAN SIZE button/lamp" on . DVI:
Selects the video signal input to display. ENGLISH
8
9p
The illustration of the monitor is of LM-170A.
8 INPUT SELECT...
Instruction Manual - Page 15
...manually when you cannot get a good picture quality with "AUTO," select "NTSC" or "PAL." Setting value: OFF, NORMAL, HARD
ASPECT
Selects the aspect ratio. all reset
Restores all the settings and adjustments of the display. Setting... in "SIZE/POSI. Setting value: 00 - 25...(+ page 16) and the settings of the luminance signal. Adjusts...input from the computer. Setting value: 4:3, 16:9...
Instruction Manual - Page 16
.... Those items are input from the computer
Select
Adjust
NOTE: • The menu automatically disappears in 2)
Perform "reset"
Select Adjust
7 SIZE/POSI. SET-UP MENU 7 PICTURE SUB ADJ. Operation guide Shows the buttons for the current input or the current input signal. • "HOUR METER X100h" shows the total hors of use...
Instruction Manual - Page 17
...:9)*1
Adjusts the vertical picture size (for 4:3 aspect ratio).
-40 - 00 - +40
V. POSI. (16:9)*1
Adjusts the vertical picture position (for each color (R/G/B). This item is set to the factory settings. R DRIVE
Adjusts the drive level of the picture. HIGH (9300), LOW (6500), USER1, USER2
-40 - 00 - +40 -40 - 00 - +40 -40 - 00 - +40...
Instruction Manual - Page 18
... reset to "000" after signals stop coming in 100-hour unit. • The hour is set to disable the buttons on the screen. HOUR METER X100h
Shows the total hours of the MAKE...8226; Use time less than 1 hour is being input.
NO SYNC DISPLAY Sets the screen status when no signal is not accumulated.
16 Setting value: MAKE (make contact system), TRIG. (trigger system)
NO SYNC FUNCTION...
Instruction Manual - Page 19
... input to DVI 4 Changes the input to RGB 5- 6 Changes ASPECT to 16:9 7 External control 8 GND
Opening Invalid Invalid Invalid Invalid - from "REMOTE SYSTEM" in the SET-UP MENU. + "REMOTE SYSTEM" on page 16
NOTE: • When using the buttons on the front panel or the menu.)
7 How to use the buttons...
Instruction Manual - Page 20
... to the monitor's Check if the input signal format is
specification?
No sound (LM-170A Is the signal cable disconnected? Wrong color, no color
Has the picture adjustment been changed ? Or, adjust "CONTRAST" or "BRIGHT" in the MAIN MENU. Troubleshooting
Solutions to common problems related to your monitor are described here.
Turn on ? Is...
Instruction Manual - Page 21
... the SCAN SIZE button been pressed?
Set it to "ON"? current input or the current input signal do not function. Disable the external control. The following symptoms are problems only when pictures or sounds are a normal characteristic of the graphic board
installed into your computer (the driver is
specification? This is due to be missing...
Instruction Manual - Page 22
Specifications
Model
LM-170A
LM-150A
Type
LCD Display Monitor
LCD panel
17", active matrix TFT
15", active ...slightly.
* Dimensions and weight are approximate. * Design and specifications are subject to change without notice. * All company names and product names mentioned herein are used in this manual have been exaggerated, abbreviated or compounded for identification purposes only...
Instruction Manual - Page 24
...Specification of the RGB terminal (D-sub 15-pin)
Pin No. Input signal 1 T.M.D.S Data 2-
2 T.M.D.S Data 2+
17
24
3 T.M.D.S Data 2/4 shield 4 NC
5 NC
6 DDC Clock
7 DDC Data
8 NC
Pin No. Preset signals
Signal name
VGA
SVGA
XGA SXGA (LM... following computer signals can be displayed on the monitor. does not solve the problem, adjust the items in
wrong position or size
If "AUTO ADJ." ADJ....
JVC LM-150U Reviews
We have not received any reviews for JVC yet.