JVC DLA-M2000SC - 2000 Lumen Projector Less Lens Support and Manuals
Get Help and Manuals for this JVC item
View All Support Options Below
Free JVC DLA-M2000SC manuals!
Problems with JVC DLA-M2000SC?
Ask a Question
Free JVC DLA-M2000SC manuals!
Problems with JVC DLA-M2000SC?
Ask a Question
Popular JVC DLA-M2000SC Manual Pages
Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA projectors (PDF, 379KB) - Page 5
...43H) 'D' (44H) 'E' (45H) 'F' (46H)
* Factory set ID is used when assigning all connected Projector units for information) to the Projector
4.2 Projector to Projector
Character '!' '?' This means that tally (response) data is not ... 26 Internal error data
Definition
5. ４．HEADER
Indicates the beginning and type of the 16 assignable numbers (from the projector when the global...
Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA projectors (PDF, 379KB) - Page 10
...and processing terminated
8.1.2 Status when Error Occurs (Error Status)
Character
HEX
Definition
'A00'
41H 30H 30H Command not supported
'A01'
41H 30H 31H ...setting
Command cannot be accepted if no signal.
'A0A' 'A0B'
41H 30H 41H 41H 30H 42H
Time-out occurred with the communication with sub microcomputer
Error occurred with the communication with the ID-number registered to the Projector...
Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA projectors (PDF, 379KB) - Page 13
...unit automatically enters the Standby mode.
10.4
Emergency Mode This mode is engaged when the projector malfunctions or is turned OFF. The lamp and the fans are rotated continuously during this mode...are rotated continuously to cool down the lamp. The DLA-M2000 series, the Cool-Down Mode time is approximate 90 seconds.
Switch ON the projector's MAIN POWER
After 90 sec. The lamp is...
Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA projectors (PDF, 379KB) - Page 15
This is the default setting. ◇ "CTLR" refers to transmissions from the external control unit and "DLA" refers to transmissions (Tally (Response) Data) from the Projector. ◇ "Reply Time" refers to 7. Parameters. ◇ Acceptance or non-acceptance of Tally (Response) Data. COMMANDS
This section describes the commands that the external control ...
Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA projectors (PDF, 379KB) - Page 23
...;Video Sources (Areas)
Operation mode Standby mode Power ON mode Cool-down mode Emergency mode
X
O
X
X
# Communication Examples
◇ When specifying "2" (decimal) as the sharpness
CTLR DLA
'!' '1' SP 'U08' SP '0002' CR '@' '1' SP '0' CR
◇ When requesting current sharpness adjust level data (if sharpness adjust level is...
Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA projectors (PDF, 379KB) - Page 26
...
Operation mode Standby mode Power ON mode Cool-down mode Emergency mode
X
O
X
X
# Communication Examples
◇ When specifying "MIDDLE" as the color temperature
CTLR DLA
'!' '1' SP 'U0B' SP '1' CR '@' '1' SP '0' CR
◇ When requesting current color temperature data (if color temperature is set to "LOW")
CTLR DLA
'?' '1' SP 'U0B' CR '@' '1' SP '0' SP '0' CR
25
Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA projectors (PDF, 379KB) - Page 30
...mode, the Projector enters the cool-down mode Emergency mode
O
O
X
X
# Communication Examples ◇ When turning the Projector's power ON
CTLR DLA
'!' '1' ...Projector returns the Tally (Response) Data after completing all the POWER ON processing operations (lighting lamp, rotating fans, transmitting data, etc.). If it takes more time to light up or re-try is done due to internal error...
Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA projectors (PDF, 379KB) - Page 33
...
X
The "Sleep time" function automatically turns off the projector power if the no-signal status continues for a specified time.
*Available parameters
Sleep time can be set to "0 min".
#Tally (Response) data format to current... when the time is 3 min.)
CTLR DLA
'?' '1' SP 'U12' CR '@' '1' SP '0' SP '000F' SP '0003' CR
32 and the remaining time is set to "15 min." When the above times...
Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA projectors (PDF, 379KB) - Page 41
12.25 ID :'U1D'(55H 31H 44H)
Definition
：Sets the ID for the Projector
Command Parameter type Reply time Conditions
：'U1D'(55H 31H 44H) ：Special parameter... ID number.
# Communication Examples
◇ When changing the ID to '7' from the current setting of '1'
CTLR DLA
'!' '1' SP 'U1D' SP '7' CR '@' '7' SP '0' CR
Tally (Response) data is returned with New ID no.
40
Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA projectors (PDF, 379KB) - Page 43
... OFF parameter for ON/OFF.
◇ Quick alignment parameter Character
HEX
OFF
'0'
30H
The Projector performs quick alignment processing after waiting for fixed time (about 3 seconds or more).
# Communication...
More than 3 sec Possible to transmit next command
CTLR '!' '1' SP 'U2A' SP '0' CR
DLA
'@' '1' SP '0' CR
'?' '1' SP 'Z03' CR
42
Therefore, after OFF command transmission, send...
Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA projectors (PDF, 379KB) - Page 47
...is 643/10 = 64.3kHz.
46 Horizontal Frequency of data to be returned from Projector. 12.31 Horizontal Frequency Query :'U3C'(55H 33H 43H)
Definition
：Requests horizontal...# Communication Examples
◇ When requesting horizontal frequency (if horizontal frequency is 64.3kHz)
CTLR DLA
'?' '1' SP 'U3C' CR '@' '1' SP '0' SP '0283' CR
Note) Horizontal Frequency is 10 times of Projected ...
Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA projectors (PDF, 379KB) - Page 52
...ON command cannot be sent.
# Communication Examples
◇ When requesting the current operation mode(if the Projector is in the standby mode)
CTLR DLA
'?' '1' SP 'Z03' CR '@' '1' SP '0' SP '0000' CR
51 12.36 Operation... ON command should be accepted in the Power ON mode, the Projector first enters the Cool-Down mode, then automatically enters the Standby mode. (For information on each ...
Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA projectors (PDF, 379KB) - Page 53
... 35H)
Definition
：Asks for the Source (Area) setting actually assigned on the Projector (if Computer Sources is actually assigned)
CTLR DLA
'?' '1' SP 'Z05' CR '@' '1' SP '0' SP 'F0' CR
52 Command Parameter type Reply time Conditions
：'Z05'(5AH 30H 35H) ： (Refer to 11.1 Projector Sources and Source Numbers.) ：3seconds ：Query...
Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA projectors (PDF, 379KB) - Page 54
... 41H)
Definition
：Obtains projector model and software version information.
MMMMMMMXXXXX
Software version Model
Model 'D03 M2000――'
HEX 44H 30H 33H 2DH 2DH 2DH 2DH 4DH 32H 30H 30H 30H 2DH 2DH
Definition DLA-G3010 Series Projector DLA-M2000 Series Projector
# Communication Example
◇ When the projector is a M2000 series projector with software version 1.2.1
CTLR...
Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA projectors (PDF, 379KB) - Page 55
...2 exists.)
CTLR DLA
'!' '1' SP 'W00' SP '0002' CR '@' ...DLA
'?' '1' SP 'W00' CR '@' '1' SP '0' SP '0000' CR
54 12.39 Switcher Selection : 'W00'(57H 30H 30H)
Definition
：
Command Parameter type
Reply time Conditions
Changes channels according to RGB. When Projector receive the command, Projector switches input terminal to commands from the Switcher. When it is not set...
JVC DLA-M2000SC Reviews
We have not received any reviews for JVC yet.