JET Tools GH-1440-1 Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools GH-1440-1 manuals!
Problems with JET Tools GH-1440-1?
Ask a Question
Free JET Tools GH-1440-1 manuals!
Problems with JET Tools GH-1440-1?
Ask a Question
Popular JET Tools GH-1440-1 Manual Pages
User Manual - Page 1
This .pdf document is bookmarked
Operating Instructions and Parts Manual
Geared Head Lathe 14x40 inch
Model GH-1440
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No. M-322830 Edition 1 06/2017
Copyright © 2017 JET
User Manual - Page 2
...do not use a tool at all warnings posted on the machine.
20.
Safety guards must be repaired or replaced.
10. Read and ... be supported by properly trained and experienced personnel only. Make the workshop child proof. Maintain tools with ... IMPORTANT SAFETY
INSTRUCTIONS
Read and understand the entire owner's manual before attempting set -up or operation of parts, mounting, and...
User Manual - Page 4
...
Section
Page
1.0 IMPORTANT SAFETY INSTRUCTIONS ...2 2.0 Table of contents...4 3.0 About this manual ...5 4.0 Specifications ...6 5.0 Uncrating ...8
5.1 Contents of shipping container ...8 6.0 Installation ...9
6.1 Chuck preparation (three jaw) ...9 7.0 Lubrication...10 8.0 Coolant preparation...12 9.0 Electrical connections ...12
9.1 Voltage conversion (GH-1440-3 only) ...12 10.0 General...
User Manual - Page 5
... transfers ownership, the manual should accompany it. Failure to be a training guide for information on installation, safety precautions, general operating procedures, and maintenance instructions. Exploded View 55 14.15.2 Thread Dial Assembly - Parts List 59 14.19.1 Lead Screw Cover Assembly - If there are used in accordance with the instructions as set forth in card provided...
User Manual - Page 6
...Specifications
Table 1
Model number Stock number Motor and Electricals Motor type Horsepower Phase Voltage Cycle Listed FLA (full load amps) Start capacitor Run capacitor Motor speed Power cord Power plug installed... Compound and carriage Tool post type Maximum tool size Maximum compound slide travel Maximum cross slide travel Maximum carriage travel
GH-1440-1 322830
GH-1440-3 322840
single 230V...
User Manual - Page 7
GH-1440-1
GH-1440-3
4-3/4 in. (121 mm) 1-3/4 in. (45 mm)
MT3
Cast iron Cast iron Cast iron Cast... lb (1060 kg)
1 subject to local and national electrical codes. 2 The specified values are emission levels and are not necessarily to change specifications at time of publication, but because of our policy of continuous improvement, JET reserves the right to be seen as safe operating levels. L...
User Manual - Page 8
...manual before attempting set-up or operation. Missing parts, if any, should be reported to your distributor.
Do not discard any damage immediately to your distributor and shipping agent.
5.0 Uncrating
Open shipping crate and check for Cam Locks 1 Tool Post Wrench 1 Taper Piece 1 Operating Instructions and Parts Manual...1 Tool Box (p/n GH1440-TBCP)
Tool Box Contents (p/n GH1440-TBCP...
User Manual - Page 9
... end gear assembly and coat all parts thoroughly with Mobilith® AW 1.... must be level to service the lathe on an adequate... lathe.
2. 6.0 Installation
1. Finish removing the wooden crate...tool box.
2. Do not use paint thinner, gasoline, or lacquer thinner, as these can damage painted surfaces. Failure to comply may cause serious injury and/or damage to reach a level condition. Support...
User Manual - Page 14
... sliding points with its fingers around the workpiece.
The sliding fingers are required as a support for tuning operations on front of the cutting tool. turns coolant pump on the free tailstock end. C.
Secure the steady rest in position.
3. Set the fingers snugly to stop all machine functions. Fingers should be moved with Mobil...
User Manual - Page 17
.... 19) out of this manual).
2. Setting the gears too tight will cover...found in the tool box are installed in the ...Set selector levers (A, B, C, D, Fig. 21) to be set at "F" or "D", depending on which gear is a backlash of the
headstock. 3. 11.2 Feed and thread selection
1. Move levers (B, C, D, E, F, Fig. 18) to the appropriate positions according to the chart.
11.3 Change gears replacement...
User Manual - Page 20
...wrench.
4. If the measurements are the same. Make another cut a piece approximately eight inches long.
3. Set gap bridge in their respective holes and seat using a mallet. Install six socket head cap screws and tighten securely.
20
Figure 25 Figure 26 Re-test alignment if any ... tailstock or center to back. If the lathe is level side to side and front to support the other .
User Manual - Page 22
... at local hardware stores, or may not be ordered from JET. 13.0 Operation tables
13.1 Thread table
13.2 Feed table
14.0 Replacement Parts
Replacement parts are shown for reference only, and may be available individually.
22 to serve you quickly and accurately. Having the Model Number and Serial Number of your machine available when you call...
User Manual - Page 46
... Label 1 43 GH1440K-03303 ....... Flange...1 9 GB4141. 14 Knob BM10x50 2 10 GH1440K-03705 ....... Lever Support 1 12 GH1440K-03703 ....... Eccentric Shaft 1 35 GH1440K-03709 ....... Clamping Block 1 39 F010446 Socket Set Screw DP M10×40 1
40 GH1440K-03714 ....... Parts List
Index No. Part No. Hub ...1 4 BB-8103 Thrust Bearing 8103 1 5 KF2R4420 Key, Dbl Rd Hd 4x20...
User Manual - Page 51
...1 26 GH1440K-22703 ....... Angle Steel M12 1 27 TS-2311061 Hex Nut M6 1 28 TS-1524021 Socket Set Screw M8x10 1 29 GH1440A-22705 ....... Brake Pedal 1 40 JET-165 JET Logo 165x68mm 1 41 C0632A-22704 .......... Bracket...2 48 GH1440K-01711 ....... Support ...1
51 Pedestal (right 1 50 GH1440K-18701 ....... 14.12.2 Stand and Brake Assembly - Cover ...1 6 TS-1550041...
User Manual - Page 67
...tools needs service or repair, please contact Technical Service by JPW Industries, Inc.
How to the limitations stated below ) • Accessories carry a limited warranty of one of maintenance.
For complete, up-to parts...PURPOSE ARE EXCLUDED.
The specifications listed in JET printed materials and on the JET website. Manual Hoists; 16.0 Warranty and service
JET® warrants every ...
JET Tools GH-1440-1 Reviews
We have not received any reviews for JET Tools yet.