JET Tools JAT-400 Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools JAT-400 manuals!
Problems with JET Tools JAT-400?
Ask a Question
Free JET Tools JAT-400 manuals!
Problems with JET Tools JAT-400?
Ask a Question
Popular JET Tools JAT-400 Manual Pages
User Manual - Page 2
... Air Tools; Manual Hoist Accessories;
Product Listing with your product or on This Warranty JET LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH PRODUCT. Shop Tools; Warranty Period The general warranty lasts for further clarification. This warranty does not cover failures due directly or indirectly to the JET brand.
2 JAT-400 Micro...
User Manual - Page 3
... your exposure to these chemicals are specifically designed to cause cancer, birth defects or...JET disclaims any real or implied warranty and holds itself harmless from heat and sharp edges. JET...tool without a work load on how often you do this entire manual before operating.
11. Repair or replace damaged air hose immediately. Safety warnings
General air tool warnings
1. Replace...
User Manual - Page 4
...risk of die grinder.
37. Maintain tools with the proper and safe operation of this manual:
fatal, injury. These can be ...When not in use power tools in minor injury and/or possible tool damage.
4 JAT-400 Micro Die Grinder Specific warnings for deburring, polishing, ...lubricate the tool with your finger off air supply and discharge any bottled gas as kerosene, diesel or jet fuel.
...
User Manual - Page 5
...supplier or JET. As with the instructions set forth in this manual for a JET Model JAT-400 Pneumatic Micro Die Grinder. Your tool has been designed and constructed to take appropriate precautions and exercise common sense. If there are questions or comments, please contact your tool on safety precautions, general operating procedures, maintenance procedures and parts breakdown. This...
User Manual - Page 6
Tool specifications
Model number Stock number Collet size Horsepower Free speed Average air consumption Air inlet Air hose inside diameter Required air pressure Vibration value Noise level 1 Speed setting Grip Hose included Overall Length Housing material Net weight Shipping weight
JAT-400 505400 1/8 in. 0.1 54,000 RPM 1.4 CFM 1/4 in . 90 psi (621 kPa) 0.6 m/s2 76 dB(A) variable...
User Manual - Page 7
... wrench.
5. Do not use a damaged tool. Do not use detergent oil.
3. Set air pressure to turn on and adjust speed.
8.
Blow out air line to remove any dirt or moisture, then connect air supply hose to distribute the oil. Read this instruction manual thoroughly for a few seconds to tool. Storage
Avoid storing the die grinder...
User Manual - Page 8
... nut with a replaceable air filter that can be easily cleaned. Set air pressure to serve the working area. Drain water from air compressor tank daily, as well as using multiple hoses, air hoses should be larger than 8 seconds to specifications, the following are not used for the job.
Tool Pressure
JET Air Tools operate on a regular...
User Manual - Page 10
.... Moisture or obstruction in this manual.
10 JAT-400 Micro Die Grinder Improper lubrication. clear any kinks or bends. If problem persists, disassemble, clean and lubricate internal parts. Disassemble and inspect bearing. set .)
Inspect and repair air regulator. Check and clean air filter on components.
Problem
Possible cause
Remedy
Tool will not start. Starts immediately...
User Manual - Page 11
... JAT400-03 O-Ring ø14x10 JAT400-04 Air regulator JAT400-05 O-Ring ø3x2.1 JAT400-06 Connector JAT400-07 Pin JAT400-08 Plug JAT400-09 Intake plate BB-693ZZ Ball bearing 693ZZ JAT400-11 Bearing plate JAT400-12 Pin JAT400-13 Cylinder JAT400-14 Rotor vane JAT400-15 Rotor
Qty Index Part No. parts breakdown
Index 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Part No. #505400, JAT-400...
User Manual - Page 12
Please have the stock number and serial number of your tool available when you quickly and accurately.
427 New Sanford Road LaVergne, Tennessee 37086
Phone: 800-274-6848 www.jettools.com to 5:00 p.m. CST. Replacement parts
To order parts or reach our service department, call , so that we may serve you call 1-800-274-6848 Monday through Friday, 8:00 a.m.
JET Tools JAT-400 Reviews
We have not received any reviews for JET Tools yet.