JET Tools 608003 Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools 608003 manuals!
Problems with JET Tools 608003?
Ask a Question
Free JET Tools 608003 manuals!
Problems with JET Tools 608003?
Ask a Question
Popular JET Tools 608003 Manual Pages
User Manual - Page 1
M-629004 Revision B5 07/2015 Copyright © 2015 JET This .pdf document is bookmarked
Operating Instructions and Parts Manual
Drum Sander
Model 16-32 Plus
shown with optional casters (98-0130) and infeed/outfeed tables (98-1601)
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No.
User Manual - Page 2
... of our tools needs service or repair, please contact Technical Service by a 90 day limited warranty against manufacturers' defects. Motors; Woodworking Machinery Limited Lifetime - Manual Hoists; Warranty Period The general warranty lasts for further clarification. Use of these machines in the literature included with a Five Year Warranty that you specific legal rights, subject to...
User Manual - Page 3
... and Service ...2 Warning...4 Introduction ...6 Specifications ...6 Features and Terminology ...7 Unpacking ...8
Contents of Boxes...8 Assembling the Stand...9
Casters (Optional Accessory)...9 Assembling the Sander...10
Installing Drum Head...10 Installing Conveyor...10 Infeed and Outfeed Tables (Optional Accessory 11 Dust Collection...12 Installing Abrasives ...12 Grounding Instructions ...14...
User Manual - Page 6
.... See note on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. As workplace conditions vary, this manual were current at time of publication, but because of our policy of the hazards and risks involved only. JET can also be seen as safe operating levels. Specifications
Stock Number...629004K Model Number...16-32 Plus...
User Manual - Page 8
.... Unpacking
Open boxes and check for assembly, maintenance and safety instructions. Any missing parts should be reported to comply may cause serious injury.
8
Figure 2 - (Box #1) Figure 3 - (Box #2) Compare the contents of this instruction manual thoroughly for shipping damage. Read this manual before attempting set-up or operation!
Failure to your distributor and shipping agent.
User Manual - Page 11
...the tables are still too high for proper support of stock. Lower the sanding drum to the two holes in contact with a 7/16" wrench. Install the other side of table.
4. Make.... See "Conveyor Belt Tension/Tracking" on the bracket. Install a bracket (A, Figure 8) to securely hold the straight-edge in Figure 8. See Figure 9. To set ." Securely re-tighten the flanged hex nuts. If the...
User Manual - Page 16
...achieved, turn at the fastest speed setting. Try to highest position. To replace a worn conveyor belt, raise ...drum to avoid overadjustments. Dust Cover Latch
The dust cover latch prevents the dust cover from control box receptacle.
2.
Adjust conveyor take -up screw nut on the opposite side. Note that the dust cover latch can cause tracking problems...
User Manual - Page 17
... the alignment with the drum alignment occurs, follow the instructions below. Insert the gauge between the drum and conveyor bed..., alignment is parallel to the conveyor bed for installation of the drum.
If a problem with a gauge of the machine.
4. If...the drum, counterclockwise to the same degree as a gauge.
1. Set conveyor on two screws -
The sanding drum comes preset from the ...
User Manual - Page 20
.... Hardness of sanding. Always maintain control of the piece being processed. 3.
If the drum motor is fed directly in contact with the feed rate set at this manual on the outfeed roller. If the finish is smooth and the machine is slipping, or if you can lower the drum slightly more revolutions...
User Manual - Page 21
...stock. Also, a hose smaller than the manual setting on the drum decreases, SandSmart will increase...of the stock which can slip on your specific conditions and make adjustments by slowing the ...problems occur, first check and adjust the feed rate, referring to use its capabilities range from experimenting with slower, dust-generating hand sanders.
Learning how to the "Troubleshooting...
User Manual - Page 22
If possible, support such stock as it is very important to the drums). If there is room, angling the stock on parts such as the drum goes from sanding the rails at a 90°...Frames and Raised Panel Doors
It is being sanded to take special care when sanding stock that is set screws for stock removal is in the stock can adversely affect performance through the machine so it will ...
User Manual - Page 24
....
Abrasive improperly wrapped.
Strip not cut and re-install the abrasive strip.
Inadequate dust collection. Use an open-coat abrasive.
Re-tension rollers (see page 19). Abrasive is loose or unattached.
Use coarser grit or reduce depth of cut .
Improper conveyor belt tension.
Troubleshooting
Trouble
Probable Cause
Remedy
No incoming power.
Check plug...
User Manual - Page 25
... loose bolts, loose shaft coupling set screws, or out-of cut and/or feed rate.
Conveyor bed flexing or vibration. Work piece not properly supported. Reduce feed rate.
Add work pieces.
Trouble
Board slips on conveyor. Probable Cause Tension rollers too high. Stock slipping on conveyor belt.
Replace conveyor belt. See pages 18-19...
User Manual - Page 27
...9060 60-9080 60-9100 60-9120 60-9150 60-9180 60-9220
Locking Casters, set of 4
Infeed/Outfeed Tables Ready-To-WrapTM Abrasive Strip, 36 Grit, (4 wraps in...parts or reach our service department, call will allow us to serve you quickly and accurately.
27 Having the Model Number and Serial Number of the above abrasive strips are listed on the following pages. Replacement Parts
Replacement parts...
User Manual - Page 29
... Take-Up Slide Bracket 2 28 20-1161 Wave Washer 1/4 4 29 TS-0680021 Flat Washer 1/4 4 30 40-0005 Drive Roller Support Bracket 1 31 10-9106 Hex Washer Head Bolt 5/16"-18x3/4 4 32 60-0316-P Conveyor Belt (not shown 100 grit 1 ... 5/32x1/2 2 41 72-2250-03 Flat Washer 5/16 1 42 72-2250-05 Slotted Set Screw 8-36UNFx5/16 1
29 Parts List: Conveyor and Motor Assembly
Index No...
JET Tools 608003 Reviews
We have not received any reviews for JET Tools yet.