InSinkErator Model Hot1 Support and Manuals
Get Help and Manuals for this InSinkErator item
View All Support Options Below
Free InSinkErator Model Hot1 manuals!
Problems with InSinkErator Model Hot1?
Ask a Question
Free InSinkErator Model Hot1 manuals!
Problems with InSinkErator Model Hot1?
Ask a Question
Popular InSinkErator Model Hot1 Manual Pages
Specifications - Page 1
...of Emerson Electric Co.
Specifications
Capacity
1/3-gallon copper tank dispenses 40 cups of 190°F water per hour
• 1-Year We Come To You® In-Home Service Warranty*
• 115 volts, 500 watts, 4.3 amps • Available in polished stainless steel
with black handle
Sample Specification
Instant hot water dispenser(s) shall be InSinkErator Model Hotl with adjustable temperature...
Owners Manual - Page 1
Model Hot1
Instant Hot Water Dispenser
Owner's Manual
Installation, Care & Use
Instalacion, cuidado & uso Installation, soin et utilisation
Owners Manual - Page 2
...not be controlled by the same wall switch that all instructions, cautions, warnings and dangers before installing or using this instant hot water dispenser. WHAT YOU NEED TO GET STARTED
Equipment Required:
I... to local codes.
I This outlet must have a SinkTop Switch™ from InSinkErator®. I This unit does not contain a drain plug and should not be installed where periodic ...
Owners Manual - Page 3
... moderate injury. What you'll see in order for the appliance to support the narrative. 3 CAUTIONS, WARNINGS and DANGERS that operates your disposer.
The manual is setup this way to allow you progress through the installation.
2 Contains simple illustrations that provide visual instruction to operate properly.
Hold valve open at any point after completing a section...
Owners Manual - Page 4
Maximum Countertop Thickness for Mounting
2"
(5.1cm)
DIMENSIONS
Spout
4"
(10.2cm)
2½"
(6.4cm)
Spout Holder
6"
(15.2cm)
Mounting Nut
Rubber Gasket
3"
(7.6cm)
Valve Lever
Slotted Set Screw (Opposite Side) Wing Nut
11¾8"
(28.9cm)
Width of Unit 5¼"
(13.3cm)
3 Wire Power Cord 30" Long
(76cm)
2¼9 16 "
(6.5cm)
¼" Copper Tube 16" Long
(40.6cm)
Cold Water Line
4
Owners Manual - Page 5
...5
I Plug hose opening with an instant hot water dispenser. I If drilling a hole into a surface other than stainless steel.
I Turn off water supply.
START HERE
1 PREPARATION
A
Required minimum...replace the soap dispenser in sprayer hole. It should not be fused.
The wall outlet for the dispenser. I If using the sink sprayer hose hole, remove nut that operates your dispenser...
Owners Manual - Page 6
... holder
approximately 2 full turns and
pull out spout. 2
INSTALLING THE DISPENSER
A
I Remove the spout by
tightening the wing nut from hot water spray.
D Spout
Rubber Seal
Personal Injury: Failure to tighten set screw.
6 I Align spout so water runs into dispenser as far as it will go and tighten set screw allows easy removal of unit with spout removed...
Owners Manual - Page 7
....6 cm) long, 1/4" diameter copper tube on the dispenser to clogging. This will flush the line of water run through it into a pan. 3
WATER CONNECTION OPTIONS
T-fitting 1/4" Diameter Tube
Cold Water Supply Line
Compression valve or T-fitting option (not supplied):
I Ensure that a shutoff valve is a more complex installation and should only be attempted by an experienced...
Owners Manual - Page 8
... the 1/4" copper
line from the dispenser so it will go. Bend tube carefully. Don't use paste-type sealants on
water line connections. Tighten compression fittings snug but don't over the ferrule with
your fingers.
Then tighten the nut firmly with
the other hand. With one hand,
support the copper line coming from the...
Owners Manual - Page 9
...fuse is still emitted after setup, thermostat adjustments may damage heating element or thermal safety fuse and will be needed (pg. 11).
9
Steam and/or hot water coming from the spout....see if your Authorized Service Center. Property Damage: Do not connect electric power until water freely runs out of water from the spout without pressing down for water to reach target temperature...
Owners Manual - Page 10
... these instructions or local electrical and/or plumbing codes. Use only parts provided. DO NOT store or use gasoline or other flammable vapors and liquids in your home. To avoid possible property damage, this instant hot water dispenser should be for repairs or replacement components. If warranty service is required during the warranty period, contact an authorized InSinkErator service agent...
Owners Manual - Page 11
... unit. I To avoid water damage from leakage, replace all cut, loose or split...setting. I Disconnect power from service.
May result in place for the water to re-heat to decrease temperature. If there are signs of water damage, immediately remove the unit from unit.
SEASONAL STORAGE/DRAINAGE
Anytime the instant hot water dispenser is cool. I After adjusting, depress the dispenser...
Owners Manual - Page 12
...• The expansion chamber isn't draining • Unplug the unit.
Water is boiling. Please read Troubleshooting Guide and/or visit www.insinkerator.com before calling AnswerLine™
TROUBLESHOOTING
PROBLEM
Water and steam spits forcefully from spout without turning on tank front. Water is too hot or not hot enough
• Thermostat is dripping from the spout/vent constantly
•...
InSinkErator Model Hot1 Reviews
We have not received any reviews for InSinkErator yet.