Instruction Manual
Page 1
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. INSTRUCTION MANUAL VHF TRANSCEIVER iV80 iV80E This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. INSTRUCTION MANUAL VHF TRANSCEIVER iV80 iV80E This device complies with Part 15 of the FCC Rules.
Instruction Manual
Page 2
... and craftsmanship. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. The IC-V80/ V80E vhf transceiver is designed and build with Icom's philosophy of personal injury, fire or electric shock. EXPLICIT DEFINITIONS WORD R DANGER! SAVE THIS INSTRUCTION MANUAL- Personal injury, fire hazard or electric shock may occur. With proper care, this...
... and craftsmanship. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. The IC-V80/ V80E vhf transceiver is designed and build with Icom's philosophy of personal injury, fire or electric shock. EXPLICIT DEFINITIONS WORD R DANGER! SAVE THIS INSTRUCTION MANUAL- Personal injury, fire hazard or electric shock may occur. With proper care, this...
Instruction Manual
Page 16
...any other equipment, or for any of battery performance. R DANGER! R DANGER! Use the battery only with Icom chargers. If fluid from inside the battery gets in this instruction manual. R DANGER! Immediately stop using . R DANGER! DO NOT hammer or otherwise impact the battery. Using third...occur, contact your eyes with fluid from inside the battery. NEVER solder the battery terminals, or NEVER modify the battery pack. Rinse your Icom dealer or distributor. R WARNING! If any purpose that comes into contact with clean water, without rubbing them, and see a doctor ...
...any other equipment, or for any of battery performance. R DANGER! R DANGER! Use the battery only with Icom chargers. If fluid from inside the battery gets in this instruction manual. R DANGER! Immediately stop using . R DANGER! DO NOT hammer or otherwise impact the battery. Using third...occur, contact your eyes with fluid from inside the battery. NEVER solder the battery terminals, or NEVER modify the battery pack. Rinse your Icom dealer or distributor. R WARNING! If any purpose that comes into contact with clean water, without rubbing them, and see a doctor ...
Instruction Manual
Page 21
... adjust the squelch level. 3 • "SqL 1" is loose squelch (for weak signals) and "SqL10" is tight squelch (for 1 sec. "SqL 0" is open 14 the squelch manually. You can use it without disturbing the 15 squelch setting, even when mute functions such as the tone squelch are in use. 16 ➥ Push...
... adjust the squelch level. 3 • "SqL 1" is loose squelch (for weak signals) and "SqL10" is tight squelch (for 1 sec. "SqL 0" is open 14 the squelch manually. You can use it without disturbing the 15 squelch setting, even when mute functions such as the tone squelch are in use. 16 ➥ Push...
Instruction Manual
Page 24
... before transmitting. w Adjust the volume level. e P ush and hold [MONI] to set the desired volume level. (p. 14) • The volume level is open the squelch manually. to monitor) q Turn the power ON. "SqL 0" is displayed on the LCD while setting. • "SqL 1" is loose squelch (for weak signals) and "SqL10" is...
... before transmitting. w Adjust the volume level. e P ush and hold [MONI] to set the desired volume level. (p. 14) • The volume level is open the squelch manually. to monitor) q Turn the power ON. "SqL 0" is displayed on the LCD while setting. • "SqL 1" is loose squelch (for weak signals) and "SqL10" is...
Instruction Manual
Page 28
...) or "+" (positive offset). • "-" or "+" indicates the transmit frequency is shifter up ) - (down) 21 For the U.S.A. version: The auto repeater function has priority over the manual duplex setting. q Push [FUNC](M), and then [SET](8) to exit the Set mode. Input freq. : 145.300 MHz Direction : - (down (-) from the receive frequency. • Blinking...
...) or "+" (positive offset). • "-" or "+" indicates the transmit frequency is shifter up ) - (down) 21 For the U.S.A. version: The auto repeater function has priority over the manual duplex setting. q Push [FUNC](M), and then [SET](8) to exit the Set mode. Input freq. : 145.300 MHz Direction : - (down (-) from the receive frequency. • Blinking...
Instruction Manual
Page 41
.../code does not match, the squelch does not open. No indication : Cannot be used ac- 14 cording to access the repeater or open the squelch manually, push and hold [MONI]. t P ush [PTT] to answer. ■ Tone scan 1 By monitoring a signal from a repeater, pocket beep or 2 squelch function operation, you can determine...
.../code does not match, the squelch does not open. No indication : Cannot be used ac- 14 cording to access the repeater or open the squelch manually, push and hold [MONI]. t P ush [PTT] to answer. ■ Tone scan 1 By monitoring a signal from a repeater, pocket beep or 2 squelch function operation, you can determine...
Instruction Manual
Page 43
... the DTMF TX key to "dmt.k" in the Set mode. ➥ W hile pushing and holding [PTT], push the desired keys to transmit a DTMF code sequence manually. • Push [0]-[9] for "0"-"9," [MONI] for "A," [] for "B," [] for "C," D Using a DTMF memory channel 2 First, set the DTMF TX key to "dmt.t" in the Set mode...
... the DTMF TX key to "dmt.k" in the Set mode. ➥ W hile pushing and holding [PTT], push the desired keys to transmit a DTMF code sequence manually. • Push [0]-[9] for "0"-"9," [MONI] for "A," [] for "B," [] for "C," D Using a DTMF memory channel 2 First, set the DTMF TX key to "dmt.t" in the Set mode...