Icom IC-M400BB Support Question
Icom IC-M400BB Support Question
Find answers below for this question about Icom IC-M400BB.Need a Icom IC-M400BB manual? We have 1 online manual for this item!
Question posted by Stef2 on September 1st, 2015
Do You Have A Dutch Manual For The Icon 400bb?
The person who posted this question about this Icom product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by TommyKervz on September 1st, 2015 8:32 AM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,813
Member since:
January 10th, 2013 Points: 17,776,813
Related Icom IC-M400BB Manual Pages
Instruction Manual - Page 1
Operation is subject to the condition that this device does not cause harmful interference. COMMANDMICIV™ (HM-195) may not be supplied, depending on the transceiver version.
INSTRUCTION MANUAL
VHF MARINE TRANSCEIVER
iM400BB
This device complies with Part 15 of the FCC Rules.
Instruction Manual - Page 2
...des ign of your radio of choice, and hope you with years of the art technology and craftsmanship. SAVE THIS INSTRUCTION MANUAL -
If disregarded, inconvenience only....using the transceiver. DDFEATURES ❍ Built-in -
We appreciate you making the IC-M400BB your IC-M400BB. EXPLICIT DEFINITIONS
WORD RWARNING! i
IMPORTANT
READ ALL INSTRUCTIONS carefully and completely
before ...
Instruction Manual - Page 4
... in order to the height of the antenna, unless such persons (such as driver or radio operator) are shielded from the lowest point of the antenna), to the heads of all ... minimum safe separation distance estimated to meet the FCC and IC Requirements for all possible personnel. THIS ESTIMATE IS MADE ASSUMING THE MAXIMUM POWER OF THE RADIO AND ANTENNAS WITH A MAXIMUM GAIN OF 9dBi ARE USED ...
Instruction Manual - Page 6
...to comply with the limits for a Class A digital device, pursuant to part 15 of the radio as to be readily seen from the operating controls of the FCC Rules.
COUNTRY CODE LIST
&#...FCC regulations, this equipment in a residential area is operated in accordance with the instruction manual, may cause harmful interference to cause harmful interference in the diagram below. These limits are...
Instruction Manual - Page 8
...;■ Options 12
6 CHANNEL LIST 13-14
7 TROUBLE SHOOTING 15 TABLE OF CONTENTS
FOREWORD i IMPORTANT i EXPLICIT DEFINITIONS i IN CASE OF EMERGENCY ii INSTALLATION NOTE ii RADIO OPERATOR WARNING iii AVERTISSEMENT POUR LES OPÉRATEURS...
Instruction Manual - Page 9
... entries.
8
A current copy of opera- It is your craft's identification for vessels in any way.
• Indecent or profane language is compulsory. If required, only a licensed radio operator may operate a transceiver.
5
6
However, non-licensed individuals may require a current radio station license before using the transceiver. However, even if you , cannot lawfully be . DDPrivacy...
Instruction Manual - Page 11
... [ENT] to enter all 10 digits. selected, and then push [ENT] or Dial to the normal operating mode.
PREPARATION 2
■■ATIS code programming (For Dutch version transceivers)
1
The 10 digit ATIS (Automatic Transmitter Identification System) code can be changed by using Dial, or Push [ENT] or Dial to set it...
Instruction Manual - Page 12
... B AIS TRANSPONDER is specified by the coast station, therefore you correctly set to the next step whenever the detail screen of the HM-195 instruction manual. 3 AIS TRANSPONDER
■■Making an Individual call using the transponder.
ger list display. • Y ou can be specified by the Base station," in step...
Instruction Manual - Page 15
... the OPC-2014* cable. Use a 2
PH M3 × 6 screw (not supplied).
3
y COMMAND MICROPHONE JACK
4
Connects to the HM-195.
5
NOTE: For those who purchased the IC-M400BB and HM-195
separately.
6
When connecting the HM-195 for the first time,
7
a firmware update (if needed) will take a maximum of 2 minutes.
11
DO NOT...
Instruction Manual - Page 23
...
POSSIBLE CAUSE
SOLUTION
REF.
1
The transceiver does • Bad connection to the power supply.
• Check the connection to the HM-195 commandmiciv™ instruction manual.
13
14
15
16
15
Similar Questions
A220 Radio- New Out Of Box - Station Reported That Frequencies Were Manually Pro
when powered on display stuck in ICOM (NO Frequencies displayed)
when powered on display stuck in ICOM (NO Frequencies displayed)
(Posted by BarneyPhillips 11 months ago)
I Need The Programming Instructions For The Icom Ic-v80 For The Non Us Version
I wish to change the frequency of my Icom VC-V80 but the VFO/MR/CALL button for selecting frequency ...
I wish to change the frequency of my Icom VC-V80 but the VFO/MR/CALL button for selecting frequency ...
(Posted by Eziukwukamalu 8 years ago)
Intercom Manual Ppt
Is it possible to setup the icom-A210 so that the automated VOX intercom is manually operated throug...
Is it possible to setup the icom-A210 so that the automated VOX intercom is manually operated throug...
(Posted by damccall 9 years ago)
How Do You Manually Program An Icon Fc4011
Can you manually program an icom fc4011 to be uused with other fc4011s? We received new radios, but ...
Can you manually program an icom fc4011 to be uused with other fc4011s? We received new radios, but ...
(Posted by tburns35546 9 years ago)