Hard Drive Specifications
Page 39
...) GROUND LED Cathod 12 10 8 6 4 2 (Reserved) (Reserved) (Reserved) | Note: Pin #9 is to Option Jumper Block. The setting at Option Jumper Block and the Auxiliary Connector work as -DAS0,1,2,3. Pin #1,3,5,7 specify SCSI-ID as logical OR. Auxiliary Connector Specification 29 The drive conforms SFF-8009 Rev3.0. Pin #8 is for external LED cathod. | If pin #9 is...
...) GROUND LED Cathod 12 10 8 6 4 2 (Reserved) (Reserved) (Reserved) | Note: Pin #9 is to Option Jumper Block. The setting at Option Jumper Block and the Auxiliary Connector work as -DAS0,1,2,3. Pin #1,3,5,7 specify SCSI-ID as logical OR. Auxiliary Connector Specification 29 The drive conforms SFF-8009 Rev3.0. Pin #8 is for external LED cathod. | If pin #9 is...
Hard Drive Specifications
Page 40
...option control, Unit Attention option control, SCSI terminator ON/OFF setting, Auto start delay option control and SCSI parity option control. Some of DDRS-3xxxx DC power Connector Auxiliary Connector SCSI 68 pin Connector Logic card Position# 1 < Option Jumper Block Position# 12 Position#: 12 11 10 Pin#: 1..."Auxiliary Connector on 68-pin Model" on page 29. 6.2 Option Jumper Block The 12 positions jumper block shown below is not compatible with previous IBM HDDs such as logical O R between Option Jumper Block and Auxiliary Connector. It also provides an external Light Emitting Diode...
...option control, Unit Attention option control, SCSI terminator ON/OFF setting, Auto start delay option control and SCSI parity option control. Some of DDRS-3xxxx DC power Connector Auxiliary Connector SCSI 68 pin Connector Logic card Position# 1 < Option Jumper Block Position# 12 Position#: 12 11 10 Pin#: 1..."Auxiliary Connector on 68-pin Model" on page 29. 6.2 Option Jumper Block The 12 positions jumper block shown below is not compatible with previous IBM HDDs such as logical O R between Option Jumper Block and Auxiliary Connector. It also provides an external Light Emitting Diode...
Hard Drive Specifications
Page 45
... installed on 80 pin model. | Figure 27. No shunt jumper is installed on 80 pin model. | Figure 26. Default Jumper Setting of SE 50/68 pin model. 6.2.2 Shipping Default | No jumper is set as shipping default on 80-pin models. | SCSI ID is set to #6 as shipping default on 50/68-pin models. | SCSI terminator is...
... installed on 80 pin model. | Figure 27. No shunt jumper is installed on 80 pin model. | Figure 26. Default Jumper Setting of SE 50/68 pin model. 6.2.2 Shipping Default | No jumper is set as shipping default on 80-pin models. | SCSI ID is set to #6 as shipping default on 50/68-pin models. | SCSI terminator is...
Hard Drive Specifications
Page 103
... (Unit Attention Inhibit) bit is not used or checked by the user with older drives. MRG (Merge G-List into the Primary Defect List (P-List) during normal operation while the UAI jumper is for merging the Grown Defect List (G-List) entries into P-List) bit is allowed. QPE (Qualify Post ... inhibit the reporting of one causes the Target to zero but may however be set as 'Ignore' are recovered under Data Recovery Procedure (DRP) step. If the UAI jumper is added to report all recovered data errors. A QPE bit of recovered data errors which exceed the QPE threshold. Page ...
... (Unit Attention Inhibit) bit is not used or checked by the user with older drives. MRG (Merge G-List into the Primary Defect List (P-List) during normal operation while the UAI jumper is for merging the Grown Defect List (G-List) entries into P-List) bit is allowed. QPE (Qualify Post ... inhibit the reporting of one causes the Target to zero but may however be set as 'Ignore' are recovered under Data Recovery Procedure (DRP) step. If the UAI jumper is added to report all recovered data errors. A QPE bit of recovered data errors which exceed the QPE threshold. Page ...