IBM DPSS-309170 Support Question
IBM DPSS-309170 Support Question
Find answers below for this question about IBM DPSS-309170 - Ultrastar 9.1 GB Hard Drive.Need a IBM DPSS-309170 manual? We have 1 online manual for this item!
Question posted by pstamand on April 15th, 2010
Do You Have Jumper Settings For The Hd
need to install additional HD and need jumper settings , if any
Current Answers
Related IBM DPSS-309170 Manual Pages
Installation Manual - Page 1
IBM storage products
Installation and reference manual
IBM Ultrastar 36LP & 36LZX
3.5 inch Ultra 160 SCSI hard disk drive
Models: DPSS-336950 DDYS-T36950 DPSS-318350 DDYS-T18350 DPSS-309170 DDYS-T09170
IBM
IBM Technology Group Support Center
Page 1
07N5612IG10
Installation Manual - Page 2
...manual to your IBM Ultrastar. IBM storage products
Technical support
A Troubleshooting section is provided in the Appendix of this manual, call one of your installation question is at the...DRIVE E-mail drive@us.ibm.com
Singapore Voice 1800.418.9595 or 65.6.418.9595 E-mail drive@sg.ibm.com
United Kingdom Voice 44.1475.898.125 E-mail drive@uk.ibm.com
Germany Voice 49.7032.153050 E-mail drive...
Installation Manual - Page 3
....
©Copyright International Business Machines Corporation 2000. IBM storage products
Installation and reference manual
IBM Ultrastar 36LP & 36LZX
3.5 Ultra 160 SCSI hard disk drive
International Business Machines Corporation provides this publication "AS IS" without notice. these changes will be referred to restrictions set forth in certain transactions. Product data and specifications are...
Installation Manual - Page 4
... started Page 6 Handling precautions Page 6 Tools for installation Page 6
Begin the hardware install Page 6
Configure the jumper settings Page 7 Option jumper blocks Page 7 Assign a SCSI address Page 8 Enable optional features Page 8 The auxiliary connector on 68 pin models Page 10
Mount the drive Page 11
Attach the cables Page 12 Drives with 68 pin connectors Page 12...
Installation Manual - Page 5
... at the single-ended rate. However, some LVD controllers do not support single-ended SCSI drives. This manual provides installation instructions for the following model numbers:
Model DPSS-336950 DPSS-336950 DPSS-318350 DPSS-318350 DPSS-309170 DPSS-309170
Capacity 36.9 GB 36.9 GB 18.3 GB 18.3 GB
9.1 GB 9.1 GB
Connector Type 68 pin 80 pin SCA 68 pin 80 pin SCA 68 pin 80 pin...
Installation Manual - Page 6
..., remove it should be needed
again. Ÿ Remove the drive from your
system manufacturer, or by poor handling, physical impact, or electrostatic discharge (ESD). Do not touch the exposed printed circuit board or any
electronic components. Ÿ Do not press on the drive currently in your system to install the IBM Ultrastar drive. Ÿ A small flat...
Installation Manual - Page 7
... Group Support Center
Page 7
07N5612IG10 IBM storage products
Ÿ Record the following information for future reference: Drive model
Drive part number
Drive serial number
Date of purchase
Place of Purchase
Configure the jumper settings Option jumper blocks The drive has features that connects a pair of pins on a jumper block, thereby enabling a particular function in the...
Installation Manual - Page 8
... & 12, 13 & 14 7 & 8, 11 & 12, 13 & 14 9 & 10, 11 & 12, 13 & 14 7 & 8, 9 & 10, 11 & 12, 13 & 14
Enable optional features Termination Power (68 pin drives only) Place a jumper on pins ...
SCSI Address
0 1 2 3 4 5 6 7
Jumpers required on pins 3 and 4 of option block J4 if your host adapter or other device does not supply termination power.
Installation Manual - Page 9
...
off
off
off
off
on
off
on
off
off
on
off ' means that a jumper is delayed by a period of time multiplied by the drive's SCSI address. Disable Unit Attention Place a jumper on pins 11 and 12 of the drive is not installed.
Any pending Unit Attention conditions will be cleared at POR or SCSI Reset...
Installation Manual - Page 10
...the 150 Ohm resistor as indicated. This feature does not require the use of a jumper.
68pin
+5V
150 Ohms
Positions #1,#2 on J-4 Jumper Block (pin 1 of J-4) to LED Anode
(pin2 of J-4) to LED Cathode
...auxiliary connector. This connector conforms to pin 2 of option block J4. IBM storage products
Driving an LED To drive a Light Emtting Diode (LED) tie the LED Anode to pin 1 of option block ...
Installation Manual - Page 11
... allowable penetration of noted screw to system.
IBM storage products
Mount the drive Note: Drive bays and other enclosures vary in size and orientation from system to be... 4.0 mm. Thickness of its six surfaces facing down , or sideways. Max allowable penetration of noted screw to be 4.5 mm. The IBM Ultrastar...
Installation Manual - Page 13
... # : # 0:0 - IBM storage products
Verify host adapter settings
Note: The example below uses the Adaptec 2940UW controller with DPSS-318350.
1. Turn the computer on. You should see the drive model displayed when the system is booting. 3.
Drive C: (80h)
CPU/CLK Math Coprocessor Fixed Disk 0 Fixed Disk 1 Fixed Disk 2
: Pentium/133MHz : Installed : None : None : None
Base Memory...
Installation Manual - Page 14
... Host Adapter SCSI ID 7 SCSI Parity Checking Enabled Host Adapter SCSI Termination Automatic
Additional Options Boot Device Options Press SCSI Device Configuration Press Advanced Configuration Options Press
7.... Lun Number...0
8. The following screen is displayed. Verify that configuration settings
are enabled (set the Boot Target ID. 9. Adaptec AHA-2940 Ultra/Ultra W SCSISelect...
Installation Manual - Page 15
... the previous screen. 16.
IBM storage products
13. Verify that Extended BIOS Translation for DOS Drives > 1 Byte and BIOS Support for Ultra SCSI Speed...Enabled
14. Adaptec AHA-2940 Ultra/Ultra ... Removable Disks Under BIOS as Fixed Disks Boot Only Extended BIOS Translation for DOS Drives > 1 GByte Enabled Display Message During BIOS Initialization...Disabled BIOS Support for Bootable CD...
Installation Manual - Page 16
... will appear which allows you enable large disk support and create any new drives on large drives, and allowing disks over 2 GB to be displayed. In addition, disk utilities that were not designed explicitly for large disks, resulting in size. If you need to access this disk, you will not be partitioned.)
Note: Select FAT...
Installation Manual - Page 18
...
Page 18
07N5612IG10
Note the drive letters to the hard drive. The /s option makes your operating system installation instructions. If you encounter this drive to format the drive depends upon the size of the drive. 5. When the formatting is complete, format the next logical drive by following warning is the drive letter).
The time needed to be recognized. Repeat the...
Installation Manual - Page 19
.... If you will need to the installation manual enclosed with your computer. If a chip set is embedded into your...hard drive. Replace the screw and connect the SCSI cables to create a DOS startup diskette: 1. From Windows 95 or 98, double click My Computer. 3. IBM Technology Group Support Center
Page 19
07N5612IG10 Select Startup Disk tab. 6. Insert a blank floppy disk into drive...
Installation Manual - Page 23
.... For a definition of the specifications, see the SCSI Trade Association page at the end of the bus and set the jumpers for the drive for the interface transfer rate used and the number of devices installed on the bus. When attaching LVD devices to single-ended, wide or narrow adapters, the following Internet address...
Installation Manual - Page 24
...) on a hard drive. BIOS (Basic Input/Output System) The BIOS is only necessary with the interface requirements of sectors in a hard drive that it can be stored on a hard drive. Disk drive The primary data...on how the adapter handles the "Diff Sense" line on the interface, you may need to set the jumper on the drive to Force Single Ended mode.
ü On multi-channel SCSI adapters, do not ...
Installation Manual - Page 25
... that connects a pair of pins on a SCSI bus must be attached to a particular operating system or application and accessed as Ultra2 SCSI.
Jumper settings Different modes which are changeable by placing a jumper on a particular pair of a hard drive dedicated to a port on the system unit.
Partition A portion of pins on a device. Termination The signals on...
Similar Questions
Hard Disk Not Open
MY HARD DISK IS /IBM/IC25N020ATDA04-travelstar-20-gb-hard-drive MODEL.I PLUG IN EXTERNAL IDE CASE.BU...
MY HARD DISK IS /IBM/IC25N020ATDA04-travelstar-20-gb-hard-drive MODEL.I PLUG IN EXTERNAL IDE CASE.BU...
(Posted by gopikrish13 11 years ago)
I Need Install My Hd Like Slave In My Pc, No Knows Set Jump, Please Teach Me.
my PC is not IBM
my PC is not IBM
(Posted by elaragnafuccia 12 years ago)
How To Missing Hard Disk Drivers?
my hard disk drivers missing after installing windows 7 operating system
my hard disk drivers missing after installing windows 7 operating system
(Posted by wwwmalindasamaranayake 13 years ago)
What Are The Jumper Settings For This Hdd
(Posted by andyupton89 13 years ago)
How To Set Jumper To Master Mode
I am attempting to figure out how to set the jumper settings to master mode for an IBM Hard drive IC...
I am attempting to figure out how to set the jumper settings to master mode for an IBM Hard drive IC...
(Posted by wjgay 13 years ago)