Hunter 82042 Support and Manuals
Get Help and Manuals for this Hunter item
View All Support Options Below
Free Hunter 82042 manuals!
Problems with Hunter 82042?
Ask a Question
Free Hunter 82042 manuals!
Problems with Hunter 82042?
Ask a Question
Popular Hunter 82042 Manual Pages
Owner's Manual - Page 1
Installation
Guide
ENGLISH
See page 2
Español
Vea la página 19
Energy Star Bath Fan Light Models 82040, 82041, 82042
READ and SAVE THESE INSTRUCTIONS
1
42936-01 10/17/2007
Owner's Manual - Page 2
.... Follow the heating equipment manufacturer's guideline and safety standards, such as described in this manual. SAVE THESE INSTRUCTIONS.
2) Before installing, servicing, or cleaning the unit, disconnect the power by turning off position, securely attach a prominent ... electric shock, or injury to scale
Bath Fan
3 ft. min. (0.91 m) Tub or Shower area
42936-01 10/17/2007
Figure A
2
7 ...
Owner's Manual - Page 3
..., etc. off power unit.
13) Read specification label on product for installation in a tub or shower enclosure.
7) Installation work and electrical wiring must always be reached ...fan with all applicable codes and standards, including fire-rated construction codes and standards.
8) When cutting or drilling into wall(s) or ceiling, do not block air intakes or exhaust in a wall. Do not install...
Owner's Manual - Page 4
...Installation
A
Tools Needed. (Not supplied.) Estimated assembly time: 30 to 60 minutes
B
Turn off the power source.
42936-01 10/17/2007
Loosen the fan mounting screws.
4 If damaged, call 1-888-830-1326 for replacement...
Wiring Cover Wiring Cover Screw Strain Relief Bracket Strain Relief Bracket Screw Fan Assembly
Fan Mounting Screws Light Fixture
Lens
Included.
x6 A
*B *C
3/8" Cable...
Owner's Manual - Page 5
C
D
Remove the fan assembly from below, go to step D1, page 12.
5
42936-01 10/17/2007 For Existing Construction - accessible only from the housing. E
Loosen the wiring cover screw. attaching to joist, go to step C1, page 9. accessible from above, go to step B1, page 7.
Choose Installation Option For New Construction - For...
Owner's Manual - Page 6
... mounting screws (supplied) into the wiring access hole you made earlier. New Construction -
Tighten the strain relief around the wire.
42936-01 10/17/2007
6
Install the wiring and the strain relief into joist or framing.
A4
A5
3"
Run the power supply wire through the strain relief, leaving 3" between the end...
Owner's Manual - Page 9
...;⁄�"
OR
Remove an existing fan and check to make sure the opening needs to be 11" x 9 5/8".
9
42936-01 10/17/2007
Section C - The opening is large enough to the outside.
Existing Construction -
Use duct tape to Section E Final Installation on page 14. B10
B11
Install the wiring and the strain relief...
Owner's Manual - Page 11
C9
C10
3"
Tighten screws.
C12
Install the wiring and the strain relief into the wiring access hole you made earlier. Tighten the strain relief around the wire. C11
Run the power ...
Owner's Manual - Page 12
Go to Section E Final Installation on the top of the wire and the strain relief. Existing Construction - accessible from below
D1
D2
Remove one of the wiring access slugs on page 14. Remove the mounting rail brackets.
D3 EXISTING FAN
D4
3"
Remove an existing fan and check to make sure the opening is no...
Owner's Manual - Page 13
... joints. Use duct tape to the outside. D9
5/8
5/8
1/2
1/2
Position the bottom edge of the housing flush with the sheetrock. Go to be purchased.
D5
D6
Install the wiring and the strain relief into the ceiling. If ducting does not fit securely, an adapter
may need to Section E Final...
Owner's Manual - Page 14
...
EASIER IF TWO PEOPLE ARE INVOLVED.
DO NOT ALLOW THE FAN TO HANG FROM THE WIRING HARNESS.
Install the wiring cover box. E3
E4
Connect fan wiring harness. Install the fan assembly by inserting the tabs as shown.
Section E - Final Installation
E1
Fan Motor Night Light
Light
2 Pin
Black White
3 Pin
White Red Night Light Black Light...
Owner's Manual - Page 15
E9
Plug in wiring harness.
DO NOT ALLOW THE LIGHT FIXTURE TO HANG FROM THE WIRING HARNESS. E5
E6
Secure the fan assembly by tightening the two fan mounting screws. Remove light bulb cover. E10
Install the strain relief bracket.
INSTALLATION IS EASIER IF TWO PEOPLE ARE INVOLVED.
15
Position lighting fixture over mounting posts.
42936-01 10/17/2007 E7
E8
Remove thumbnuts.
Owner's Manual - Page 16
Install light bulb cover.
E9
Complete. E13
E14
Install night light. Restore power at the source.
42936-01 10/17/2007
16 E11
E12
Secure the fan assembly by tightening the two fan mounting thumbnuts.
Owner's Manual - Page 17
.... Solution: • Check and tighten all plug connections to be sure they are making excessive or unusual noises, contact Hunter Technical Support (see Troubleshooting section) to the appliance. Preventative Maintenance
A clean fan provides better service. Use water, a mild detergent such as described above ). Problem: Fan is secure. • Check the flapper to make sure it .
Owner's Manual - Page 18
... in the U.S.A. If your Bath Fan or provide a replacement free of sale to you due to repair the defect will be provided free of purchase is not purchased and installed in Memphis, Tennessee.
To obtain servicing, contact Hunter Fan Company Technical Support at http://www. After this Hunter Bath Fan:
If any part of your Hunter Bath Fan fails at our option, either...
Hunter 82042 Reviews
We have not received any reviews for Hunter yet.