Hunter 82033 Support and Manuals
Get Help and Manuals for this Hunter item
This item is in your list!
View All Support Options Below
Free Hunter 82033 manuals!
Problems with Hunter 82033?
Ask a Question
Free Hunter 82033 manuals!
Problems with Hunter 82033?
Ask a Question
Popular Hunter 82033 Manual Pages
Owner's Manual - Page 1
Installation
Guide
ENGLISH
See page 2
Español
Vea la página 19
Energy Star Bath Fan Models 82033
READ and SAVE THESE INSTRUCTIONS
1
43044-01 03/05/2008
Owner's Manual - Page 2
...THESE INSTRUCTIONS.
2) Before installing, servicing, or cleaning the unit, disconnect the power by turning off position, securely attach a prominent warning device, such as a tag, to the service panel.
3) This unit must be grounded.
4) This appliance is not suitable for Heating, Refrigeration and Air-Conditioning Engineers (ASHRAE), and the local code authorities. See Figure A.
5) Do not install...
Owner's Manual - Page 3
...fan with all applicable codes and standards, including fire-rated construction codes and standards. 8) When cutting or drilling into wall(s) or ceiling, do not damage electrical wiring or other hidden utilities. 9) Do not install this appliance in a tub or shower enclosure. 7) Installation... not install this product in ceilings up to the outdoors. off power unit. 13) Read specification label ...
Owner's Manual - Page 4
...
Included. Check all the parts.
If damaged, call 1-888-830-1326 for replacement. Loosen the fan mounting screws.
4
43044-01 03/05/2008
x3 A
F 95044-01-000 Mounting Rails
G 98141-01-000 H 97134-01-000
Housing
*B *C
3/8" Cable Connector
x2 D
Attachment Screws
x4 E
Mounting Screws
* NOTE: Strain relief (not supplied) cable connector must be installed.
Owner's Manual - Page 5
... to joist, go to step A1, page 5. E
Loosen the wiring cover screw.
Remove the wiring cover. accessible from above, go to step C1, page 9.
Choose Installation Option For New Construction - suspended between, joists go to step B1, page 7. For Existing Construction -
accessible only from the housing. C
D
Remove the...
Owner's Manual - Page 6
.... Section A - New Construction - attaching to joist
A1
OR
Pop out a wiring access slug. A4
A5
3"
Run the power supply wire through the strain relief, leaving
Install the wiring and the strain relief into joist or framing.
Owner's Manual - Page 9
Existing Construction - B10
B11
Install the wiring and the strain relief into the wiring access hole you made earlier. Connect 6" duct and vent to accommodate the new fan housing. accessible from above
C1
NO EXISTING FAN
11"
9 �⁄�"
OR
Remove an existing fan and check to make sure the opening needs to secure...
Owner's Manual - Page 11
secure joints. Tighten
the strain relief around the wire. If ducting does not fit securely, an adapter
may need to the outside. C12
Install the wiring and the strain relief into the wiring access
Connect 6" duct and vent to be purchased.
11
43044-01 03/05/2008 Use duct ...
Owner's Manual - Page 12
... check to make an 11" x 9 5/8" opening
Run the power supply wire through the strain relief, leaving 3"
is no existing fan choose an appropriate location to accommodate the new fan housing. Remove the mounting rail brackets. make sure the opening .
12
43044-01 03/05/2008 Tighten the
there is large enough to...
Owner's Manual - Page 13
... the bottom edge of the housing flush with the sheetrock. If ducting does not fit securely, an adapter
may need to the outside.
D5
D6
Install the wiring and the strain relief into the ceiling.
Screw mounting screws into joist or framing.
13
43044-01 03/05/2008
Use duct tape...
Owner's Manual - Page 14
... wiring cover box. E3
E4
Connect fan wiring harness.
DO NOT ALLOW THE FAN TO HANG FROM THE WIRING HARNESS. Install the wiring cover box.
E5
Install the fan assembly by tightening the two fan mounting screws.
14
43044-01 03/05/2008
Install the strain relief bracket. E6
Secure the fan assembly by inserting the tabs as...
Owner's Manual - Page 15
E9
Complete. E7
E8
Install the bezel by inserting the wire clips into the tabs on the inside of the housing.
Restore power at the source.
15
43044-01 03/05/2008
Owner's Manual - Page 16
..., contact Hunter Technical Support (see Troubleshooting section) to make sure it moves freely.
16
43044-01 03/05/2008 Turn the wall switch off the breaker or removing the fuse. Solution:
• Turn power on . Reinstall the bezel. Test the appliance. Trouble Shooting
Problem: Fan does not come on , replace fuse, or reset breaker. • Hunter Fan Bath Ventilators...
Owner's Manual - Page 17
..., Tennessee. Trouble Shooting (cont.)
If you need parts or service assistance, please call 888-830-1326 or visit us , mishandling, improper installation, modifications or damage to the Hunter Bath Fan while in your possession, or unreasonable use of parts or accessories not authorized by us at our website at http://www.hunterfan.com. If no replacement part can be...
Hunter 82033 Reviews
Do you have an experience with the Hunter 82033 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Hunter yet.
Earn 750 points for your review!