Hunter 82031 Support and Manuals
Get Help and Manuals for this Hunter item
View All Support Options Below
Free Hunter 82031 manuals!
Problems with Hunter 82031?
Ask a Question
Free Hunter 82031 manuals!
Problems with Hunter 82031?
Ask a Question
Popular Hunter 82031 Manual Pages
Owner's Manual - Page 1
Installation
Guide
ENGLISH
See page 2
Español
Vea la página 19
Energy Star Bath Fan Models 82030, 82031, & 82032
READ and SAVE THESE INSTRUCTIONS
42935-01 06/04/2007
Owner's Manual - Page 2
... only. SAVE THESE INSTRUCTIONS.
2) Before installing, servicing, or cleaning the unit, disconnect the power by turning off position, securely attach a prominent warning device, such as a tag, to the outlet box and associated wall switch location. If you cannot lock the circuit breakers in the ceiling. See Figure A.
5) Do not install this manual. min. (0.91 m) Tub...
Owner's Manual - Page 3
...fan with all applicable codes and standards, including fire-rated construction codes and standards.
8) When cutting or drilling into wall(s) or ceiling, do not block air intakes or exhaust in any is used by qualified person(s) in ceilings up to a 12/12 pitch (45 degrees). off power unit.
13) Read specification...other hidden utilities.
9) Do not install this unit is left operating and ...
Owner's Manual - Page 4
... Screws Bezel
Included. Before Installation
A
Tools Needed. (Not supplied.) Estimated assembly time: 30 to 60 minutes
B
Turn off the power source.
42935-01 06/04/2007
Loosen the fan mounting screws.
Check all the parts. If damaged, call 1-888-830-1326 for replacement. x3 A
F 95044-01-000 Mounting Rails
G 97128-01-000 H 97517-01...
Owner's Manual - Page 5
C
D
Remove the fan assembly from below, go to step D1, page 12.
42935-01 06/04/2007
suspended between, joists go to step A1, page 5.
For New Construction - accessible only from the housing. Remove the wiring cover. E
Loosen the wiring cover screw. Choose Installation Option For New Construction - attaching to joist, go to...
Owner's Manual - Page 6
... of your sheetrock.
attaching to joist
A1
OR
Pop out a wiring access slug.
Tighten the strain relief around the wire.
42935-01 06/04/2007
Install the wiring and the strain relief into joist or framing. A2
A3
5/8
5/8
1/2
1/2
Position the correct depth mark at the bottom edge of the joist based...
Owner's Manual - Page 7
... secure joints. Use duct tape to be purchased. suspended between joists
B1
OR
Pop out a wiring access slug. Connect 4" duct and vent to Section E Final Installation on page 14.
Section B - New Construction -
Note the orientation of of the outer ends of your sheetrock.
42935-01 06/04/2007
Position the correct...
Owner's Manual - Page 9
... to be 11" x 9 5/8".
42935-01 06/04/2007 Section C - Use duct tape to Section E Final Installation on page 14. If ducting does not fit securely, an adapter
may need to accommodate the new fan
housing.
B10
B11
Install the wiring and the strain relief into the wiring access hole you made earlier. Connect...
Owner's Manual - Page 11
C12
Install the wiring and the strain relief into the wiring access hole you made earlier. Use duct tape to be purchased.
11
42935-01 06/04/...
Owner's Manual - Page 12
Tighten
the strain relief around the wire.
If there is large enough to accommodate the new fan housing. Use a second wiring access plug if needed. Existing Construction - Go to Section E Final Installation on the top of the wire and the strain relief. accessible from below
D1
D2
Remove one of the wiring access...
Owner's Manual - Page 13
...Move the housing into the wiring access hole you made earlier. Go to the outside.
D5
D6
Install the wiring and the strain relief into the ceiling. D9
5/8
5/8
1/2
1/2
Position the bottom... framing.
13
42935-01 06/04/2007 D7
Connect 4" duct and vent to Section E Final Installation on page 14.
Use duct tape to be purchased. If ducting does not fit securely, an adapter
may need ...
Owner's Manual - Page 14
... the housing mounted to a joist or suspended between the fan assem- DO NOT ALLOW THE FAN TO HANG FROM THE WIRING HARNESS.
E5
Install the fan assembly by tightening the two fan mounting screws.
42935-01 06/04/2007
14
Install the strain relief bracket. E6
Secure the fan assembly by inserting the tabs as shown.
Final...
Owner's Manual - Page 15
Restore power at the source.
15
42935-01 06/04/2007 E9
Complete. E7
E8
Install the bezel by inserting the wire clips into the tabs on the inside of the housing.
Owner's Manual - Page 16
... interior. NEVER IMMERSE METAL OR ELECTRICAL COMPONENTS IN WATER. Trouble Shooting
Problem: Fan does not come on , replace fuse, or reset breaker. • Hunter Fan Bath Ventilators are making excessive or unusual noises, contact Hunter Technical Support (see Troubleshooting section) to make sure it matches the wiring diagram. Problem: Fan is secure. • Check the flapper to clean...
Owner's Manual - Page 17
... INCIDENTAL DAMAGES. To obtain servicing, contact Hunter Fan Company Technical Support at any Hunter Bath Fan which were caused by repairs by persons not authorized by us, use of charge. If we will return your Hunter Bath Fan is not purchased and installed in China
17
42935-01 06/04/2007 If your Bath Fan or provide a replacement free of parts or accessories not authorized by...
Hunter 82031 Reviews
We have not received any reviews for Hunter yet.