Hunter 23849 Support and Manuals
Get Help and Manuals for this Hunter item
View All Support Options Below
Free Hunter 23849 manuals!
Problems with Hunter 23849?
Ask a Question
Free Hunter 23849 manuals!
Problems with Hunter 23849?
Ask a Question
Popular Hunter 23849 Manual Pages
Installation Guide - Page 1
...install the support brace and outlet box. Fan Support System
Fan Support System
Suitable Existing Fan Site
Wiring
Outlet Box
Hunter Fan Company
Step 2 Cut the Ceiling Hole
2-1.
Attach a 2" x 4" support... instructions to install your fan manual and begin with 2 • Installing the Ceiling Plate. Tools and Supplies You May Need
• Drill • Keyhole saw • 2' x 4' support ...
Owner's Manual - Page 1
For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual. Model Name
Model No.
Date Purchased
Where Purchased
Type 2A Models
Owner's Guide and Installation Manual
English
Español
Form# 42888-01 20100301 ©2010 Hunter Fan Co.
Owner's Manual - Page 2
...12 8 • Operating and Cleaning Your
Ceiling Fan 14 9 • Troubleshooting 15
Welcome
Your new Hunter® ceiling fan is an addition to your records and warranty assistance, record information from the carton and Hunter nameplate label (located on the top of the fan motor housing).
SAVE THESE INSTRUCTIONS.
• Use only Hunter replacement parts. • To reduce the risk of...
Owner's Manual - Page 3
If you want to use an existing fan site, complete the following checklist to building structure.
• Fan support system will hold full weight of the fan and light kit.
If your new Hunter fan. Choose the Fan Site
Proper ceiling fan location and attachment to Section 2 • Installing the Ceiling Plate. Ceiling Hole
• e outlet box clearance hole is directly below...
Owner's Manual - Page 4
... to allow you cannot lock the circuit breakers in accordance with wiring, use the hole to the service panel.
5-2. read the fan supply line through the inner holes of the ceiling. For instructions to install your ceiling fan, go to the support brace or joist with an approved connector, available at least 6" beyond the box.
5-3. Cut the...
Owner's Manual - Page 5
... can be used on ceilings less than 8 feet high
Understanding Mounting
Hunter's patented mounting system provides you maximum ease in installing your Hunter fan, use only the hardware supplied.
5 42888-01 • 03/01/10 • Hunter Fan Company This fan was designed to the support structure of your fan. To install and use the accessories, follow the instructions included with each...
Owner's Manual - Page 6
....
Refer to the included Parts Guide. If you are missing or damaged, contact your fan to avoid damage to the fan parts. If you need the following : • Locate the ceiling joist or other suitable support in sets, as they were shipped.
6 42888-01 • 03/01/10 • Hunter Fan Company
1 • Getting Ready
To install a ceiling fan, be sure you can...
Owner's Manual - Page 7
.../10 • Hunter Fan Company
Step 2-2 Canopy Screw Step 2-3
Steps 2-4 - 2-6 The pilot holes should be 9/64" in diameter. Position the isolators between the hanger bracket and ceiling by turning off ...installing your fan, disconnect the power by inserting the raised areas on each end of the hanger bracket, as a tag, to the service panel.
2-1. Drill two pilot holes into the wood support...
Owner's Manual - Page 8
...
Locking Screw
8 42888-01 • 03/01/10 • Hunter Fan Company
Holding the wires out of the large opening in the fan falling.
3-3. Position the square hanger so that the green ground wire attached to do so could result in the ceiling plate. Install two locking screws through the holes in the metal bracket...
Owner's Manual - Page 9
...-01 • 03/01/10 • Hunter Fan Company Connect the bare or green ground wire (grounding) from the ceiling to the white wire (grounded) from the fan
CAUTION: Be sure no bare wire or wire...switch in accordance with national and local electrical codes. 4-1. 4 •Wiring the Fan
All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. To connect the...
Owner's Manual - Page 12
Align the keyhole slots in the housing with this fan model. 7-1. Tighten all three assembly screws could cause improper... firmly. Housing Assembly Screw
Plug Connector Detail
12 42888-01 • 03/01/10 • Hunter Fan Company 7 • Completing Your Installation With a Multi Staked Light Fixture
WARNING: Use only the light fixture supplied with the housing assembly screws...
Owner's Manual - Page 13
... style and number of lights may vary.
7-6. Tighten the thumbscrews securely.
7-8. Shade
Bulb Thumbscrews
Steps 7-7 - 7-8
13 42888-01 • 03/01/10 • Hunter Fan Company To install each ).
Raise the shade to the light fixture. Install the included B10 candelabra-based light bulbs (60 Watt maximum each shade, first loosen the three thumbscrews.
7-7.
Owner's Manual - Page 14
... warm weather to cool the room with Hunter's Dust
Armor protection, making the blades less likely to prevent scratching. The chain has two settings: ON and OFF.
8-4. The fan pull chain controls power to clean the
blades. The blades on the blades. 8 • Operating and Cleaning Your Ceiling Fan
8-1. In warm weather, use an artistic...
Owner's Manual - Page 15
..., use the enclosed balancing kit and instructions to an approved speed control. 5. Tighten the blade bracket screws until snug. 3. Check and tighten the screws in the switch housing mounting plate and in the switch housing. 4.
If so, replace all blade and/or blade iron screws. Problem: Excessive wobbling. 1.
fan does not move. 1. Turn power...
Parts Guide - Page 1
THIS PARTS GUIDE IS FOR REFERENCE ONLY.
REFER TO THE INSTALLATION MANUAL FOR FULL ASSEMBLY INSTRUCTIONS. If parts are included in the box. Dwg. #
Finish Qnty
1 4 2 2 4 4 2 1 1 11 1 1
23849 99606-01 Provencal Gold
Part # 73862-01 74508-37 03144-03 06512-01 06301-01 67290-01 74508-06 99791-05 G0253-45 63755-05 65666-01 99606-00-860
...
Hunter 23849 Reviews
We have not received any reviews for Hunter yet.