Hunter 22462 Support and Manuals
Get Help and Manuals for this Hunter item
View All Support Options Below
Free Hunter 22462 manuals!
Problems with Hunter 22462?
Ask a Question
Free Hunter 22462 manuals!
Problems with Hunter 22462?
Ask a Question
Popular Hunter 22462 Manual Pages
Installation Guide - Page 1
... fan manual and begin with 2 • Installing the Ceiling Plate. If you are essential for Existing Fan Site
If you want to use the hole to the fan supply line leads and associated wall switch location are at least 7 feet above the ceiling hole.
o Six inches of 1/16" into ceiling. Fan Support System
Fan Support System
Suitable Existing Fan Site
Wiring
Outlet Box
Hunter Fan...
Owner's Manual - Page 1
Model Name
Model No.
Date Purchased
Where Purchased
Type 2 Models
Owner's Guide and Installation Manual
English
Español
Form# 42600-01 20100622 ©2010 Hunter Fan Co. For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual.
Owner's Manual - Page 2
.... • To reduce the risk of the fan motor housing). This installation and operation manual gives you with national and local electrical codes and ANSI/NFPA 70.
SAVE THESE INSTRUCTIONS.
• Use only Hunter replacement parts. • To reduce the risk of personal injury, attach the fan directly to the
support structure of the building according to supply you complete...
Owner's Manual - Page 3
... holes of outlet box.
• The outer holes of lead wires extend from outlet box. Fan Support System
Fan Support System
Suitable Existing Fan Site
Wiring
Outlet Box
3 42600-01 • 06/22/10 • Hunter Fan Company Preparing the Fan Site
Step 1 - Ceiling Hole
• The outlet box clearance hole is suitable, skip ahead to determine if the...
Owner's Manual - Page 4
...fan manual and continue with an approved connector, available at least 6" beyond the box.
5-3. Preparing the Fan Site (continued)
Step 2 - Install a Support Brace, If Necessary
Determine if there is positioned to allow you to the outlet box with Section 2 • Installing the Ceiling Plate. Install the Outlet Box
4-1. For instructions to install your ceiling fan, go to the support...
Owner's Manual - Page 5
... quiet and optimum performance of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angled mounting. The steps in one of your Hunter fan in this manual include instructions for ceilings less than 8 feet, you maximum installation flexibility and ease. Support Brace
Ceiling Outlet Box
For ceilings higher than 8 feet high
CAUTION: To reduce the risk...
Owner's Manual - Page 6
... 1 • Getting Ready
To install a ceiling fan, be sure you can direct you to the included Parts Guide. Check for any parts are missing or damaged, contact your Hunter fan dealer can do the following tools for installing the fan: • Electric drill with 9/64" bit • Standard screwdriver (magnetic tip recommended) • Phillips-head screwdriver (magnetic tip recommended) •...
Owner's Manual - Page 7
...
CAUTION: To avoid possible electrical shock, before installing your fan, disconnect the power by turning off position, securely fasten a prominent warning device, such as a tag, to the service panel.
2-1. For Angled Ceilings: Be sure to the outlet box and associated wall switch location. For proper alignment use lubricants on each other. Tighten the screws...
Owner's Manual - Page 8
.../22/10 • Hunter Fan Company For Standard or Angled mounting: 3-2. Insert the downrod through the downrod on
the ceiling plate. 3-8. Note: When the pipe and ball assembly is fully installed, 2-3 threads on the threads. Do not remove this is replaced with three low profile screws.
Hanging the Fan: Note: To hang the fan, you must tilt...
Owner's Manual - Page 10
... canopy.
Swing the fan up to align the canopy screw holes with the screw holes aligned, partially install two canopy screws into the hole between the two ceiling plate tabs.When all... 5-3 Canopy Canopy Trim Ring
Canopy Screw
10 42600-01 • 06/22/10 • Hunter Fan Company Note: Should you use a magnetic tip screwdriver for alignment.
5-3. Verify that must remain engaged...
Owner's Manual - Page 12
... switch housing mounting plate. Once you have uninstalled the light fixture, continue with this fan model.
7-1. This feature gives you are firmly situated in the housing with an integrated light... the center opening of installing the fan with step 7-6 now. Steps 7-1 - 7-3
Housing Assembly Screw
Upper Switch Housing
12 42600-01 • 06/22/10 • Hunter Fan Company WARNING: Use only...
Owner's Manual - Page 13
...connector in fire hazard or improper operation. Exceeding that limit or the marked limit on this ceiling fan contains a device that restricts the light kit to the product.
7-7.
Incorrect connection could cause... Detail
Housing Assembly Screw
13 42600-01 • 06/22/10 • Hunter Fan Company Note: Both plug connectors are properly aligned before connecting them. Align the ...
Owner's Manual - Page 16
... room without causing a draft.
8-5. Clean wood finish blades with a direct breeze. Restart fan. 8 • Operating and Cleaning Your Ceiling Fan
8-1. Turn on the fan to the fan. For cleaning finishes, use a soft brush or lint-free cloth to the fan.
8-2. In winter, having the fan draw air upward (clockwise blade rotation) will damage the finish. Remove surface...
Owner's Manual - Page 17
... of light bulbs installed match the specifications on this fan shuts off at http://www.hunterfan.com.
Problem: If the light on the light socket.
Pull the pull chain to balance the fan. 2.
fan does not move. 1. If your fan wobbles when operating, use the enclosed balancing kit and instructions to ensure it is cracked.
Hunter Fan Company 7130 Goodlett...
Parts Guide - Page 1
...-04
77646-04
1
07570-01
07570-01
07570-01
07570-01
1
63756-05
63756-05
63756-05
63756-05
Hunter Fan Company • 7130 Goodlett Farms Pkwy. #400 • Memphis, TN 38016 • www.hunterfan.com • 98000-01-725 05-17-2010 • ©2010
REFER TO THE INSTALLATION MANUAL FOR FULL ASSEMBLY INSTRUCTIONS.
Hunter 22462 Reviews
We have not received any reviews for Hunter yet.