Hoover U8181 Support and Manuals
Get Help and Manuals for this Hoover item
View All Support Options Below
Free Hoover U8181 manuals!
Problems with Hoover U8181?
Ask a Question
Free Hoover U8181 manuals!
Problems with Hoover U8181?
Ask a Question
Most Recent Hoover U8181 Questions
How To Change The Agitator Belt?
the belt in my hoover savvy broke a few days ago. i have the replacement belt but i am having issues...
the belt in my hoover savvy broke a few days ago. i have the replacement belt but i am having issues...
(Posted by alphasigs819 10 years ago)
Hoe To Replace The Belt On A U8181-900
(Posted by llsmith5449 11 years ago)
Popular Hoover U8181 Manual Pages
Manual - Page 1
www.hoover.com
®
This product was designed for your purchase! TM
Upright Vacuum Cleaner
by HOOVER
Owner's Manual
ENGLISH § pp.1-12 ESPAÑOL § pág. 14-21 FRANÇAIS § p. 23-30
Thank you for easy assembly (see page 3)
Manual - Page 2
...™ Switch 5 If You Have a Problem 11 Clearing Blockages 12 Important Safeguards 2 Lubrication 11 Maintenance Authorized Service 12 Cleaning filter 8 Emptying Dirt Cup 7 Replacing Powered Hand Tool
Agitator Brush Roll 10 Replacing Power Hand Tool Belt ..10 Replacing Edge Groomers 9 Replacing Headlight 9 Thermal Protector 11 Warranty 12
© 2004 The Hoover Company www.hoover.com...
Manual - Page 3
...and four screws from handle section. Slide handle section onto back of packing materials. Find the parts shown above before disposing of handle. Snap tabs on hose holder (B) into holes on the ...1-6 and 1-7). Click on the "Service" button to find the service outlet nearest you need any assistance:
Visit our website at www.hoover.com.
Hose holder
Cleaner Assembly
1-3
1-4
D
F
H
I ....
Manual - Page 4
...switch is wider than the other). Custom Control™ power switch...™ switch. Tighten ... step on
in the outlet, reverse the plug. CARPET setting -
Cleaner description
2-1 1
2 3
7 6
4 ...
2-2
A
Custom Control™ switch
Plug cord into electrical outlet.... .
How to correct setting for household use
Place ... to upright position.)
BARE FLOOR setting -
Operate cleaner only at voltage...
Manual - Page 5
.... Before reaching edge, push down on carpet and floors; This will prevent rug from clinging to the desired setting. Move cleaner back to lift the cleaner.
Do not lift cleaner using cleaning tools; Guide either side of nozzle parallel to edge of cleaner) and will lift up nozzle so that when you...
Manual - Page 6
... powered hand tool, wipe off dirt with a detergent. J. Attach second wand or tool to wand (L) by pushing it at additional cost)
Push Custom Control™ switch to -reach places.
Cleaning tools may be in the upright position
to activate the automatic "brush roll
OFF" and for upholstered furniture, carpeted stairs and...
Manual - Page 7
... this type of dirt cup lid one full turn. The dirt cup assembly consists of the following parts: Lid (A) Dirt Cup (B) Pre-filter (C) HEPA Cartridge Filter (D) Dirt Opening (E) Handle (F)
...from the HEPA cartridge filter.
Tap side of your cleaner will ensure continued cleaning effectiveness. Replace dirt cup lid. Slide cup into place.
This larger debris will be seen collecting in ...
Manual - Page 8
...detergent. Allow pre-filter to dry thoroughly.
3-8
3-9
3-10
H I ) in "How to replace this filter, ask for additional cleaning. DO NOT tap soft pleated sides of HEPA cartridge filter as...knob of the ends. Replace door.
Snap closed. Do not operate cleaner without the filter in the cup. The filter assembly can be removed for HOOVER part No. 40110009.
Slide filter...
Manual - Page 9
... base type 912 bulb, HOOVER part No. 27313107.
3-13
3-14
Remove lens - Lower handle to replace
When agitator brushes are worn, the agitators should be replaced. Turn cleaner over.
Remove... while turning agitators. New brush rolls can be installed at your nearest Hoover Factory Service Center.
3-19
The edge groomers
When to replace
3-17
M
M
Remove bottom plate
Disconnect cleaner from...
Manual - Page 10
How to pinch brush bristles in guard. Inspect belt to last a long time and is cracked, gouged or broken, it (see following section). 5.
Replace belt
When replacing belt, ask for HOOVER part No. 48414088.
3-21
A
3-22
B
2. To replace bottom plate (A), insert the four tabs on edge of bottom plate into place. 5. Replace brush roll, belt guard, and bottom plate as described in...
Manual - Page 11
... tool brush roll won't turn on BARE FLOOR position.
• Set switch to carpet position
• Agitators are obstructed. • Clear obstruction
Problem: Cleaner won't pick up Possible cause Possible solution • Blockage in turbine channel • Remove blockage. • Broken or worn belt • Replace belt • Low cleaner suction • Check items under "Cleaner...
Manual - Page 12
...
Disconnect powered hand tool from electrical outlet. Service
To obtain approved HOOVER service and genuine HOOVER parts, locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot) by the complete model number when requesting information or ordering parts. (The model number appears on the back of warranty service outlets, write or phone the Consumer...
Hoover U8181 Reviews
We have not received any reviews for Hoover yet.