Honeywell TS8095A Support and Manuals
Get Help and Manuals for this Honeywell item
View All Support Options Below
Free Honeywell TS8095A manuals!
Problems with Honeywell TS8095A?
Ask a Question
Free Honeywell TS8095A manuals!
Problems with Honeywell TS8095A?
Ask a Question
Popular Honeywell TS8095A Manual Pages
Owner's Manual - Page 1
T8095A/Q682 Heating-only Thermostat and Wallplate or Heating/Cooling Thermostat and Subbase
OWNER'S MANUAL
D.F. • Rev. 10-94 • • ©Honeywell Inc. 1994 • Form Number 69-0639-1 M3375 T8095A/191108AJ; TS8095A/191108AC;
Owner's Manual - Page 2
... in the trash. The Honeywell name is replacing a control that contains mercury in a sealed tube, do not place your local waste management authority for years to use your assurance of accurate control and reliable operation for instructions regarding recycling and the proper disposal of this control is your new thermostat. Read this manual to learn how to come...
Owner's Manual - Page 3
Table of Contents
Page Features of Your Thermostat ...4 Setting the Temperature ...7 Setting Subbase Switches ...8 Inserting Clock Batteries ...9 Setting the Clock ...10 Programming ...11 Troubleshooting ...15 Servicing the Thermostat ...23
Cycle Rate Adjustment ...23 Thermometer Adjustment ...24 Warranty ...27
3
69-0639-1
Owner's Manual - Page 5
... dark band to indicate nighttime.
13 MANUAL PROGRAM ADVANCE BUTTON. Insert into 24-hour clock dial slots to match the heating system primary control current.
16 MERCURY BULB AND BIMETAL ...ELEMENT (2). Allows change from comfort to match the heating system current draw in amperes.
15 ANTICIPATOR SETTING LEVER. Calibrated to energy savings setting ...
Owner's Manual - Page 6
Provides
mounting base, wiring connections and
manual switching control for additional information.
18
6
R
G
FAN ON
AUTO
O B W
Y
HEAT
COOL OFF
M1809 only or cooling-only thermostat.
18 Q682 SUBBASE (not included with
thermostat; ordered separately). See Setting Subbase Switches
section for heating/cooling
17
thermostat.
17 191108 WALLPLATE. Provides mounting
base and ...
Owner's Manual - Page 8
... detent over desired function indicator mark for proper circuit operation.
8
Setting Subbase Switches (If Applicable)
The subbase system switch controls system operation as controlled by the plenum fan switch. In electric heat, heat pump and fan coil systems, the fan is controlled by the
thermostat. OFF-Both the heating and cooling sytems are
off . If...
Owner's Manual - Page 11
...
PROGRAM PIN SLOT PROGRAM INDEX WHEEL
MANUAL PROGRAM ADVANCE BUTTON
PROGRAM PIN STORAGE
TIME INDICATOR
ARROW
M7319
Fig. 4-Program Components.
11
69-0639-1 FLIP-UP COVER
24-HOUR PROGRAM DIAL (GRAY AREA FOR NIGHT SETTINGS
Before setting your program
■ Lift thermostat flip-up cover to automatically lower and raise the temperature one or...
Owner's Manual - Page 14
Start or End Programs with Manual Program Advance Button
IMPORTANT: To prevent damage to the normal setting. Press the button to immediately begin an energy ...desired mode. The manual program advance button enables immediate, one-time-only program changes to assure the system is in effect. After pressing the button, check the program indicator on the thermostat cover to accommodate temporary...
Owner's Manual - Page 16
...assistance. position of thermostat set point levers.
-
Reset to desired operating position. Move to desired temperatures.
Turn clock ahead 12 hours.
Refer to desired settings. Troubleshooting (Continued)
Problem
Check - Temperature ... of subbase system switch (heating-cooling model).
16
Action
Contact a qualified service technician for correct time locations.
-
Owner's Manual - Page 17
... service technician. thermostat circuits.
17
Action
HEATING-ONLY SYSTEM-Move temperature setting levers 5° F [3° C] above room temperature. Cooling system should start . With system
(Continued)
69-0639-1 HEATING/COOLING SYSTEM-With system switch at HEAT, move temperature setting levers 5° F [3° C] above room temperature. Troubleshooting (Continued)
Problem
Room...
Owner's Manual - Page 18
... system should start. If the system does not operate, call a qualified service technician. Decrease anticipator setting by 0.05.
Check
Burner-on time too long. No cooling. 1
- fuse or circuit breaker. Observe burner operation.
Move switch to COOL position. Troubleshooting (Continued)
Problem
Room temperatures are not correct (continued).
system switch.
See page 8. Observe...
Owner's Manual - Page 19
... terminal screws. -
area around thermostat for assistance. Contact a qualified service technician for drafts or radiant heat. Reinstall thermostat wallplate or subbase. thermostat connections. Turn OFF power to ON position.
Use a spirit level. Action Move to cooling system.
Troubleshooting (Continued)
Problem No cooling 1 (continued). Repair any frayedor broken wires. level...
Owner's Manual - Page 21
... power to power clock, or install backup batteries as shown on model used in heating-only system.
2 Not applicable on page 9. backup batteries may be clogged.
If this Troubleshooting section has not solved the problem, call a qualified service technician or Honeywell Assistance Center, 1-800-468-1502, Monday-Friday, 7:00 a.m. Check
-high limit control.
See page 9.
1 Not applicable...
Owner's Manual - Page 23
NOTE: Most hot water systems require a setting of 1.2A.
ANTICIPATOR SCALEPLATE
ANTICIPATOR SETTING LEVER
M7317
Fig. 6-Heat Anticipator Setting.
23
69-0639-1
Servicing the Thermostat
Cycle Rate Adjustment (T8095A only)
The equipment should cycle on and off just enough to keep the room temperature close to cycle the heating system too fast or too ...
Owner's Manual - Page 28
Honeywell Limited-Honeywell Limitée
1985 Douglas Drive North
35 Dynamic Drive
Golden Valley, MN 55422
Scarborough, Ontario M1V 4Z9 Automation and Control Solutions
Honeywell International Inc.
Honeywell TS8095A Reviews
We have not received any reviews for Honeywell yet.