Honeywell RCWL8000 Support and Manuals
Get Help and Manuals for this Honeywell item
View All Support Options Below
Free Honeywell RCWL8000 manuals!
Problems with Honeywell RCWL8000?
Ask a Question
Free Honeywell RCWL8000 manuals!
Problems with Honeywell RCWL8000?
Ask a Question
Popular Honeywell RCWL8000 Manual Pages
Owner's Manual - Page 1
Installation and Use
VISIOCAMTM RCWL8000A and RPWL800A
Wireless Video Chime System
69-2108EFS_A.indd 1
69-2108EFS-01
11/30/2007 1:51:44 PM
Owner's Manual - Page 2
... and that you have chosen! (See 'Setting up 2 Pre-installation Setup 2
Installing the Door Camera 4 Door Camera TransformerOption 7
Installing the receiver 8 Receiver Operation 8 Door Camera 10
Expanding Your System 11
Maintenance and Use 12 Care and Maintenance 12 Replacing the Receiver Batteries 12 Troubleshooting 13
Specifications 15 Declaration 16 Disposal and Recycling 16...
Owner's Manual - Page 3
... LOOKS FOR CONNECTED CCTV-TYPE CAMERAS
Pre-installation setup
Before fixing the door camera in place, set up and test the system as follows:
Install the batteries in the door camera
Note: ... LIGHTING AND SWITCHES CAMERA FROM COLOR TO MONOCHROME IN LOW LIGHT
RECEIVER FEATURES
DISPLAY
- Features
VISIOCAM
DOOR CAMERA FEATURES
INFRARED LEDS - NAMEPLATE
3 12
69-2108EFS_A.indd 1
69-2108EFS-...
Owner's Manual - Page 4
.../2007 1:51:45 PM See 'Door 1
Camera Transformer option' at the end of the strip and carefully push it back into the slot.
2. Installation and Use
Pre-installation setup
Note: Removing the cover also provides access to the nameplate, so now is an option to power the door
camera using an 8-10V transformer.
Owner's Manual - Page 5
...tunes play once the batteries have enough power for approximately two minutes. VISIOCAM
2
Program the door camera into the receiver, the receiver remains active ...1 for at least three hours so that the charging base and rear of the portable receiver.
2. Pre-installation setup
Charge the receiver batteries
1.
The battery indicator flashes slowly if this is the first time the unit has been...
Owner's Manual - Page 7
... of the product. The units may need to adjust the camera lens to the troubleshooting section for example, CH 3. Open the back of the door camera and adjust the camera eyeball from CH 1 to page 3). Installing the door camera
VISIOCAM
Position the receiver
The receiver must be too far apart (more than 60...
Owner's Manual - Page 8
... horizontally and 3.6 in place using the camera base as moisture or condensation will affect the internal parts. Remove the two screws underneath the door camera. Unhook TOP and release the front and pull...the screws and wall plugs provided.
4. The distance between mounting holes is working after installation by pressing the call button, the confidence light should illuminate.
69-2108EFS-01
...
Owner's Manual - Page 9
..., for later service access. Leave about 6 in to a suitable, always on, mains supply.
Do not fit batteries.
2.
Connect the mains terminals of the transformer TO THE
to seal the unit against rain damage.
3. Important: Higher voltage transformer might damage the camera. Secure the door camera in place. Follow the transformer instructions carefully for...
Owner's Manual - Page 10
... Use
Installing the receiver
Receiver operation
When the call button is pressed on the door camera, the receiver chimes (provided
the volume switch is not set to conserve cam- Charging base
CHIME...button, then adjust the receiver display for sound). era battery life and is the recommended setting. the chime alone sounds (unless the battery
DISPLAY BRIGHTNESS
level is on the charging ...
Owner's Manual - Page 11
... uses the public airwaves, and that follows the chime when a visitor presses the call button. Replace the batteries in a multi-camera system, this with a double beep warning tone that the 30...the caller, so they can be viewed on the front of a low battery alert. Installing the receiver
VISIOCAM
Chime tune selection
The receiver chime tune can be changed by nearby 2.4GHz video receiving...
Owner's Manual - Page 13
... up to clear the programmed data and enter programming mode.
Expanding your system
VISIOCAM
There are many ways to expand your entry system: you can connect the receiver to a TV set via the accessory RCA lead provided. Refer to the instructions provided with the additional unit, or see 'To reprogram or reset the...
Owner's Manual - Page 14
... not place rings or other metal objects over the peg in the charging unit -
Installation and Use
Maintenance and use will eventually reduce the capacity of the rechargeable batteries, and... camera, as it may damage the internal parts.
• Avoid replacing door camera batteries during wet weather.
• Do not take the products apart; Replace the batteries by unscrewing the
single battery...
Owner's Manual - Page 15
...adjacent
object, or is facing a very black surface.
Replace the door camera batteries.
13
69-2108EFS-01
69-...or others), every unit must have its video channel switch set to see 'Pre- The receiver battery indicator will stay on...problem, move the receiver 20 in the door camera. installation Setup' on the front does not light when the call button is pressed. Troubleshooting
VISIOCAM...
Owner's Manual - Page 17
...-size NiMH batteries, minimum 1200mAh
Battery operating life
typically one year*
typically 3 days from full charge*
Motion sensor range
12 ft. (4 m) typical (fixed sensitiv- ASpbeocuitfiycoautironnesw thermostat
VISIOCAM
Door Camera
Receiver
Power requirement
110V AC ±10% via 8V to 10V 1A bell transformer** N/A or 8-12V AC or DC supply
Maximum number of...
Owner's Manual - Page 18
...
Registered Trademark. © 2007 Honeywell International Inc. 69-2108EFS-01 M.S. 11-07
69-2108EFS_A.indd 16
Printed in CUL and UL60065 safety requirements. DECLARATION Honeywell hereby declares that may not cause ...51:50 PM Check with household waste. The charging base is in compliance with Part 15 of purchase.
This device operation is required; on recycled paper containing at...
Honeywell RCWL8000 Reviews
We have not received any reviews for Honeywell yet.