Honeywell HPF24S8 Support and Manuals
Get Help and Manuals for this Honeywell item
View All Support Options Below
Free Honeywell HPF24S8 manuals!
Problems with Honeywell HPF24S8?
Ask a Question
Free Honeywell HPF24S8 manuals!
Problems with Honeywell HPF24S8?
Ask a Question
Most Recent Honeywell HPF24S8 Questions
Nac Eol Fault Tolerance
At what EOL "resistance" does a class B nac output going into open fault or short fault?
At what EOL "resistance" does a class B nac output going into open fault or short fault?
(Posted by jettymain1992 1 year ago)
Popular Honeywell HPF24S8 Manual Pages
Installation Instructions - Page 2
...installed in the same room as epilepsy.
• Studies have been properly maintained and replaced regularly. Audible warning devices such as required by National and/or local fire codes...-floor detector, for service with your control panel...and instruct them ...manual pull stations, ... the Guides for fire...2007
HPF24S Series Power Supplies - Such ...batteries only for the connection of all installing...
Installation Instructions - Page 3
...B of Part 15 of Echelon Corporation.
Disconnect AC power and batteries prior to the following will be tested and proper system operation verified. FACP operation and reliability depend upon proper installation.
ARCNET® is required after any modification, repair or adjustment to radio communications. All rights reserved. Disconnect all registered trademarks of Honeywell...
Installation Instructions - Page 4
... contact Technical Services.
4
HPF24S Series Power Supplies - If you have any questions about our online Help or printed manuals, you think should be improved or corrected •Your suggestion for how to correct/improve documentation
Send email messages to:
FireSystems.TechPubs@honeywell.com
Please note this email address is for a specific application.
Contact Technical Support with...
Installation Instructions - Page 9
... in this manual also applies to the Canadian versions of the power supplies.
1.1 General
The HPF24S power supplies can be configured as the HPF24S6 and HPF24S8 respectively. The power supplies are triggered by the reverse polarity of the power supplies. Output circuits may be configured to power four noncoded or coded NACs. AC fail, battery, charger and ground fault troubles will...
Installation Instructions - Page 10
...one hour maximum): - 6.0 amps for HPF24S6 - 8.0 amps for HPF24S8 • Integral supervised battery charger for lead acid batteries only • Capable of charging 7.0 AH to 18.0 AH (Amp Hour) batteries • Fully supervised power supply, battery and NACs • Selectable Strobe Synchronization for NACs (System Sensor, Gentex, and Wheelock) • Coded signal synchronization • Fixed...
Installation Instructions - Page 11
...used for terminal locations. indicates a Notification Appliance Circuit trouble (blinks once for Circuit 1 trouble, twice for Circuit 2 trouble, three times for Circuit 3 trouble and four times for zero impedance between the power supply and ground. TB1
• HPF24S6 & HPF24S8: 120 VAC, 60 Hz, 3.2 amps maximum • HPF24S6E & HPF24S8E: 240 VAC, 50 Hz, 1.6 amps maximum
HPF24S Series...
Installation Instructions - Page 12
... Capacity: 18.0 AH • Minimum Battery Capacity: 7.0 AH • Power supply draws maximum standby current of -Line Resistors) or Style Z NACs using the optional ZNAC-4 Class A converter module
OR -
Four resettable or nonresettable 24 VDC power outputs • Refer to the Device Compatibility Document for all outputs: HPF24S6 - 6.0 amps HPF24S8 - 8.0 amps • Output Circuit Types...
Installation Instructions - Page 26
... 4 set to stabilize. A battery fail condition at the power supply
- Trouble Relay will prevent AC loss from being reported as a trouble). When a host FACP is accomplished by setting SW1 DIP switch 4 to delay the reporting of SW1 DIP switch 4.
26
HPF24S Series Power Supplies - P/N 52751:D3 5/11/2010 If more than one in this figure, refer to the SLC manual...
Installation Instructions - Page 33
... 4 amps of continuous current and the HPF24S8 can also be configured as the Aux. As an alternative, the trouble contacts at TB5 of the HPF24S. P/N 52751:D3 5/11/2010
33 Output circuits 1 & 2 are configured as nonresettable power outputs by setting the power supply for independent trouble monitoring.
2.
When the HPF24S power supply is dependent on the control module output...
Installation Instructions - Page 37
... extender only.
P/N 52751:D3 5/11/2010
37 NAC Outputs only Cut JP1
24fsCanadiantpH.wmf
Battery -
The Ground Fault Detection circuit on the HPF24S power supply must be used as auxiliary power outputs.
• The host FACP must be connected to the SLC manual appendix, which contains wiring conversion charts for all ground fault conditions. HPF24S...
Installation Instructions - Page 38
... all internal and external devices continuously during the non-fire alarm condition. The power supply must support a larger load current during a primary power loss. The secondary power source (batteries) must be able to operate the system 2. Calculating the total amount of batteries required to power the system during a fire alarm condition. This branch circuit must connect to the...
Installation Instructions - Page 41
... Factors, depending on the Protected Premises label located inside the cabinet door.
Batteries larger than 7 AH require the BB-17 or other UL listed external battery cabinet.
Calculating the Battery Size
Power Supply Requirements
5. P/N 52751:D3 5/11/2010
41 The power supply can charge batteries in Table 6.4 . Secondary Standby Load
Required Standby Time
(total from Table...
Installation Instructions - Page 42
...
1.07
276
174
109
69
138
87
55
34
Table A.1 NAC Wiring Requirements for Power Supply
Calculations are based on Direct-Current Resistance data for each circuit. The following table lists NAC wiring requirements for the HPF24S6 and HPF24S8 Field Charger Power Supply. Appendix A: Wire Requirements
Connecting external system accessories to the main circuits must be carefully...
Installation Instructions - Page 48
...
E
ELR installation 25 see also End-of-Line Resistor 25
End-of-Line Resistor see also ELR 25
F
faults 25 Features 9 filtered power 9 float charge voltage 12 Form-C
see also Relay 10
G
Gentex - 24VDC 44 ground fault 9
ground fault detection 10, 11
Jumper JP1 11 ground fault LED 11
H
HPF24S6 9
48
HPF24S Series Power Supplies...
Installation Instructions - Page 49
...
I-S
HPF24S8 9
I
input current 12 voltage 12
input circuit 9 activation 9 compatibility 9 see also control 12
installation 15
J
JP1 Jumper ground fault detection 11
JP2 Jumper Coded/Noncoded Input 11
JP3 Jumper Coded/Noncoded Input 11
Jumper
JP1 ground fault detection 10, 11
JP2 Coded/Noncoded Input 11 JP3 Coded/Noncoded Input 11
L
LED AC power 11 battery/charger trouble 11...
Honeywell HPF24S8 Reviews
We have not received any reviews for Honeywell yet.