Honeywell 4600GHD051CE Support and Manuals
Get Help and Manuals for this Honeywell item
View All Support Options Below
Free Honeywell 4600GHD051CE manuals!
Problems with Honeywell 4600GHD051CE?
Ask a Question
Free Honeywell 4600GHD051CE manuals!
Problems with Honeywell 4600GHD051CE?
Ask a Question
Popular Honeywell 4600GHD051CE Manual Pages
User Guide - Page 2
... is operated in a commercial environment.
No part of this document may cause undesired operation. This equipment has been tested and found to comply with the limits for technical or editorial errors or omissions contained herein; Disclaimer
Honeywell International Inc. ("HII") reserves the right to make changes in specifications and other companies and are the property...
User Guide - Page 7
Terminal Interfaces
Terminal ID 2-1 Supported Terminals 2-2 Keyboard Country 2-4 Keyboard Style 2-6
i Table of Contents
... Connection 1-12 Wand Emulation Connection 1-13 Menu Barcode Security Settings 1-14 Reading Techniques 1-15
Chapter 2 - Getting Started
About This Manual 1-1 Unpacking the Imager 1-1 Imager Models 1-2 Imager Identification 1-3 Connecting the Imager with Keyboard...
User Guide - Page 14
... 14-1 Inspecting Cords and Connectors 14-1 Replacing the Interface Cable 14-2 Troubleshooting 14-4
Chapter 15 - Customer Support
Technical Assistance 15-1 Online Technical Assistance 15-1
Product Service and Repair 15-2 Online Product Service and Repair Assistance ... 15-2
Limited Warranty 15-3
viii Chapter 12 - Serial Programming Commands
Conventions 12-1 Menu Command Syntax 12...
User Guide - Page 17
... damage during shipment. Report damage immediately to an option indicates the default setting. 1 Getting Started About This Manual This User's Guide provides installation and programming instructions for the most common terminal and communications settings. Product specifications, dimensions, warranty, and customer support information are factory programmed for the 4000 Series imagers.
User Guide - Page 21
... 1-2 to determine which interfaces apply to the USB port of this manual. For additional USB programming and technical information, refer to the com-
An imager can be ...www.honeywell.com/aidc.
1 - 5 Verify the imager operation by scanning a barcode from the Sample
Symbols in the back of a computer. 1.
The imager beeps. 4. Connecting the Imager with USB
Note: See "Imager Models" ...
User Guide - Page 22
...Models" on page 1-2 to determine which interfaces apply to the imager. Use only serial wedge cables to prevent damage to your imager.
1. Program...the imager to the port.
4. Tighten the two screws to secure the connector to work properly, you must have the correct cable...interface using the Plug and
Play barcode on page 2-10 to set the baud rate and communications protocol.
1 - 6 Once the ...
User Guide - Page 30
... terminal ID only, without changing any other imager settings, please refer to the imager. Please contact the nearest technical support office (see Technical Assistance on page 2-12.)
Wand Emulation Plug & Play
(Code 39 Format)
Wand Emulation Plug & Play Same Code
Menu Barcode Security Settings
Honeywell 2D imagers are programmed by scanning menu barcodes or by sending serial commands...
User Guide - Page 45
... = 40.
20
* 40
60
80
2 - 13 Code 39 Format
Same Code Format
Wand Emulation
Note: See "Imager Models" on page 6-2). In Wand Emulation mode, the imager decodes the barcode then sends data in smaller blocks to prevent buffer overflow. Default = Code 39 Format. Note: Changing primary wand emulation settings also changes the secondary wand emulation...
User Guide - Page 57
... Modes are effective in minimizing accidental rereads. You can read a barcode) when the trigger is pulled when using a hands free mode, the imager changes to manual trigger mode. Setting a reread delay protects against accidental rereads of the same barcode. Default = Medium.
3 - 9 Once the time-out value is required. Use shorter delays in...
User Guide - Page 77
...Programming Chart inside the back cover of steps to 0. Scan the Save barcode using the Programming Chart inside the back cover of this manual. You can program... scan the Intercharacter Delay barcode, then set the number of this manual.
4 - 5 User Specified Intercharacter Delay...Save barcode using the Programming Chart inside the back cover of this manual. Intercharacter, Interfunction, ...
User Guide - Page 81
... Send Commands on page 5-2) within the format program to Supported Terminals (page 2-2) and locate the Terminal ID number for your primary data format, or one barcode has been read, the imager reverts to change the imager's output. Specific Term ID, Actual Code ID, Actual Length 2. Specific Term ID, Universal Code ID, Universal Length 5. Universal Term ID...
User Guide - Page 89
... the Same Code Format barcode sets the terminal ID to your imager.
Note: Changing secondary wand emulation settings also changes the primary wand emulation settings (see Wand Emulation on page 6-1 to determine which interfaces apply to 64.
Wand Emulation Same Code Format
Wand Emulation Code 39 Format
Wand Emulation Multi Block
Note: See "Imager Models" on page...
User Guide - Page 93
...- 7 Low Power Time-Out Note: This time-out does not begin until the imager time-out setting has expired. Scan the Hands Free Time-Out barcode, then scan the time-out duration (from 0-... back cover, and Save.
Default = 120 seconds. Programming Low Power Time-Out in the secondary interface also programs it in manual trigger mode by setting the Hands Free Time-Out. If the imager's trigger...
User Guide - Page 100
... than a space. Default = No Check Character.
* No Check Character
Validate, but will transmit this function is set to append the data from each. Refer to the host computer.
The imager transmits the appended data when it reads a Code 39 barcode that start with the scanned data.
Minimum Message Length
Maximum Message Length...
User Guide - Page 194
..., or you aren't sure what programming options are in Manual/Serial Trigger Mode either by scanning the Manual/Serial Trigger Mode barcode (page 3-4), or by sending the Manual/ Serial Menu Command (page 12-9). Selection
Setting * Indicates default
Factory Default Settings
Default
Terminal Interfaces
Terminal ID
000 (4600g/4600r/4600rp/ 4800i 030 models) 124 (4600g/4600r/4600rp/ 4800i...
Honeywell 4600GHD051CE Reviews
We have not received any reviews for Honeywell yet.