Honeywell 4600RSF051C Support and Manuals
Get Help and Manuals for this Honeywell item
View All Support Options Below
Free Honeywell 4600RSF051C manuals!
Problems with Honeywell 4600RSF051C?
Ask a Question
Free Honeywell 4600RSF051C manuals!
Problems with Honeywell 4600RSF051C?
Ask a Question
Popular Honeywell 4600RSF051C Manual Pages
User Guide - Page 2
... found to comply with part 15 of their respective owners.
This device may cause undesired operation. These limits are the property of the FCC Rules. nor for technical or editorial errors or omissions contained herein; All rights reserved.
Disclaimer
Honeywell International Inc. ("HII") reserves the right to make changes in specifications and other companies and...
User Guide - Page 7
... 1-12 IBM 4683 Ports 5B, 9B, and 17 Connection 1-12 Wand Emulation Connection 1-13 Menu Barcode Security Settings 1-14 Reading Techniques 1-15
Chapter 2 - Table of Contents
Chapter 1 - Getting Started
About This Manual 1-1 Unpacking the Imager 1-1 Imager Models 1-2 Imager Identification 1-3 Connecting the Imager with Keyboard Wedge 1-4 Connecting the Imager with USB 1-5 Connecting the...
User Guide - Page 17
... order. • Save the shipping container for the most common terminal and communications settings. Honeywell barcode imagers are also included. If you open the shipping carton, take the following steps: • Check for the 4000 Series imagers. 1 Getting Started About This Manual This User's Guide provides installation and programming instructions for damage during shipment.
User Guide - Page 20
.../computer. 3. Your imager is your interface and you do not need to modify the settings, skip to your imager. Turn the terminal/computer power back on page 1-2 to determine... the imager operation by scanning a barcode from the back of a keyboard wedge connection: 1. If this manual.
Connect the appropriate interface cable to the imager and to the terminal/computer. 2. Output.
1 - ...
User Guide - Page 21
... Application Note," available at www.honeywell.com/aidc.
1 - 5
Verify the imager operation by scanning a barcode from the Sample
Symbols in the back of a computer. 1. For additional USB programming and technical information, refer to the USB port of this manual. Connecting the Imager with USB
Note: See "Imager Models" on page 1-9.
3. Connect the appropriate...
User Guide - Page 22
...the Imager with RS-232 Wedge
Note: See "Imager Models" on page 1-2 to determine which interfaces apply to your imager. Tighten the two screws to secure the connector to wedge into an RS-232 serial ...imager for your computer. Use only serial wedge cables to prevent damage to set the baud rate and communications protocol.
1 - 6 Refer to RS-232 Baud Rate on your
type of terminal...
User Guide - Page 30
Please contact the nearest technical support office (see Technical Assistance on page 2-12.)
Wand Emulation Plug & Play
(Code 39 Format)
Wand Emulation Plug & Play Same Code
Menu Barcode Security Settings
Honeywell 2D imagers are programmed by scanning menu barcodes or by sending serial commands to Wand Emulation Connection on page 15-1) for further information.
1 - 14 If ...
User Guide - Page 45
... changes, but converts all symbologies to Code 39. Code 39 Format
Same Code Format
Wand Emulation
Note: See "Imager Models" on page 6-2). Note: Changing primary wand emulation settings also changes the secondary wand emulation settings (see Secondary Code 39 Wand Emulation on page 1-2 to determine which interfaces apply to Code 128. The Code 39 Format converts all other symbologies...
User Guide - Page 57
If the imager's trigger is required. Setting a reread delay protects against accidental rereads of the same barcode.
Image Snap and Ship
Hands Free Time-Out
The Scan Stand, and Presentation, and Streaming Presentation Modes are effective in minimizing accidental rereads. Use shorter delays in manual trigger mode by default. Once the time-out...
User Guide - Page 77
...the Save barcode using the Programming Chart inside the back cover of this manual.
Note: Intercharacter delays are not supported in 5 ms steps) may be placed after the transmission of a ...intermessage delays slow the transmission of this delay, scan the Intercharacter Delay barcode, then set the number of scanned data. Scan the Intercharacter Delay barcode below , then scan ...
User Guide - Page 89
... delay time between data blocks. Wand Emulation Same Code Format
Wand Emulation Code 39 Format
Wand Emulation Multi Block
Note: See "Imager Models" on page 2-13). The Code 39 Format barcode below sets the terminal ID to 61, and the Same Code Format barcode sets the terminal ID to your imager. Default = 50ms.
5ms 150ms
* 50ms 500ms...
User Guide - Page 93
...when using a hands free mode, the imager changes to manual trigger mode. If the imager's trigger is reset.
You can set the time the imager should remain in seconds). Low Power... from the inside back cover, and Save. Note: If you change the time-out duration (in manual trigger mode by setting the Hands Free Time-Out. Default = 120 seconds. Default = 5,000 ms.
Hands Free Time...
User Guide - Page 100
... append the data from each. Default = Off. When Check Character is set to Validate and Transmit, the imager only reads Code 39 barcodes printed with a check character, and will transmit this function is set to Validate, but Don't Transmit, the unit only reads Code 39 barcodes printed with a check character, but Don't Transmit
Validate...
User Guide - Page 194
... options are in Manual/Serial Trigger Mode either by scanning the Manual/Serial Trigger Mode barcode (page 3-4), or by sending the Manual/ Serial Menu Command...to all imager models.
Selection
Setting * Indicates default
Factory Default Settings
Default
Terminal Interfaces
Terminal ID
000 (4600g/4600r/4600rp/ 4800i 030 models) 124 (4600g/4600r/4600rp/ 4800i 050 models)
Serial Command...
User Guide - Page 203
... Emulation Idle Data Block Size
Secondary Trigger Model
Wand Emulation Same Code Format Wand Emulation Code 39 Format 5 ms *50 ms 150 ms 500 ms On *Off 10 *25 40 80 120 150 200 *Black High White High *Idle High Idle Low 20 *40 60 80 *Manual/Serial Trigger Read Time-Out (0 - 300,000...
Honeywell 4600RSF051C Reviews
We have not received any reviews for Honeywell yet.