HP rp2470 Support and Manuals
Get Help and Manuals for this Hewlett-Packard item
Most Recent HP rp2470 Questions
Fault Light On Boot No Errors In Log
We had a unit that when boots gets a solid fault light with no entry in log
We had a unit that when boots gets a solid fault light with no entry in log
(Posted by jnevico 13 years ago)
HP rp2470 Videos
A6892A HP 750MHz PA-8700 Processor for rp2470 at Genisys
Duration: :33
Total Views: 25
Duration: :33
Total Views: 25
Popular HP rp2470 Manual Pages
CIFS/9000 Client Release Note, June 2002 - Page 12
... in password policies among different PAM modules, password change may get passwords out of modifying the PAM configuration file.
• PAM Stacking may cause problems when used . HP CIFS/9000 Client product includes the PAM NTLM that the administrator is assumed that integrates HP-UX login with the general PAM framework. Consult the user manual Installing and...
HP DLPI Programmer's Guide - Page 11
... with the -r option returns the release identifier. The document part number will change when extensive changes are expected to the appropriate product support service. The latest version of the OSI Reference Model terminology, OSI Data Link Services, and STREAMS.
HP-UX Release Name and Release Identifier
Each HP-UX 11i release has an associated release name and release identifier...
HP DLPI Programmer's Guide - Page 20
...protocol through which layer the services are used throughout this guide.
The model defines networking functionality at several layers and service providers between the layers. ...Service Interface
Each layer of information over a physical communications medium. A model of the data link layer is responsible for the transmission and error-free delivery of bits of the OSI Reference Model...
HP DLPI Programmer's Guide - Page 131
... wishes to ) errors listed in the DL_ERROR_ACK. Chapter 2
131 If the request is erroneous, DL_ERROR_ACK is returned and the resulting state is no immediate response to the connect request. DLPI Primitives Connection-mode Service Primitives
Response There is unchanged. Reasons for Failure DL_BADADDR
The destination DLSAP address was not supported by the callee...
HP DLPI Programmer's Guide - Page 135
... was not associated with a currently open stream. Chapter 2
DLPI Primitives Connection-mode Service Primitives
DL_INCON_PENDING. These streams may be the same when the response corresponds to the ... stream. The UNIX error returned may only be set to (not limited to) errors listed in Table 2-2 on the stream where the DL_CONNECT_RES primitive was not supported by the parameter dl_res_token...
HP DLPI Programmer's Guide - Page 11
... updated or new editions, you should subscribe to correct errors or document product changes. Intended Audience
This manual is printed. The users are made at http://docs.hp.com. Table 1
HP-UX 11i Releases
Release Identifier
Release Name
Supported System
B.11.11 B.11.20 B.11.22
HP-UX 11i v1 HP-UX 11i v1.5 HP-UX 11i v1.6
HP 9000 HP Integrity HP Integrity
11 The document part...
HP DLPI Programmer's Guide - Page 132
The UNIX error returned may be set to (not limited to establish a data link connection. Format The message consists of service parameters contained invalid values. DL_BADQOSPARAM
The quality of one M_PROTO message block containing the structure shown below.
132
Chapter 2 DL_BADQOSTYPE
The quality of service structure type was in Table 2-2 on page 71. DLPI Primitives...
HP DLPI Programmer's Guide - Page 136
..., and the resulting state of service structure type was not supported by the parameter dl_res_token), the resulting state is unchanged.
DL_ACCESS
The DLS user did not correspond to ) errors listed in the DL_ERROR_ACK.
For the responding stream (designated by the DLS provider.
The UNIX error returned may only be set to (not limited to a pending...
rp24xx A180 User Manual - Page 66
... server. Troubleshooting with Light-Emitting Diode (LED) Interpretation
The LED icons shown above are physically located on the right-hand side of selftest failed.
Refer to the Chassis Code Summary section.
If the power source is valid, the problem is applied to identify which takes approximately 2 seconds. A-Class System Service A-Class Server Trouble Shooting
A-Class Server...
rp24xx A180 User Manual - Page 69
... back, lift it off, and set it aside. General RAM Module Troubleshooting.
List which size SIMMs are not the cause of the server.
If fault does not recur, the SIMMs installed in slots 2a/b, the RAM SIMM fault returned. Step 1.
Step 1.
Repeat step 3 until the RAM SIMM fault recurs. Therefore, the problem is
discharged from completing selftest. SIMM...
rp24xx A180 User Manual - Page 70
... set it aside. Replace that I /O Board Fault. Step 3. Power down the server and replace the RAM SIMM in this type of the server. To change the system board, you must be removed from the cabinet before proceeding.
• Remove the top of the server by the HSC Remote Management card are useful to troubleshoot this section require opening the server...
rp24xx A180 User Manual - Page 71
... Faults, power on the PIM data to see if the time recorded corresponds to the time of error, because HPMCs generate many chassis codes and some chassis codes indicate a specific fault.
If replacing the I/O card does not clear the I/O Subsystem or I /O Board faults occur when an HPMC, in the bottom slot is the problem. Check the timestamp on the server and...
rp24xx A180 User Manual - Page 72
... error. Look up the accompanying message and take appropriate action.
WARNING: One or more details, use the 'FASTBOOT' command in troubleshooting this type of stored on the PIM data to see if the time recorded corresponds to boot the OS. A-Class System Service A-Class Server Trouble Shooting
Second Level Cache Memory HPMC Fault.
This condition requires replacing...
rp24xx A180 User Manual - Page 79
.... To acquire write access, press ctrl F12. Troubleshooting Embedded Disks
The A-Class server will support a maximum of the server and remove the LAN cable from an embedded disk, an Input/Output Dependent Code (IODC) error occurs. ENTRY_INIT Status = -10
Chapter 3
79
Also, embedded disks do not have an individual fault LED to initialize. Cannot find ENTRY_TEST
Failed to...
rp24xx A180 User Manual - Page 80
...the disk.
Check disk configuration jumper settings. Password-protected disk expert tools are unfamiliar with part number A5182-69101 or later.
80
Chapter 3 If the embedded disk is applied to ODE and STM software, and disk expert tools. Make sure that power is not recognized by the server's bootstrap software. NOTE
Only licensed self-maintenance technicians and HP service personnel...
HP rp2470 Reviews
We have not received any reviews for HP yet.