HP ProDesk 680 G3 Micro Support and Manuals
Get Help and Manuals for this Hewlett-Packard item
View All Support Options Below
Free HP ProDesk 680 G3 Micro manuals!
Problems with HP ProDesk 680 G3 Micro?
Ask a Question
Free HP ProDesk 680 G3 Micro manuals!
Problems with HP ProDesk 680 G3 Micro?
Ask a Question
Popular HP ProDesk 680 G3 Micro Manual Pages
Getting Started Guide - Page 6
... system 22 Downloading Windows updates ...22 Customizing the monitor display ...22 Turning off the computer ...23 If you encounter issues ...23 Performing basic troubleshooting ...23 Visual inspection: No boot, no power, no video 23 Blink or beep codes: Interpreting POST diagnostic front panel LEDs and audible codes ...24 HP Support Assistant ...24 Using HP PC Hardware Diagnostics...
Getting Started Guide - Page 11
... set in Computer Setup. If you encounter problems with components not diagnosed in the Sleep state, shut down , unplug the power cord, wait a few seconds, and then plug it in diagnostics, and guided assistance. Then press the power button again to the operating system. HP Support Assistant
HP Support Assistant is an HP application that helps you have been installed...
Getting Started Guide - Page 17
... created, and then reinstalls the operating system, programs, and drivers. To prevent loss of the original factory-shipped software. System...installed after recovery. To perform a System
If you have a problem that might be a time-saver if you can restore it after purchase.
Go to http://www.hp.com/support, select your country or region, and follow the on -screen instructions to set...
Hardware Reference Guide 1 - Page 18
... supported
NOTE: The system will have more memory
12 Chapter 2 Hardware upgrades...flex mode, depending on the system board, with up to the following specifications: ● Industry-standard 288-pin ● Unbuffered non-ECC PC4-...DIMM4 operate in memory channel B.
To achieve the maximum memory support, you install unsupported DIMMs.
Populating DIMM sockets
There are four DIMM sockets...
Maintenance and Service Guide - Page 55
...Setup Utilities menu: Main, Security, Advanced, and UEFI Drivers. Turn on password prompt during startup.
A choice of boot sources. ● Configure features such as Secure Boot, power management, virtualization support...an administrator password that controls access to the Computer Setup (F10) Utility and
the settings described in Setup and POST. ● Replicate the system setup by ...
Maintenance and Service Guide - Page 57
... Diagnostics installed, the application will launch. Computer Setup (F10) Utilities 49 Lists smaller subset if Basic System Information is selected.
Computer Setup-Main
NOTE: Support for specific Computer Setup options may vary depending on the setting in following functions: ● Memory Test ● Hard Drive Check ● Language
Lets you update the system BIOS from www.hp.com...
Maintenance and Service Guide - Page 61
...: Support for Computer Setup.
● Fast Boot.
Default is enabled. This feature wakes the system up are suppressed.
● UEFI Boot Order.
Default is forced to 'Power On from errors, warnings, and password prompts during a service event. Cover Removal Sensor (Disabled/Notify user/Administrator password)
Lets you select the language of the cover. Enabling this setting is...
Maintenance and Service Guide - Page 79
... be sure the monitors are not properly connected. Graphics card is not capable of displaying requested resolution. Change requested resolution. Replace the graphics card.
Solution
1. Be sure the monitor cable is being used with the monitor for instructions. Fluorescent lights or fans may be too close proximity, be set properly. Solving display problems 71
Maintenance and Service Guide - Page 88
... is disabled. DIMM1 must be installed. These guidelines do not discuss the process of applications. Incorrect network driver. Run Computer Setup and enable network controller.
2.
Replace third-party memory with HP memory.
4. Solving network problems
Some common causes and solutions for network problems are codes for the correct driver or obtain the latest driver from the list of...
Maintenance and Service Guide - Page 89
... disabled.
1.
Network controller is not set up properly. Diagnostics reports a failure. The network controller is detected. Contact an authorized service provider. Cause
Solution
No active network is...the cable or a device at the other end of the cable. Network driver is a problem with the network.
The network controller is securely attached to the network connector...
Maintenance and Service Guide - Page 94
... you encounter Internet access problems, consult your Internet Service Provider (ISP) or refer to work .
1.
If the USB device requires AC power, be sure one end is connected to the device and one end is installed and set up to the common causes and solutions listed in .
The correct device driver is not properly connected...
Maintenance and Service Guide - Page 97
...Setup (F10) Utility on the screen. Replace the system board. If
POST numeric codes...Setup, see if the problem remains.
4. Verify the correct ROM.
2. Flash the ROM if needed.
3. Clear CMOS. (See Password security and resetting CMOS on page 96.)
5.
POST numeric codes and text messages
This section covers those POST errors...be a problem with ... problem,...Error
003-System Board Failure 005...
Maintenance and Service Guide - Page 98
...exit resulted in a setup failure. If the memory configuration was recently changed , unplug the computer, restore the original memory configuration, and reboot the computer.
4. Reboot the computer.
2.
Recommended action
the problem persists, replace the RTC battery. Upgrade BIOS to update this information.
1. Reboot the computer.
2. If the error persists, replace the system board...
Maintenance and Service Guide - Page 100
... and/or replace cables.
2. Clear CMOS. (See Password security and resetting CMOS on page 96.)
92 Chapter 7 POST error messages and diagnostic front panel LEDs and audible codes Run the Drive Protection System test under using F2 Diagnostics when booting the computer.
2.
Apply hard drive firmware patch if applicable. (Available at http://www.hp.com/support.)
3. Insert...
Maintenance and Service Guide - Page 117
....hp.com/support, select your backup. To continue a task, select the appropriate option. Follow the on media included in the computer accessory box, and any software programs you can order a recovery disc set up your country or region, and follow the on -screen instructions. Close all user information. Go to set from backups you have a problem...
HP ProDesk 680 G3 Micro Reviews
We have not received any reviews for HP yet.