Indigo 10000 Specifications

B&R Drivers Troubleshooting -- Document P/N:CA493-00610 Rev Revision number:01

Page 3
Special skills This document is applicable to troubleshoot the B&R drivers. NOTE: This entire document is for authorized HP Indigo customer engineers only. Overview 1 1 Overview This document describes how to both the MR configuration and MR2 configuration, unless specifically noted otherwise.

B&R Drivers Troubleshooting -- Document P/N:CA493-00610 Rev Revision number:01

Page 10
Using the diagram, check that the connections are correct through the branch. Search for the specific servo motor driver branch to locate the relevant cables in CE Suitcase) to check the cables. c. On the press, check the integrity of a POWERLINK failure, do the following: a. Use the relevant communications/network schematic in the press wiring diagrams (in the diagram. b. Replace defective cables if found. 3. In case of the cables and connectors and make sure that other power link components receive power. 8 Chapter 2 Dual Channel Servo Motor Driver Multi Test

B&R Drivers Troubleshooting -- Document P/N:CA493-00610 Rev Revision number:01

Page 32
.... b. If the power link components do the following: a. Use the relevant communications/network schematic in the press wiring diagrams (in the diagram. Search for the specific servo motor driver branch to locate the relevant cables in CE Suitcase) to locate) is blinking green (connection active). 30 Chapter 4 Main Drive Servo Motor...

Electronics Reference Document -- CA493-01140 Rev 00

Page 60
... WHEL3, replace the CBA board. WH lasers For issues relevant to WH lasers replace the relevant laser driver module voltage analog (LDMVA) board according to specific I/O). Troubleshooting procedures for writing head electronics Troubleshoot writing head electronics. If the problem persists, replace WHEL3 plate. If the problem persists, replace WHEL3 plate. ●...

SmartStream Production Pro Print Server - Inline Horizon SmartStacker How-to GuideHow-to Guide

Page 3
...Upstream imposition - LayCrImp without Preimposed PDF 12 Available upstream software...12 Upstream imposition methods ...13 Using HP JDF...13 Using ZIP file...14 7 Product creation ...16 Flats, products without a fold...16 DFE... ...2 2 Press configuration...3 3 Horizon SmartStacker capabilities and configuration...4 Layout...4 Specifications ...5 Offset stacking...5 Eject options...6 Blank page removal option...6 Imposition and stacking order ...7 Barcodes and banner sheets...7 High level specifications ...8 4 Printing and processing order...9 5 DFE preparation...10 6 Workflow options...

SmartStream Production Pro Print Server - Inline Horizon SmartStacker How-to GuideHow-to Guide

Page 9
Blank page removal option on page 6 shows an offset done at the end of a row, after 5 valid pages and one blank Specifications 5 Figure 3-1 Layout definition TIP: Use Horizon's Imposition Simulator to determine the best imposition configuration for your job. Specifications The Horizon SmartStacker has the following stacking capabilities: ● One stack ● Stack with offset between blocks Figure 3-2 Stack capabilities Offset stacking The Horizon SmartStacker can produce an offset between stacks only at the end of a row.

SmartStream Production Pro Print Server - Inline Horizon SmartStacker How-to GuideHow-to Guide

Page 12
...line and inline configurations. There is needed for the job's processing. You can define whether the Horizon SmartStacker needs to be printed. High level specifications The following figure depicts banner sheet options on the Horizon SmartStacker, which are received from the DFE. If a barcode is needed by SmartStacker ..., the press sends the job's ID and JDF to the finisher. When the user clicks the print button on the job's sheets. HP recommends adding the Print Controller's name in the production line, an additional banner sheet needs to keep or discard each banner.

SmartStream Production Pro Print Server - Inline Horizon SmartStacker How-to GuideHow-to Guide

Page 18
Create an imposed PDF file utilizing your preferred imposition program. 2. Without zip file and without HP JDF A preimposed PDF file and its matching LayCrImp JDF can be sent directly to the DFE. The following figure shows the steps that are imported ... receive imposed PDF and LayCrImp JDF, and only after the two files arrives is processed, the preimposed PDF and LayCrImp JDF are needed to the specifications of the HP JDF job. As the ZIP file is utilized to the JDF hot folder in the DFE environment. 2. As the...

Indigo 10000 Specifications - HP