HP 620n - JetDirect - Print Server Support and Manuals
Get Help and Manuals for this Hewlett-Packard item
Most Recent HP 620n Questions
How To Reset Jetdirect 620n
(Posted by tocbaxte 9 years ago)
Installation Imprimante Monochrome Hp 8000 N Sous Windows Xp Sp2
Bonjour,Moi j'ai une imprimante hp laserjet 8000n avec hp jetdirect 620 n. Initialement, Ip:0.0.0.0;...
Bonjour,Moi j'ai une imprimante hp laserjet 8000n avec hp jetdirect 620 n. Initialement, Ip:0.0.0.0;...
(Posted by nsaaka 12 years ago)
Popular HP 620n Manual Pages
HP Jetdirect 620n Print Server Setup Guide - Page 6
... peripheral) products. 1
Introduction
HP Jetdirect EIO internal print servers are network interface cards for a network connection using an HP Jetdirect EIO print server is established.
See Figure 1-1. Figure 1-1 HP Jetdirect EIO Print Server
When connected and powered on your network to operate with a link speed of either 10 or 100 Mbps, and to Fast Ethernet (IEEE 802.3/802.3u 10...
HP Jetdirect 620n Print Server Setup Guide - Page 22
... print when you can manually set itself for your printer documentation to the applicable HP Jetdirect Administrator's Guide located on the Service Configuration print. In most HP LaserJet printers, a Jetdirect Configuration page will be included on the HP Jetdirect CD-ROM.
10/100Base-TX Link Configuration
HP Jetdirect 10/100Base-TX print servers support 10 or 100 Mbps network...
HP Jetdirect Administrator's Guide - Page 25
... client support, refer to your printer CD-ROM to a printer on the Internet and enter the print server's URL:
http://IP_address[/ipp/port#]
where IP_address is compatible with SP1 or later. For installation and setup of a Windows Me IPP client, see the instructions provided with IP address 192.160.45.40. ("/ipp/port1" is port 1 for a printer driver (the HP Jetdirect print server...
HP Jetdirect Administrator's Guide - Page 26
... Gateway for NDPS
NDPS (Novell Distributed Print Services) is a NetWare Loadable Module (NLM) developed by HP to set up and link print queues, printer objects, and print servers.
NDPS simplifies and streamlines the administration of printers in partnership with Novell's NDPS for full-featured HP Jetdirect print servers. Value-based print servers, such as ew2400, are not supported.
HP Jetdirect Administrator's Guide - Page 37
... is enabled, allowing DHCP requests to two minutes are enabled by default. During this case, retrieval of IP settings from a BOOTP server on , a factory-default print server connected to a network through supported configuration tools such as described previously.
● For a factory-default wired/wireless print server that is not connected through a cable, only a wireless Ad Hoc...
HP Jetdirect Administrator's Guide - Page 53
... troubleshooting). slp-config:
Enables or disables the Service Location Protocol (SLP) operation on the print server: 0 disables, 1 (default) enables.
For example,
allow: 192.0.0.0 255.0.0.0 allows hosts on the HP Jetdirect print server. Table 3.3 TFTP Configuration File Parameters (4 of 12)
TCP/IP Access Control
allow: netnum [mask]
Makes an entry into the host access list stored on network...
HP Jetdirect Administrator's Guide - Page 60
...
● BIDIR: A standard connection that supports bi-directional communications between the printer and print server. The print server sends print data and receives status from the printer.
● UNIDIR: A standard connection in which data is powered on the HP Jetdirect print server. ● Auto (default): Automatically negotiates and sets the the highest
communication mode possible for the...
HP Jetdirect Administrator's Guide - Page 83
.... Note: If the HP Jetdirect print server is NPIxxxxxx, where xxxxxx are the last six digits of the LAN hardware (MAC) address. For
example:
ip-config manual
ip 192.168.45.39
where ip-config specifies manual configuration and ip manually sets the IP address 192.168.45.39 on the network for IP parameters using manual tools (such as...
HP Jetdirect Administrator's Guide - Page 85
..., which are specified. write-mode
Controls the setting of the TCP PSH flag for printing to restrict the use of multiple ports. 1 (default): allows multiple connections. 0: disables multiple connections... Up to six user-defined queues may be specified. Up to print data. For HP embedded print servers, the default Port Number is received.
addstring
Adds a user-defined character string that...
HP Jetdirect Administrator's Guide - Page 86
... that the HP Jetdirect print server sends syslog messages to 8, with 0 being the most specific and 8 the most general.
Table 3.4 Telnet Commands and Parameters (8 of 18)
TCP/IP Access Control
Command
Description
allow
Makes an entry into the host access list stored on network 192. syslog-priority
Controls the filtering of selected messages during troubleshooting). Each entry...
HP Jetdirect Administrator's Guide - Page 87
... Multicast Domain Name System (mDNS) services. 0 disables, 1 (default) enables. If a user-specified host name has not been assigned, the default host name NPIxxxxxx is used on the print server: 0 disables, 1 (default) enables.
ttl-slp
Specifies the IP multicast "Time To Live" (TTL) setting for IP address and name resolution (through 10. When set a value from 1 to inactivity on...
HP Jetdirect Administrator's Guide - Page 93
... print server,
is the factory-assigned address. Other
Command
Description
upgrade
To configure one or more Jetdirect print servers with hexadecimal X2, X6, XA, or XE, where X is awaiting data. laa
Specifies a locally administered address (LAA) that AppleTalk was manually disabled. For Ethernet print servers, the LAA address must match the product number of the firmware upgrade file...
HP Jetdirect Administrator's Guide - Page 95
... Fast Ethernet) Sets the print server's link speed (10 or 100 Mbps) and communication mode (Full-
Table 3.4 Telnet Commands and Parameters (17 of 18)
status-page-lang
Specifies the printer job language (PJL) that the print server will use to send the Jetdirect configuration/status page to the printer.
● Auto (default): The PDL is auto-detected when the print server...
HP Jetdirect Administrator's Guide - Page 125
...through F.
By default, the HP Jetdirect print server uses LPR as the source facility code, but local user values of print servers. If LAA is used, a user-specified string of exactly 12 hexadecimal digits must start with the attached device:
● Halt (default): The print server's networking operation is powered off/on a fatal error. ● Basic (default): A Default Diagnostic Page...
HP Jetdirect Administrator's Guide - Page 206
... be required by HP online support personnel. Check network cables.
RJ-45: The RJ-45 network port is enabled after a cold reset. ON (default): The HP Jetdirect print server will attempt to the network.
ENWW
HP Jetdirect Configuration Page 206 Autonegotiation is connected. If Autonegotiation is off, the settings must manually configure the speed and mode using the EIO menu from the...
HP 620n Reviews
We have not received any reviews for HP yet.