HP Jetdirect 690n - IPv6/IPSec 802.11g Wireless Print Server Support and Manuals
Get Help and Manuals for this Hewlett-Packard item
This item is in your list!
View All Support Options Below
Free HP Jetdirect 690n manuals!
Problems with HP Jetdirect 690n?
Ask a Question
Free HP Jetdirect 690n manuals!
Problems with HP Jetdirect 690n?
Ask a Question
Popular HP Jetdirect 690n Manual Pages
HP Jetdirect Print Servers - Administrator's Guide - Page 11
...can install it with a supported printer or multifunction peripheral (MFP).
Table 1-1 Supported HP Jetdirect print server features and capabilities
Model
Product Number Printer Connect
Network Connect1
Network Protocols and Features2
Firmware Version3
690n
J8007G
635n
J7961G
630n Not Applicable
J7997G J8010E
Not Applicable
J8011E
Not Applicable
J8013E
EIO EIO EIO Embedded...
HP Jetdirect Print Servers - Administrator's Guide - Page 12
... HP Jetdirect print server features and capabilities (continued)
Model
Product Number Printer Connect
Network Connect1
Network Protocols and Features2
Firmware Version3
Not Applicable
J8017E
Embedded
10/100-TX or
Full
10/100/1000T
V38.xx.nn
1 Embedded HP Jetdirect print server support for 100T (Gigabit) depends on both the print server and printer/MFP in which it is installed...
HP Jetdirect Print Servers - Administrator's Guide - Page 15
.../support/net_printing
Firmware upgrades
Full-featured HP Jetdirect print servers support firmware upgrades of the following installation tools: ● HP Jetdirect download manager (Windows) Download from HP online support at :
http://www.hp.com/go /webjetadmin_firmware
Firmware installation tools
Install firmware upgrades for the applicable HP Jetdirect
product models. The following manuals...
HP Jetdirect Print Servers - Administrator's Guide - Page 27
... The print server does not support dynamic updates to be provided by a server, such as a domain name or DNS server addresses.
These messages contain one of IPv6 DNS servers for networks that other configuration be routed but with a 64-bit host address derived from the print server's MAC address to form the IPv6 stateless addresses configured on HP Jetdirect print servers.
IPv6...
HP Jetdirect Print Servers - Administrator's Guide - Page 31
... Use installation, setup, and management software running on a BOOTP server that you can configure an HP Jetdirect print server with Legacy default IP address 192.0.0.192) Use the arp and ping commands from a network-based server by the printer.
● DHCP/TFTP Use DHCP and TFTP each time the printer is recommended only during troubleshooting or for simple installations. Because HP-UX...
HP Jetdirect Print Servers - Administrator's Guide - Page 34
..., that set this to ether (for a specific peripheral.
Specify the domain name for the HP Jetdirect print server (for example "pathname". lease-time
51
DHCP IP address lease duration time. T145
-- T146
-- HP proprietary.
IP address tag (required) of the TFTP configuration file.
Specify the path name
using double quotes, for example,
support.hp.com).
Specify...
HP Jetdirect Print Servers - Administrator's Guide - Page 44
...
ENWW If you set all print server lease durations to install or enable DHCP services. On HP-UX systems, a sample DHCP configuration file (dhcptab) might be available on page 22. This ensures that the HP Jetdirect print server uses. Windows systems
HP Jetdirect print servers support IP configuration from changing IP addresses, HP recommends assigning printers IP addresses with your system...
HP Jetdirect Print Servers - Administrator's Guide - Page 54
...) The media access control (MAC) address of the access point used for communicating on the network for Infrastructure mode communications, as Telnet, the embedded Web server, the control panel, or installation/management software. Poor/Marginal/Good/Excellent: Detected signal strength level. Reset security settings on fullfeatured print servers that do not support IPsec, but allow Firewall...
HP Jetdirect Print Servers - Administrator's Guide - Page 68
... following (see your printer documentation.
NOTE: This procedure resets all parameters to factory default values, see Troubleshoot the HP Jetdirect print server on page 61. Move to a new network, make sure that network. Parameters for instructions to reset the print server to factory default settings. If the current BOOTP server is installed.
If the IP address was configured using...
HP Jetdirect Print Servers - Administrator's Guide - Page 74
... or click Cancel to erase your system to wireless network connection parameters on HP Jetdirect wireless print servers. If the print server loses its network connection, you might resolve an IP address for example, printer1.support.hp.com), enter the host name (in brackets ([ ]).
By factory default, HP Jetdirect print servers and printers/MFPs with security alerts, click Yes to a factory...
HP Jetdirect Print Servers - Administrator's Guide - Page 91
... than the print server's installed version.
You can set up to locate it is disabled, go /webjetadmin_firmware
From the HP online firmware upgrade page, use this tab to the Misc.
To identify and retrieve the appropriate upgrade file, click HP Jetdirect Firmware Updates (Internet access required), or visit HP online support at:
http://www.hp.com/go to upgrade the print server with...
HP Jetdirect Print Servers - Administrator's Guide - Page 100
... your organization is located. ● State/Province (Required for all print servers or devices support ACL, and support is probably invalid for the file. Then enter the password that are overwritten. Access Control
Use this default address to display the access control list (ACL) on the HP Jetdirect print server.
Do not use this tab to identify your device.
●...
HP Jetdirect Print Servers - Administrator's Guide - Page 139
... by the print server are important tools for managing or troubleshooting HP Jetdirect print servers. For instructions, see your printer manuals. For printers with general security settings. If supported by accessing the embedded Web server on the attached printer. The Security configuration page is printed. The format of supported network protocols. 8 HP Jetdirect configuration pages...
HP Jetdirect Print Servers - Administrator's Guide - Page 145
... wireless print server is in ad hoc mode. WEP: Each device on any channel)
: No radio signal detected while the print server is scanning. Authentication failures for network access unless the network requires EAP authentication. IPsec or Firewall
If the print server and printer/MFP device supports IPsec, then IPsec appears. ENWW
HP Jetdirect configuration page 135 Security Settings...
HP Jetdirect Print Servers - Administrator's Guide - Page 154
... LAN ERROR - If the error persists, replace the print server.
0C LAN ERROR - UNDERFLOW
(Ethernet) Check the cabling and connectors on again. Use the installation software, embedded Web server, or other tools to service queries for the NetWare functions is running and that the name configured on the HP Jetdirect print server matches the actual name used by turning the printer off and...
HP Jetdirect 690n Reviews
Do you have an experience with the HP Jetdirect 690n that you would like to share?
Earn 750 points for your review!
We have not received any reviews for HP yet.
Earn 750 points for your review!