Harbor Freight Tools 98199 - 10 in. Sliding Compound Miter Saw Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
This item is in your list!
View All Support Options Below
Free Harbor Freight Tools 98199 manuals!
Problems with Harbor Freight Tools 98199?
Ask a Question
Free Harbor Freight Tools 98199 manuals!
Problems with Harbor Freight Tools 98199?
Ask a Question
Most Recent Harbor Freight Tools 98199 Questions
Looking For Kerf For Chicago Electric 98199 Miter Saw Part 21
(Posted by deknapp 11 months ago)
Popular Harbor Freight Tools 98199 Manual Pages
User Manual - Page 3
... replaced.
20. Keep tools sharp and clean for future reference.
1. Follow instructions for recommended accessories. USE PROPER EXTENSION CORD. An undersized cord will operate properly and perform its operation. The smaller the gauge number, the heavier the cord.
15. DISCONNECT TOOLS before servicing; REDUCE THE RISK OF UNINTENTIONAL STARTING. Consult the owner's manual for...
User Manual - Page 5
...specific hazards in the work before changing blade or servicing....settings.
7. Do not use to protect against the failure of inattention while operating power tools may result in place.
4. Return all guards for your Own Safety Read Instruction Manual Before Operating Miter Saw
1. Never reach around saw are doing and use only identical replacement parts... . SAFETy
SETUP
Miter Saw ...
User Manual - Page 6
...work in this product, but must be built into this instruction manual cannot cover all possible conditions and situations that may cause... Safety Code § 25249.5, et seq.)
26.
Pregnant women or people who have regular medical check-ups to ensure medical problems are...tool vibrates during use . SAFETy
SETUP
Miter Saw Safety Warnings (cont.)
25. Anyone using vibrating tools...
User Manual - Page 8
SAFETy
SETUP
Trigger Blade Guard
Handles
Blade Lock
Dust Collection Bag
Blade
Hold Down Clamp
Miter Handle
Kerf Board
Table
Miter Lock Handle
Miter Angle Indicator
Figure A: Components
Bevel Angle Indicator
Fence
Work piece Extension Support
OPERATION
MAINTENANCE
Page 8
For technical questions, please call 1-888-866-5797. ITEM 98199
User Manual - Page 9
...set up or use of the Extension Supports into the Plate until securely in place. Insert the ends of this product. There are bolt holes provided in the bag. Sawdust created by cutting is captured in each of the four legs of this manual...the Blade Housing Assembly.
SAFETy
SETUP
Setup -
This may be firmly mounted using... information regarding the parts listed in the following...
User Manual - Page 10
...before set up...Set Up
1. devices (not included). The Miter Saw must be secured to possible damage. SETUP
OPERATION
MAINTENANCE
Page 10
For technical questions, please call 1-888-866-5797. SAFETy
Operating Instructions
Read the ENTIRE IMPORTANT SAFETy INFORMATION section at the beginning of this manual including all text under subheadings therein before making any
work materials supports...
User Manual - Page 11
... to unlock the Table. Bevel cuts can read the angle on both left to support the work piece.
3. SAFETy
SETUP
TOOL SET UP
Using the Work Piece Extension Supports
1. When properly installed, the upper face of the saw horses or other supports (not included) to the desired angle. Using the Depth Stop
1. REV 10f
Page 11...
User Manual - Page 12
... of the Guide Fence, miter...supported before making a cut .
If the material binds the blade, release the trigger. Keep your measured mark, keeping the kerf on each of the blade. SAFETy
SETUP
General Operating Instructions...assembly to
set the miter...manual. Observe all safety and planning items
6. Unlock the Slide using the Hold Down Vise.
Using the Work Piece Extension Supports...
User Manual - Page 13
... of the tool to clean it must be replaced
only by a qualified technician.
accidents, turn off as other condition that accumulates on the cuts.
9. WARNING! SETUP
OPERATION
MAINTENANCE
ITEM 98199
For technical questions, please call 1-888-866-5797. SAFETy
Maintenance and Servicing
Procedures not specifically explained in this manual must be performed only by a qualified...
User Manual - Page 14
... it counterclockwise. (See Figure B.)
SETUP
OPERATION
Figure B: Removing Bolt 4. Replace the Outer Flange and Arbor Bolt.
Lock the blade assembly in place after replacing blade.
1. Reinstall a new Blade...Center Cover Fixing Bolt using the Wrench by turning it counterclockwise.
10.
SAFETy
Replacing the Blade
WARNING
TO REDUCE RISK OF SERIOUS INJURy: Return guard to match the...
User Manual - Page 15
... is at 90º.
2. Replace the four screws and tighten them slightly. Loosen the Bevel Lock and set at 90º to read ... holding the Kerf Board in place using a soft mallet. Install a new Kerf Board. Rotate it must be corrected by ...the Table set the Bevel Angle at exactly 90º. Tighten the four screws holding the Angle Indicator in place. SAFETy
SETUP
Adjusting the...
User Manual - Page 16
.... Disconnect power supply before service. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. SAFETy
SETUP
Troubleshooting
Problem
Tool will not start
Tool...
User Manual - Page 17
Parts List and Diagram
Parts List
SAFETy
SETUP
OPERATION
Part Description
1 Bolt M6X25 2 Base 3 Extension Arm 4 Screw 5 Feet 6...42 Washer
ITEM 98199
Qty
2 1 2 2 4 1 4 8 4 1 1 1 1 1 1 1 1 1 2 9 1 1 1 1 1 1 1 1 8 8 4 1 1 1 1 1 1 2 1 1 2 1 2
Part Description Qty
43 Bolt
1
44 Lock Handle
1
45 Lock Pin Spring
1
46 Bolt
1
47 Bolt M5X14
2
49 Oil Cover
2
50 Bearing
2
51 Rod
2
52 Mount...
User Manual - Page 18
Assembly Diagram
SAFETy
SETUP
OPERATION
MAINTENANCE
Page 18
For technical questions, please call 1-888-866-5797. ITEM 98199
User Manual - Page 19
Page 19 Assembly Diagram (cont.)
SAFETy
SETUP
OPERATION
MAINTENANCE
Record Product's Serial Number Here: Note: If product has no serial number, record month and year of purchase instead.
ITEM 98199
For technical questions, please call 1-888-866-5797.
Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.
Harbor Freight Tools 98199 Reviews
Do you have an experience with the Harbor Freight Tools 98199 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Harbor Freight Tools yet.
Earn 750 points for your review!