Harbor Freight Tools 98199 Support Question
Harbor Freight Tools 98199 Support Question
Find answers below for this question about Harbor Freight Tools 98199 - 10 in. Sliding Compound Miter Saw.Need a Harbor Freight Tools 98199 manual? We have 1 online manual for this item!
Question posted by deknapp on May 1st, 2023
Looking For Kerf For Chicago Electric 98199 Miter Saw Part 21
The person who posted this question about this Harbor Freight Tools product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by SonuKumar on May 1st, 2023 10:12 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,617,810
Member since:
May 9th, 2021 Points: 16,617,810
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Harbor Freight Tools 98199 Manual Pages
User Manual - Page 2
... death or serious injury. Addresses practices not related to avoid possible injury or death.
It is the safety alert symbol. ITEM 98199
SAFETy
Table of Contents
Safety 3 Setup 7 Specifications 7 Operation 10
Maintenance 13 Parts List and Diagram 17 Warranty 20
WARNING SyMBOLS AND DEFINITIONS This is used to alert you to potential...
User Manual - Page 3
... and safest performance. USE RIGHT TOOL. Don't force tool or attachment to use of the blade or cutter only.
21. USE RECOMMENDED ACCESSORIES. DIRECTION OF...use one heavy enough to see that it was designed.
10. A guard or other jewelry which it will draw....tool is tipped or if the cutting tool is in damp or wet locations, or expose them to operate tool.
13. ITEM 98199...
User Manual - Page 4
... not fit fully in any way.
2. ITEM 98199 If it still does not fit, contact a qualified electrician to install the proper outlet. Double insulated tools may be used in a polarized outlet only one blade is wider than the other). SAFETy
Grounding Instructions
TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION...
User Manual - Page 5
... hands out of path of saw blade.
6. Turn off tool and wait for saw blade to begin work area.
20. Check all have appropriate ventilation whenever cutting pressure treated lumber.
13. The blade washers and bolt were specially designed for your Own Safety Read Instruction Manual Before Operating Miter Saw
1. Do not depress the spindle...
User Manual - Page 6
...bricks and cement or other reproductive harm.
Anyone using vibrating tools regularly or for an extended period should not use this manual. ITEM 98199 Include vibration-free periods each day of California to filter ...term exposure to the hands, arms and shoulders. SAFETy
SETUP
Miter Saw Safety Warnings (cont.)
25. To reduce your exposure to these chemicals are factors which cannot ...
User Manual - Page 7
... 0° - 45° left
1° per scale mark
250100
List of Contents
Description
Qty
Compound Sliding Miter Saw
1
Carbide Tipped Blade
1
Table Extensions
2
Dust Collection Bag
1
Wrench
1
SETUP
OPERATION
MAINTENANCE
ITEM 98199
For technical questions, please call 1-888-866-5797. SAFETy
Specifications
Motor Arbor Diameter Blade Type Blade Diameter Cutting Capacity
Positive...
User Manual - Page 8
ITEM 98199 SAFETy
SETUP
Trigger Blade Guard
Handles
Blade Lock
Dust Collection Bag
Blade
Hold Down Clamp
Miter Handle
Kerf Board
Table
Miter Lock Handle
Miter Angle Indicator
Figure A: Components
Bevel Angle Indicator
Fence
Work piece Extension Support
OPERATION
MAINTENANCE
Page 8
For technical questions, please call 1-888-866-5797.
User Manual - Page 9
... Handle
1.
There are bolt holes provided in the bag. OPERATION
MAINTENANCE
ITEM 98199
For technical questions, please call 1-888-866-5797. The upper edge of this product. These should be mounted on .
2. Mounting the Saw
The Miter Saw must be firmly mounted using bolts (not included) to the Assembly Diagram near the end of...
User Manual - Page 10
...saw , work area must provide a surface on both left and right of this tool. is clean and well-lit.
4. ITEM 98199 Route the power cord along a safe route to prevent injury and distraction. The Miter Saw... tripping hazard or exposing the power cord to this product.
SETUP
OPERATION
MAINTENANCE
Page 10
For technical questions, please call 1-888-866-5797. Clamping the work piece will ...
User Manual - Page 11
...to the desired angle. Bevel cuts can use saw .
To make a kerfing or rabbet cut which does not cut , loosen the Miter Lock Knob by pressing in the Lock Button and...98199
For technical questions, please call 1-888-866-5797. The table will be used in the material. Move the blade assembly left and right sides.
3. You can be .
3.
Compound angle cuts are level with a miter...
User Manual - Page 12
... the Slide, loosen
the Slide Lock Wing Screw at the desired miter angle.
Check to be sure the slide lock is
raised the Blade Guard returns to prevent tear-out are discussed later in place using the Bevel Lock Lever. This is provided with
the proper movement of the saw blade. Adjustment of the Kerf Board...
User Manual - Page 13
...qualified service technician. Cleaning, Maintenance, and Lubrication
1. other moving parts. Keep the Slides free of children's reach.
7. SETUP
OPERATION
MAINTENANCE
ITEM 98199
For technical questions, please call 1-888-866-5797. accidents, turn off the tool and disconnect its electrical outlet before further use. WARNING! Page 13 Observe the Dust Bag while using the...
User Manual - Page 14
...in place by turning it counterclockwise.
10. While holding the Center Cover in.... Reinstall a new Blade on the saw Blade Housing. Rotate the Center Cover ... blade.
1. Release the Locking Pin. Unplug the tool from its power source.
2. Raise the Blade Guard...Removing Blade
9.
Remove the Arbor Bolt, Outer Flange and Saw Blade by turning clockwise.
7. Lock the blade assembly in ...
User Manual - Page 15
...Kerf Board
If the Kerf Board becomes damaged it is at exactly 90º. Install a new Kerf Board. Tighten the four screws holding the Angle Indicator in place.
3. OPERATION
MAINTENANCE
ITEM 98199...Saw Blade and lock it until the Fence is accurately adjusted, tighten the bolts firmly in the vertical position. First unplug the tool...screw holding the Kerf Board in a miter or bevel angle....
User Manual - Page 16
...the saw . Bottom and back side are not supported.
2. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect.... 1. Likely Solutions
1. Check for precision cuts use a thin kerf blade with 60 or more teeth. 4. Use a thin piece ... flush against the fence and supported on ends. 1. ITEM 98199 Clean Blade using blade cleaner or mineral spirits. 2.
Material is...
User Manual - Page 17
... M5X10 8 Spring Washer 9 Flat Washer 10 Plate 11 Rub Slice 12 Pin 13... Bolt M4X8 21 Kerf 22 Plate 23... 33 Screw 34 Bolt 35 Flat Washer 36 Pointer 37 Nut 38 Spring 39 Bend Arm 40 Flat Washer 41 Lock Nut 42 Washer
ITEM 98199
Qty
2 1 2 2 4 1 4 8 4 1 1 1 1 1 1 1 1 1 2 9 1 1 1 1 1 1 1 1 8...
54 Washer
2
55 Bolt M6X10
4
56 Limit Plate
1
57 Slide Lock Wing Screw 1
58 Handle Ball
1
59 Lock Spring
1
...
User Manual - Page 18
ITEM 98199 Assembly Diagram
SAFETy
SETUP
OPERATION
MAINTENANCE
Page 18
For technical questions, please call 1-888-866-5797.
User Manual - Page 19
Page 19
Assembly Diagram (cont.)
SAFETy
SETUP
OPERATION
MAINTENANCE
Record Product's Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.
ITEM 98199
For technical questions, please call 1-888-866-5797.
User Manual - Page 20
... Box 6009 • Camarillo, CA 93011 • 1-888-866-5797 This warranty gives you specific legal rights and you . Limited 90 Day Warranty
Harbor Freight Tools Co. To take advantage of this product is no event be returned to lack of our warranty, then you with transportation charges prepaid.
Similar Questions
Charger For Item 62421 (chicago Electric 18v Cordless Impact Driver)
I lost the charger for this item. Do you have one available for purchase
I lost the charger for this item. Do you have one available for purchase
(Posted by dys2 1 year ago)
Harbor Freight 10” Sliding Compound Saw Handle Replacement
I purchased a Harbor Freight 10" sliding compound saw at a store sidewalk sale a number of years ago...
I purchased a Harbor Freight 10" sliding compound saw at a store sidewalk sale a number of years ago...
(Posted by Br1nkl3yrose 2 years ago)
Measurements For Connecting Bar For 61969 - 12 In. Miter Saw
61969 - Chicago Electric 12 in. Double-Bevel Sliding Compound Miter Saw.I bought this miter saw but ...
61969 - Chicago Electric 12 in. Double-Bevel Sliding Compound Miter Saw.I bought this miter saw but ...
(Posted by mathewpatterson 2 years ago)
Need 102 Outer Fllange For Chicago Electric 10” Sliding Compound Miter Saw Ite
looking for outer flange for Chicago electric 19" sliding compound miter saw item 61972
looking for outer flange for Chicago electric 19" sliding compound miter saw item 61972
(Posted by nelliethedog1 2 years ago)
Chicago Electric Half Inch Impact Wrench
Hello, I have a Chicago half inch impact gun model number 45252 and I need brushes for this item, co...
Hello, I have a Chicago half inch impact gun model number 45252 and I need brushes for this item, co...
(Posted by wrski 6 years ago)